#define CONFIG_MISC_INIT_R
-#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
-#define BOOTFLAG_WARM 0x02 /* Software reboot */
+#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
+#define BOOTFLAG_WARM 0x02 /* Software reboot */
-#define CFG_CACHELINE_SIZE 32 /* For MPC5xxx CPUs */
+#define CFG_CACHELINE_SIZE 32 /* For MPC5xxx CPUs */
#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
-# define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */
+# define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */
#endif
/*
*/
#if !defined(CONFIG_PRS200)
/* MCC200 configuration: */
-#undef CONFIG_PSC_CONSOLE
+#define CONFIG_SERIAL_MULTI 1
+#define CONFIG_PSC_CONSOLE 1 /* PSC1 may be COM */
+#define CONFIG_PSC_CONSOLE2 2 /* PSC2 is PSoC */
#else
/* PRS200 configuration: */
#define CONFIG_PSC_CONSOLE 1 /* console is on PSC1 */
#endif
-#if defined(CONFIG_QUART_CONSOLE) && defined(CONFIG_PSC_CONSOLE)
+#if defined(CONFIG_QUART_CONSOLE) && defined(CONFIG_PSC_CONSOLE) && \
+ !defined(CONFIG_SERIAL_MULTI)
#error "Select only one console device!"
#endif
#define CONFIG_BAUDRATE 115200
/* USB */
#define CONFIG_USB_OHCI
-#define ADD_USB_CMD CFG_CMD_USB | CFG_CMD_FAT
+#define ADD_USB_CMD CFG_CMD_USB | CFG_CMD_FAT
#define CONFIG_USB_STORAGE
+/* automatic software updates (see board/mcc200/auto_update.c) */
+#define CONFIG_AUTO_UPDATE 1
/*
* Supported commands
#undef CONFIG_BOOTARGS
-#define XMK_STR(x) #x
-#define MK_STR(x) XMK_STR(x)
+#define XMK_STR(x) #x
+#define MK_STR(x) XMK_STR(x)
#ifdef CONFIG_PRS200
-# define CFG__BOARDNAME "prs200"
+# define CFG__BOARDNAME "prs200"
+# define CFG__LINUX_CONSOLE "ttyS0"
#else
-# define CFG__BOARDNAME "mcc200"
+# define CFG__BOARDNAME "mcc200"
+# define CFG__LINUX_CONSOLE "ttyEU7"
#endif
#define CONFIG_EXTRA_ENV_SETTINGS \
"addip=setenv bootargs ${bootargs} " \
"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
":${hostname}:${netdev}:off panic=1\0" \
- "addcons=etenv bootargs ${bootargs} " \
+ "addcons=setenv bootargs ${bootargs} " \
"console=${console},${baudrate}\0" \
"flash_nfs=run nfsargs addip addcons;" \
"bootm ${kernel_addr}\0" \
"bootm ${kernel_addr} ${ramdisk_addr}\0" \
"net_nfs=tftp 200000 ${bootfile};" \
"run nfsargs addip addcons;bootm\0" \
- "console=ttyS0\0" \
+ "console=" CFG__LINUX_CONSOLE "\0" \
"rootpath=/opt/eldk/ppc_6xx\0" \
"bootfile=/tftpboot/" CFG__BOARDNAME "/uImage\0" \
"load=tftp 200000 /tftpboot/" CFG__BOARDNAME "/u-boot.bin\0" \
/*
* IPB Bus clocking configuration.
*/
-#define CFG_IPBSPEED_133 /* define for 133MHz speed */
+#define CFG_IPBCLK_EQUALS_XLBCLK /* define for 133MHz speed */
/*
* I2C configuration
*/
#define CONFIG_HARD_I2C 1 /* I2C with hardware support */
-#define CFG_I2C_MODULE 1 /* Select I2C module #1 or #2 */
+#define CFG_I2C_MODULE 2 /* Select I2C module #1 or #2 */
#define CFG_I2C_SPEED 100000 /* 100 kHz */
#define CFG_I2C_SLAVE 0x7F
* TEXT base always at 0xFFF00000
* ENV_ADDR always at 0xFFF40000
* FLASH_BASE at 0xFC000000 for 64 MB (only 32MB are supported, not enough addr lines!!!)
- * 0xFE000000 for 32 MB
- * 0xFF000000 for 16 MB
- * 0xFF800000 for 8 MB
+ * 0xFE000000 for 32 MB
+ * 0xFF000000 for 16 MB
+ * 0xFF800000 for 8 MB
*/
#define CFG_FLASH_BASE 0xfc000000
#define CFG_FLASH_SIZE 0x04000000
#define CFG_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */
#define CFG_FLASH_QUIET_TEST 1 /* don't warn upon unknown flash */
-#define CFG_ENV_IS_IN_FLASH 1 /* use FLASH for environment vars */
+#define CFG_ENV_IS_IN_FLASH 1 /* use FLASH for environment vars */
-#define CFG_ENV_SECT_SIZE 0x40000 /* size of one complete sector */
+#define CFG_ENV_SECT_SIZE 0x40000 /* size of one complete sector */
#define CFG_ENV_ADDR (CFG_MONITOR_BASE + CFG_MONITOR_LEN)
#define CFG_ENV_SIZE 0x2000 /* Total Size of Environment Sector */
#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
-#define CFG_MONITOR_BASE TEXT_BASE
+#define CFG_MONITOR_BASE TEXT_BASE
#if (CFG_MONITOR_BASE < CFG_FLASH_BASE)
# define CFG_RAMBOOT 1
#endif
#define CONFIG_PHY_ADDR 1
/*
+ * LCD Splash Screen
+ */
+#if !defined(CONFIG_PRS200)
+#define CONFIG_LCD 1
+#define CONFIG_PROGRESSBAR 1
+#endif
+
+#if defined(CONFIG_LCD)
+#define CONFIG_SPLASH_SCREEN 1
+#define CFG_CONSOLE_IS_IN_ENV 1
+#define LCD_BPP LCD_MONOCHROME
+#endif
+
+/*
* GPIO configuration
*/
/* 0x10000004 = 32MB SDRAM */
/* 0x90000004 = 64MB SDRAM */
+#if defined(CONFIG_LCD)
+/* set PSC2 in UART mode */
+#define CFG_GPS_PORT_CONFIG 0x00000044
+#else
#define CFG_GPS_PORT_CONFIG 0x00000004
+#endif
/*
* Miscellaneous configurable options
*/
-#define CFG_LONGHELP /* undef to save memory */
-#define CFG_PROMPT "=> " /* Monitor Command Prompt */
+#define CFG_LONGHELP /* undef to save memory */
+#define CFG_PROMPT "=> " /* Monitor Command Prompt */
#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
-#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
+#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
#else
-#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
+#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
#endif
-#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
+#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
#define CFG_MAXARGS 16 /* max number of command args */
#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
-#define CFG_MEMTEST_START 0x00100000 /* memtest works on */
+#define CFG_MEMTEST_START 0x00100000 /* memtest works on */
#define CFG_MEMTEST_END 0x00f00000 /* 1 ... 15 MB in DRAM */
#define CFG_LOAD_ADDR 0x100000 /* default load address */
projects / platform / kernel / u-boot.git / blobdiff