* actual resources get mapped (not physical addresses)
*----------------------------------------------------------------------*/
#define CFG_SDRAM_BASE 0x00000000
-#define CFG_FLASH_BASE 0xFE000000
+#define CFG_FLASH_BASE 0xFC000000
#define CFG_FPGA_BASE 0xF0000000
#define CFG_PERIPHERAL_BASE 0xEF600000 /* internal peripherals*/
#define CFG_MONITOR_LEN (384 * 1024) /* Reserve 384 kB for Monitor */
-#define CFG_MALLOC_LEN (128 * 1024) /* Reserve 128 kB for malloc() */
+#define CFG_MALLOC_LEN (512 * 1024) /* Reserve 512 kB for malloc() */
#define CFG_MONITOR_BASE (TEXT_BASE)
/*-----------------------------------------------------------------------
/*-----------------------------------------------------------------------
* DDR SDRAM
*----------------------------------------------------------------------*/
-#define CFG_MBYTES_SDRAM 128
+#define CFG_MBYTES_SDRAM 256
/*-----------------------------------------------------------------------
* I2C
#define CONFIG_NET_MULTI 1
#define CONFIG_HAS_ETH1 1 /* add support for "eth1addr" */
-#define CONFIG_PHY1_ADDR 2
+#define CONFIG_PHY1_ADDR 0
#define CFG_RX_ETH_BUFFER 32 /* Number of ethernet rx buffers & descriptors */
#define CONFIG_PREBOOT "echo;" \
- "echo Type \"run flash_nfs\" to mount root filesystem over NFS;" \
+ "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \
"echo"
#undef CONFIG_BOOTARGS
"bootfile=makalu/uImage\0" \
"fdt_file=makalu/makalu.dtb\0" \
"fdt_addr=400000\0" \
- "kernel_addr=fe000000\0" \
- "ramdisk_addr=fe200000\0" \
+ "kernel_addr=fc000000\0" \
+ "ramdisk_addr=fc200000\0" \
"initrd_high=30000000\0" \
"load=tftp 200000 makalu/u-boot.bin\0" \
"update=protect off fffa0000 ffffffff;era fffa0000 ffffffff;" \
#define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */
#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */
#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */
+#define CFG_CONSOLE_INFO_QUIET 1 /* don't print console @ startup*/
/*-----------------------------------------------------------------------
* PCI stuff
#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
/*-----------------------------------------------------------------------
- * Cache Configuration
- *----------------------------------------------------------------------*/
-#define CFG_DCACHE_SIZE (16 << 10) /* For IBM 405EX */
-#define CFG_CACHELINE_SIZE 32
-#if defined(CONFIG_CMD_KGDB)
-#define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */
-#endif
-
-/*-----------------------------------------------------------------------
* External Bus Controller (EBC) Setup
*----------------------------------------------------------------------*/
/* Memory Bank 0 (NOR-FLASH) initialization */
-#define CFG_EBC_PB0AP 0x04011000
-#define CFG_EBC_PB0CR 0xFE0BA000 /* BAS=0xFE0,BS=32MB,BU=R/W,BW=16bit*/
+#define CFG_EBC_PB0AP 0x08033700
+#define CFG_EBC_PB0CR (CFG_FLASH_BASE | 0xda000)
/* Memory Bank 2 (CPLD) initialization */
#define CFG_EBC_PB2AP 0x9400C800
/*-----------------------------------------------------------------------
* GPIO Setup
*----------------------------------------------------------------------*/
-/*-----------------------------------------------------------------------
- * Definitions for GPIO setup (PPC405EX specific)
- *
- * GPIO0[0-3] - EBC data 0-3 inputs/outputs
- * GPIO0[4-7] - USB data 4-7 inputs/outputs
- * GPIO0[8-11] - NFCE# 1-3 inputs/outputs, GPIO11: IRQ6 inputs
- * GPIO0[12-15] - USB data 0-3 inputs/outputs
- * GPIO0[16-21] - UART0 control signal inputs/outputs
- *
- * GPIO0[22-25,27] - EBC control signal inputs/outputs
- * GPIO0[26] - Instruction trace outputs
- * GPIO0[28] - Float, N/C
- * GPIO0[29-31] - DMA control signal inputs/outputs
- */
-#define CFG_GPIO0_OSRL 0x00AA54AA
-#define CFG_GPIO0_OSRH 0x55500000
-#define CFG_GPIO0_TSRL 0x00AA54AA
-#define CFG_GPIO0_TSRH 0x55500000
-#define CFG_GPIO0_ISR1L 0x00005400
-#define CFG_GPIO0_ISR1H 0x55500000
-#define CFG_GPIO0_ISR2L 0x00550055
-#define CFG_GPIO0_ISR2H 0x00000000
+#define CFG_4xx_GPIO_TABLE { /* Out GPIO Alternate1 Alternate2 Alternate3 */ \
+{ \
+/* GPIO Core 0 */ \
+{GPIO0_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_0}, /* GPIO0 EBC_DATA_PAR(0) */ \
+{GPIO0_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_0}, /* GPIO1 EBC_DATA_PAR(1) */ \
+{GPIO0_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_0}, /* GPIO2 EBC_DATA_PAR(2) */ \
+{GPIO0_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_0}, /* GPIO3 EBC_DATA_PAR(3) */ \
+{GPIO0_BASE, GPIO_BI, GPIO_ALT2, GPIO_OUT_0}, /* GPIO4 EBC_DATA(20) USB2_DATA(4) */ \
+{GPIO0_BASE, GPIO_BI, GPIO_ALT2, GPIO_OUT_0}, /* GPIO5 EBC_DATA(21) USB2_DATA(5) */ \
+{GPIO0_BASE, GPIO_BI, GPIO_ALT2, GPIO_OUT_0}, /* GPIO6 EBC_DATA(22) USB2_DATA(6) */ \
+{GPIO0_BASE, GPIO_BI, GPIO_ALT2, GPIO_OUT_0}, /* GPIO7 EBC_DATA(23) USB2_DATA(7) */ \
+{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO8 CS(1)/NFCE(1) IRQ(7) */ \
+{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO9 CS(2)/NFCE(2) IRQ(8) */ \
+{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO10 CS(3)/NFCE(3) IRQ(9) */ \
+{GPIO0_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO11 IRQ(6) */ \
+{GPIO0_BASE, GPIO_BI, GPIO_ALT2, GPIO_OUT_0}, /* GPIO12 EBC_DATA(16) USB2_DATA(0) */ \
+{GPIO0_BASE, GPIO_BI, GPIO_ALT2, GPIO_OUT_0}, /* GPIO13 EBC_DATA(17) USB2_DATA(1) */ \
+{GPIO0_BASE, GPIO_BI, GPIO_ALT2, GPIO_OUT_0}, /* GPIO14 EBC_DATA(18) USB2_DATA(2) */ \
+{GPIO0_BASE, GPIO_BI, GPIO_ALT2, GPIO_OUT_0}, /* GPIO15 EBC_DATA(19) USB2_DATA(3) */ \
+{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO16 UART0_DCD UART1_CTS */ \
+{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO17 UART0_DSR UART1_RTS */ \
+{GPIO0_BASE, GPIO_IN, GPIO_ALT1, GPIO_OUT_0}, /* GPIO18 UART0_CTS */ \
+{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO19 UART0_RTS */ \
+{GPIO0_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_0}, /* GPIO20 UART0_DTR UART1_TX */ \
+{GPIO0_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_0}, /* GPIO21 UART0_RI UART1_RX */ \
+{GPIO0_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_0}, /* GPIO22 EBC_HOLD_REQ DMA_ACK2 */ \
+{GPIO0_BASE, GPIO_OUT, GPIO_SEL, GPIO_OUT_0}, /* GPIO23 EBC_HOLD_ACK DMA_REQ2 */ \
+{GPIO0_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_0}, /* GPIO24 EBC_EXT_REQ DMA_EOT2 IRQ(4) */ \
+{GPIO0_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_0}, /* GPIO25 EBC_EXT_ACK DMA_ACK3 IRQ(3) */ \
+{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO26 EBC_ADDR(5) DMA_EOT0 TS(3) */ \
+{GPIO0_BASE, GPIO_IN, GPIO_SEL , GPIO_OUT_0}, /* GPIO27 EBC_BUS_REQ DMA_EOT3 IRQ(5) */ \
+{GPIO0_BASE, GPIO_IN, GPIO_SEL , GPIO_OUT_0}, /* GPIO28 */ \
+{GPIO0_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_0}, /* GPIO29 DMA_EOT1 IRQ(2) */ \
+{GPIO0_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_0}, /* GPIO30 DMA_REQ1 IRQ(1) */ \
+{GPIO0_BASE, GPIO_IN, GPIO_ALT2, GPIO_OUT_0}, /* GPIO31 DMA_ACK1 IRQ(0) */ \
+} \
+}
+
+#define CFG_GPIO_PCIE_RST 23
+#define CFG_GPIO_PCIE_CLKREQ 27
+#define CFG_GPIO_PCIE_WAKE 28
/*
* Internal Definitions
#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
#define BOOTFLAG_WARM 0x02 /* Software reboot */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
#endif
#define CONFIG_OF_LIBFDT 1
#define CONFIG_OF_BOARD_SETUP 1
-#define OF_CPU "PowerPC,405EX@0"
-
#endif /* __CONFIG_H */
projects / platform / kernel / u-boot.git / blobdiff