/* SPDX-License-Identifier: GPL-2.0+ */
/*
- * Copyright 2018-2019 NXP
+ * Copyright 2018-2021 NXP
*/
#ifndef __LX2_COMMON_H
#define CONFIG_REMAKE_ELF
#define CONFIG_FSL_LAYERSCAPE
-#define CONFIG_GICV3
#define CONFIG_FSL_TZPC_BP147
#define CONFIG_FSL_MEMAC
#define CONFIG_SYS_INIT_SP_ADDR CONFIG_SYS_TEXT_BASE
#define CONFIG_SYS_FLASH_BASE 0x20000000
-#define CONFIG_SKIP_LOWLEVEL_INIT
-#define CONFIG_BOARD_EARLY_INIT_F 1
-
/* DDR */
#define CONFIG_FSL_DDR_INTERACTIVE /* Interactive debugging */
#define CONFIG_SYS_FSL_DDR_INTLV_256B /* force 256 byte interleaving */
#define CONFIG_SYS_DDR_BLOCK2_BASE 0x2080000000ULL
#define CONFIG_SYS_FSL_DDR_MAIN_NUM_CTRLS 2
#define CONFIG_SYS_SDRAM_SIZE 0x200000000UL
-#define CONFIG_DDR_SPD
-#define CONFIG_DDR_ECC
-#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER
#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE
#define CONFIG_MEM_INIT_VALUE 0xdeadbeef
#define SPD_EEPROM_ADDRESS1 0x51
#define CONFIG_SYS_MONITOR_LEN (936 * 1024)
/* Miscellaneous configurable options */
-#define CONFIG_SYS_LOAD_ADDR (CONFIG_SYS_DDR_SDRAM_BASE + 0x10000000)
/* SMP Definitinos */
-#define CPU_RELEASE_ADDR secondary_boot_func
+#define CPU_RELEASE_ADDR secondary_boot_addr
/* Generic Timer Definitions */
/*
(void *)CONFIG_SYS_SERIAL1, \
(void *)CONFIG_SYS_SERIAL2, \
(void *)CONFIG_SYS_SERIAL3 }
-#define CONFIG_BAUDRATE 115200
#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
/* MC firmware */
#define CONFIG_SYS_I2C_RTC_ADDR 0x51 /* Channel 3*/
/* EEPROM */
-#define CONFIG_ID_EEPROM
#define CONFIG_SYS_I2C_EEPROM_NXID
#define CONFIG_SYS_EEPROM_BUS_NUM 0
-#define CONFIG_SYS_I2C_EEPROM_ADDR 0x57
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5
/* Qixis */
#define CONFIG_FSL_QIXIS
#define CONFIG_PCI_SCAN_SHOW
#endif
-/* MMC */
-#ifdef CONFIG_MMC
-#define CONFIG_SYS_FSL_MMC_HAS_CAPBLT_VS33
-#endif
-
/* SATA */
#ifdef CONFIG_SCSI
#endif
/* USB */
-#ifdef CONFIG_USB
-#define CONFIG_HAS_FSL_XHCI_USB
+#ifdef CONFIG_USB_HOST
+#ifndef CONFIG_TARGET_LX2162AQDS
#define CONFIG_USB_MAX_CONTROLLER_COUNT 2
#endif
+#endif
-/* FlexSPI */
-#ifdef CONFIG_NXP_FSPI
-#define NXP_FSPI_FLASH_SIZE SZ_64M
-#define NXP_FSPI_FLASH_NUM 1
+/* GPIO */
+#ifdef CONFIG_DM_GPIO
+#ifndef CONFIG_MPC8XXX_GPIO
+#define CONFIG_MPC8XXX_GPIO
+#endif
#endif
#ifndef __ASSEMBLY__
unsigned long get_board_sys_clk(void);
-unsigned long get_board_ddr_clk(void);
#endif
#define CONFIG_SYS_CLK_FREQ get_board_sys_clk()
-#define CONFIG_DDR_CLK_FREQ get_board_ddr_clk()
#define COUNTER_FREQUENCY_REAL (CONFIG_SYS_CLK_FREQ / 4)
#define CONFIG_HWCONFIG
#define HWCONFIG_BUFFER_SIZE 128
-#define CONFIG_SYS_MMC_ENV_DEV 0
-#define CONFIG_ENV_SIZE 0x2000 /* 8KB */
-#define CONFIG_ENV_SECT_SIZE 0x20000
-#define CONFIG_ENV_OFFSET 0x500000
-#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + \
- CONFIG_ENV_OFFSET)
-
-/* Allow to overwrite serial and ethaddr */
-#define CONFIG_ENV_OVERWRITE
-
/* Monitor Command Prompt */
#define CONFIG_SYS_CBSIZE 512 /* Console I/O Buffer Size */
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \
#define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */
/* Initial environment variables */
-#define XSPI_MC_INIT_CMD \
- "env exists secureboot && " \
- "esbc_validate 0x20700000 && " \
- "esbc_validate 0x20740000 ;" \
- "fsl_mc start mc 0x20a00000 0x20e00000\0"
+#define XSPI_MC_INIT_CMD \
+ "sf probe 0:0 && " \
+ "sf read 0x80640000 0x640000 0x80000 && " \
+ "sf read $fdt_addr_r 0xf00000 0x100000 && " \
+ "env exists secureboot && " \
+ "esbc_validate 0x80640000 && " \
+ "esbc_validate 0x80680000; " \
+ "sf read 0x80a00000 0xa00000 0x300000 && " \
+ "sf read 0x80e00000 0xe00000 0x100000; " \
+ "fsl_mc start mc 0x80a00000 0x80e00000\0"
#define SD_MC_INIT_CMD \
"mmc read 0x80a00000 0x5000 0x1200;" \
"mmc read 0x80e00000 0x7000 0x800;" \
+ "mmc read $fdt_addr_r 0x7800 0x800;" \
"env exists secureboot && " \
- "mmc read 0x80700000 0x3800 0x10 && " \
- "mmc read 0x80740000 0x3A00 0x10 && " \
- "esbc_validate 0x80700000 && " \
- "esbc_validate 0x80740000 ;" \
+ "mmc read 0x80640000 0x3200 0x20 && " \
+ "mmc read 0x80680000 0x3400 0x20 && " \
+ "esbc_validate 0x80640000 && " \
+ "esbc_validate 0x80680000 ;" \
+ "fsl_mc start mc 0x80a00000 0x80e00000\0"
+
+#define SD2_MC_INIT_CMD \
+ "mmc dev 1; mmc read 0x80a00000 0x5000 0x1200;" \
+ "mmc read 0x80e00000 0x7000 0x800;" \
+ "mmc read $fdt_addr_r 0x7800 0x800;" \
+ "env exists secureboot && " \
+ "mmc read 0x80640000 0x3200 0x20 && " \
+ "mmc read 0x80680000 0x3400 0x20 && " \
+ "esbc_validate 0x80640000 && " \
+ "esbc_validate 0x80680000 ;" \
"fsl_mc start mc 0x80a00000 0x80e00000\0"
#define EXTRA_ENV_SETTINGS \
"initrd_high=0xffffffffffffffff\0" \
"fdt_addr=0x64f00000\0" \
"kernel_start=0x1000000\0" \
- "kernelheader_start=0x7C0000\0" \
+ "kernelheader_start=0x600000\0" \
"scriptaddr=0x80000000\0" \
"scripthdraddr=0x80080000\0" \
"fdtheader_addr_r=0x80100000\0" \
"load_addr=0xa0000000\0" \
"kernel_size=0x2800000\0" \
"kernel_addr_sd=0x8000\0" \
- "kernelhdr_addr_sd=0x3E00\0" \
- "kernel_size_sd=0x1d000\0" \
- "kernelhdr_size_sd=0x10\0" \
+ "kernelhdr_addr_sd=0x3000\0" \
+ "kernel_size_sd=0x14000\0" \
+ "kernelhdr_size_sd=0x20\0" \
"console=ttyAMA0,38400n8\0" \
BOOTENV \
"mcmemsize=0x70000000\0" \
XSPI_MC_INIT_CMD \
- "boot_scripts=lx2160ardb_boot.scr\0" \
- "boot_script_hdr=hdr_lx2160ardb_bs.out\0" \
"scan_dev_for_boot_part=" \
"part list ${devtype} ${devnum} devplist; " \
"env exists devplist || setenv devplist 1; " \
"source ${scriptaddr}\0"
#define XSPI_NOR_BOOTCOMMAND \
- "env exists mcinitcmd && env exists secureboot "\
- "&& esbc_validate 0x20780000; " \
+ "sf probe 0:0; " \
+ "sf read 0x806c0000 0x6c0000 0x40000; " \
+ "env exists mcinitcmd && env exists secureboot" \
+ " && esbc_validate 0x806c0000; " \
+ "sf read 0x80d00000 0xd00000 0x100000; " \
"env exists mcinitcmd && " \
- "fsl_mc lazyapply dpl 0x20d00000; " \
+ "fsl_mc lazyapply dpl 0x80d00000; " \
"run distro_bootcmd;run xspi_bootcmd; " \
"env exists secureboot && esbc_halt;"
"env exists mcinitcmd && mmcinfo; " \
"mmc read 0x80d00000 0x6800 0x800; " \
"env exists mcinitcmd && env exists secureboot " \
- " && mmc read 0x80780000 0x3C00 0x10 " \
- "&& esbc_validate 0x80780000;env exists mcinitcmd " \
+ " && mmc read 0x806C0000 0x3600 0x20 " \
+ "&& esbc_validate 0x806C0000;env exists mcinitcmd " \
"&& fsl_mc lazyapply dpl 0x80d00000;" \
"run distro_bootcmd;run sd_bootcmd;" \
"env exists secureboot && esbc_halt;"
+#define SD2_BOOTCOMMAND \
+ "mmc dev 1; env exists mcinitcmd && mmcinfo; " \
+ "mmc read 0x80d00000 0x6800 0x800; " \
+ "env exists mcinitcmd && env exists secureboot " \
+ " && mmc read 0x806C0000 0x3600 0x20 " \
+ "&& esbc_validate 0x806C0000;env exists mcinitcmd " \
+ "&& fsl_mc lazyapply dpl 0x80d00000;" \
+ "run distro_bootcmd;run sd2_bootcmd;" \
+ "env exists secureboot && esbc_halt;"
+
#define BOOT_TARGET_DEVICES(func) \
func(USB, usb, 0) \
func(MMC, mmc, 0) \
- func(SCSI, scsi, 0)
+ func(MMC, mmc, 1) \
+ func(SCSI, scsi, 0) \
+ func(DHCP, dhcp, na)
#include <config_distro_bootcmd.h>
#endif /* __LX2_COMMON_H */
projects / platform / kernel / u-boot.git / blobdiff