#define __CONFIG_H
/*
- * If we are developing, we might want to start armboot from ram
- * so we MUST NOT initialize critical regs like mem-timing ...
- */
-#define CONFIG_INIT_CRITICAL
-
-/*
* High Level Configuration Options
* (easy to change)
*/
#endif
#define CONFIG_MMC 1
#define BOARD_LATE_INIT 1
+#define CONFIG_DOS_PARTITION
#undef CONFIG_USE_IRQ /* we don't need IRQ/FIQ stuff */
#define CONFIG_BAUDRATE 115200
-#define CONFIG_COMMANDS (CONFIG_CMD_DFL | CFG_CMD_MMC | CFG_CMD_FAT)
-/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
-#include <cmd_confdefs.h>
+/*
+ * BOOTP options
+ */
+#define CONFIG_BOOTP_BOOTFILESIZE
+#define CONFIG_BOOTP_BOOTPATH
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_HOSTNAME
+
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_MMC
+#define CONFIG_CMD_FAT
+
#define CONFIG_BOOTDELAY 3
#define CONFIG_ETHADDR 08:00:3e:26:0a:5b
#define CONFIG_NETMASK 255.255.0.0
#define CONFIG_IPADDR 192.168.0.21
#define CONFIG_SERVERIP 192.168.0.250
-#define CONFIG_BOOTCOMMAND "bootm 40000"
+#define CONFIG_BOOTCOMMAND "bootm 80000"
#define CONFIG_BOOTARGS "root=/dev/mtdblock2 rootfstype=cramfs console=ttyS0,115200"
#define CONFIG_CMDLINE_TAG
+#define CONFIG_TIMESTAMP
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
#endif
#undef CFG_CLKS_IN_HZ /* everything, incl board info, in Hz */
-#define CFG_LOAD_ADDR 0xa8000000 /* default load address */
+#define CFG_LOAD_ADDR (CFG_DRAM_BASE + 0x8000) /* default load address */
#define CFG_HZ 3686400 /* incrementer freq: 3.6864 MHz */
#define CFG_CPUSPEED 0x161 /* set core clock to 400/200/100 MHz */
#define CFG_FLASH_ERASE_TOUT (25*CFG_HZ) /* Timeout for Flash Erase */
#define CFG_FLASH_WRITE_TOUT (25*CFG_HZ) /* Timeout for Flash Write */
-/* FIXME */
+/* NOTE: many default partitioning schemes assume the kernel starts at the
+ * second sector, not an environment. You have been warned!
+ */
+#define CFG_MONITOR_LEN PHYS_FLASH_SECT_SIZE
#define CFG_ENV_IS_IN_FLASH 1
-#define CFG_ENV_ADDR (PHYS_FLASH_1 + 0x1C000) /* Addr of Environment Sector */
-#define CFG_ENV_SIZE 0x4000 /* Total Size of Environment Sector */
+#define CFG_ENV_ADDR (PHYS_FLASH_1 + PHYS_FLASH_SECT_SIZE)
+#define CFG_ENV_SECT_SIZE PHYS_FLASH_SECT_SIZE
+#define CFG_ENV_SIZE (PHYS_FLASH_SECT_SIZE / 16)
/*