#define CONFIG_ARM_ERRATA_828024
#define CONFIG_ARM_ERRATA_826974
+#include <asm/arch-fsl-lsch3/config.h>
+#if (defined(CONFIG_SYS_FSL_SRDS_1) || defined(CONFIG_SYS_FSL_SRDS_2))
+#define CONFIG_SYS_HAS_SERDES
+#endif
+
/* We need architecture specific misc initializations */
#define CONFIG_ARCH_MISC_INIT
/* Link Definitions */
+#ifdef CONFIG_SPL
+#define CONFIG_SYS_TEXT_BASE 0x80400000
+#else
#define CONFIG_SYS_TEXT_BASE 0x30100000
+#endif
#ifdef CONFIG_EMU
#define CONFIG_SYS_NO_FLASH
#define CONFIG_FIT
#define CONFIG_FIT_VERBOSE /* enable fit_format_{error,warning}() */
+#ifndef CONFIG_SPL
#define CONFIG_FSL_DDR_INTERACTIVE /* Interactive debugging */
+#endif
#ifndef CONFIG_SYS_FSL_DDR4
#define CONFIG_SYS_FSL_DDR3 /* Use DDR3 memory */
#define CONFIG_SYS_DDR_RAW_TIMING
#define CONFIG_SYS_I2C_MXC_I2C4 /* enable I2C bus 4 */
/* Serial Port */
-#define CONFIG_CONS_INDEX 2
+#define CONFIG_CONS_INDEX 1
#define CONFIG_SYS_NS16550
#define CONFIG_SYS_NS16550_SERIAL
#define CONFIG_SYS_NS16550_REG_SIZE 1
#define CONFIG_FSL_IFC
/*
- * During booting, CS0 needs to be at the region of 0x30000000, i.e. the IFC
- * address 0. But this region is limited to 256MB. To accommodate bigger NOR
- * flash and other devices, we will map CS0 to 0x580000000 after relocation.
+ * During booting, IFC is mapped at the region of 0x30000000.
+ * But this region is limited to 256MB. To accommodate NOR, promjet
+ * and FPGA. This region is divided as below:
+ * 0x30000000 - 0x37ffffff : 128MB : NOR flash
+ * 0x38000000 - 0x3BFFFFFF : 64MB : Promjet
+ * 0x3C000000 - 0x40000000 : 64MB : FPGA etc
+ *
+ * To accommodate bigger NOR flash and other devices, we will map IFC
+ * chip selects to as below:
+ * 0x5_1000_0000..0x5_1fff_ffff Memory Hole
+ * 0x5_2000_0000..0x5_3fff_ffff IFC CSx (FPGA, NAND and others 512MB)
+ * 0x5_4000_0000..0x5_7fff_ffff ASIC or others 1GB
+ * 0x5_8000_0000..0x5_bfff_ffff IFC CS0 1GB (NOR/Promjet)
+ * 0x5_C000_0000..0x5_ffff_ffff IFC CS1 1GB (NOR/Promjet)
+ *
+ * For e.g. NOR flash at CS0 will be mapped to 0x580000000 after relocation.
* CONFIG_SYS_FLASH_BASE has the final address (core view)
* CONFIG_SYS_FLASH_BASE_PHYS has the final address (IFC view)
* CONFIG_SYS_FLASH_BASE_PHYS_EARLY has the temporary IFC address
* CONFIG_SYS_TEXT_BASE is linked to 0x30000000 for booting
*/
+
#define CONFIG_SYS_FLASH_BASE 0x580000000ULL
#define CONFIG_SYS_FLASH_BASE_PHYS 0x80000000
#define CONFIG_SYS_FLASH_BASE_PHYS_EARLY 0x00000000
+#define CONFIG_SYS_FLASH1_BASE_PHYS 0xC0000000
+#define CONFIG_SYS_FLASH1_BASE_PHYS_EARLY 0x8000000
+
#ifndef CONFIG_SYS_NO_FLASH
#define CONFIG_FLASH_CFI_DRIVER
#define CONFIG_SYS_FLASH_CFI
#define CONFIG_SYS_FLASH_QUIET_TEST
#endif
-#define CONFIG_SYS_NAND_BASE 0x520000000
-#define CONFIG_SYS_NAND_BASE_PHYS 0x20000000
+#ifndef __ASSEMBLY__
+unsigned long long get_qixis_addr(void);
+#endif
+#define QIXIS_BASE get_qixis_addr()
+#define QIXIS_BASE_PHYS 0x20000000
+#define QIXIS_BASE_PHYS_EARLY 0xC000000
+#define QIXIS_STAT_PRES1 0xb
+#define QIXIS_SDID_MASK 0x07
+#define QIXIS_ESDHC_NO_ADAPTER 0x7
+
+#define CONFIG_SYS_NAND_BASE 0x530000000ULL
+#define CONFIG_SYS_NAND_BASE_PHYS 0x30000000
/* Debug Server firmware */
#define CONFIG_SYS_DEBUG_SERVER_DRAM_BLOCK_MIN_SIZE (512UL * 1024 * 1024)
#define CONFIG_FSL_MC_ENET
#define CONFIG_SYS_LS_MC_DRAM_BLOCK_MIN_SIZE (512UL * 1024 * 1024)
/* TODO Actual DPL max length needs to be confirmed with the MC FW team */
-#define CONFIG_SYS_LS_MC_DPL_MAX_LENGTH (256 * 1024)
-#define CONFIG_SYS_LS_MC_DRAM_DPL_OFFSET 0xe00000
+#define CONFIG_SYS_LS_MC_DPC_MAX_LENGTH 0x20000
+#define CONFIG_SYS_LS_MC_DRAM_DPC_OFFSET 0x00F00000
+#define CONFIG_SYS_LS_MC_DPL_MAX_LENGTH 0x20000
+#define CONFIG_SYS_LS_MC_DRAM_DPL_OFFSET 0x00F20000
/* Carve out a DDR region which will not be used by u-boot/Linux */
#if defined(CONFIG_FSL_MC_ENET) || defined(CONFIG_FSL_DEBUG_SERVER)
#define CONFIG_CMD_BOOTD
#define CONFIG_CMD_ECHO
#define CONFIG_CMD_SOURCE
-#define CONFIG_CMD_FAT
-#define CONFIG_DOS_PARTITION
/* Miscellaneous configurable options */
#define CONFIG_SYS_LOAD_ADDR (CONFIG_SYS_DDR_SDRAM_BASE + 0x10000000)
"hugepages=16"
#define CONFIG_BOOTCOMMAND "cp.b $kernel_start $kernel_load " \
"$kernel_size && bootm $kernel_load"
-#define CONFIG_BOOTDELAY 1
+#define CONFIG_BOOTDELAY 10
/* Monitor Command Prompt */
#define CONFIG_SYS_CBSIZE 512 /* Console I/O Buffer Size */
#define CONFIG_PANIC_HANG /* do not reset board on panic */
+#define CONFIG_SPL_BSS_START_ADDR 0x80100000
+#define CONFIG_SPL_BSS_MAX_SIZE 0x00100000
+#define CONFIG_SPL_DRIVERS_MISC_SUPPORT
+#define CONFIG_SPL_ENV_SUPPORT
+#define CONFIG_SPL_FRAMEWORK
+#define CONFIG_SPL_I2C_SUPPORT
+#define CONFIG_SPL_LDSCRIPT "arch/arm/cpu/armv8/u-boot-spl.lds"
+#define CONFIG_SPL_LIBCOMMON_SUPPORT
+#define CONFIG_SPL_LIBGENERIC_SUPPORT
+#define CONFIG_SPL_MAX_SIZE 0x16000
+#define CONFIG_SPL_MPC8XXX_INIT_DDR_SUPPORT
+#define CONFIG_SPL_NAND_SUPPORT
+#define CONFIG_SPL_SERIAL_SUPPORT
+#define CONFIG_SPL_STACK (CONFIG_SYS_FSL_OCRAM_BASE + 0x9ff0)
+#define CONFIG_SPL_TARGET "u-boot-with-spl.bin"
+#define CONFIG_SPL_TEXT_BASE 0x1800a000
+
+#define CONFIG_SYS_NAND_U_BOOT_DST 0x80400000
+#define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_NAND_U_BOOT_DST
+#define CONFIG_SYS_SPL_MALLOC_SIZE 0x00100000
+#define CONFIG_SYS_SPL_MALLOC_START 0x80200000
+#define CONFIG_SYS_MONITOR_LEN (512 * 1024)
+
#endif /* __LS2_COMMON_H */
projects / platform / kernel / u-boot.git / blobdiff