#include "ls2080a_common.h"
-#ifndef __ASSEMBLY__
-unsigned long get_board_sys_clk(void);
-#endif
-
#ifdef CONFIG_FSL_QSPI
-#define CONFIG_QIXIS_I2C_ACCESS
#define CONFIG_SYS_I2C_IFDR_DIV 0x7e
#endif
#define CONFIG_SYS_I2C_FPGA_ADDR 0x66
-#define CONFIG_SYS_CLK_FREQ get_board_sys_clk()
-#define COUNTER_FREQUENCY_REAL (CONFIG_SYS_CLK_FREQ/4)
+#define COUNTER_FREQUENCY_REAL (get_board_sys_clk()/4)
#define CONFIG_MEM_INIT_VALUE 0xdeadbeef
#define SPD_EEPROM_ADDRESS1 0x51
#define SPD_EEPROM_ADDRESS5 0x55
#define SPD_EEPROM_ADDRESS6 0x56 /* dummy address */
#define SPD_EEPROM_ADDRESS SPD_EEPROM_ADDRESS1
-#define CONFIG_SYS_SPD_BUS_NUM 0 /* SPD on I2C bus 0 */
-#define CONFIG_DIMM_SLOTS_PER_CTLR 2
-#define CONFIG_CHIP_SELECTS_PER_CTRL 4
-#ifdef CONFIG_SYS_FSL_HAS_DP_DDR
-#define CONFIG_DP_DDR_DIMM_SLOTS_PER_CTLR 1
-#endif
-
-/* SATA */
-#define CONFIG_SCSI_AHCI_PLAT
-
-#define CONFIG_SYS_SATA1 AHCI_BASE_ADDR1
-#define CONFIG_SYS_SATA2 AHCI_BASE_ADDR2
-
-#define CONFIG_SYS_SCSI_MAX_SCSI_ID 1
-#define CONFIG_SYS_SCSI_MAX_LUN 1
-#define CONFIG_SYS_SCSI_MAX_DEVICE (CONFIG_SYS_SCSI_MAX_SCSI_ID * \
- CONFIG_SYS_SCSI_MAX_LUN)
#define CONFIG_SYS_NOR0_CSPR_EXT (0x0)
#define CONFIG_SYS_NOR_AMASK IFC_AMASK(128*1024*1024)
#define CONFIG_SYS_IFC_CCR 0x01000000
#ifdef CONFIG_MTD_NOR_FLASH
-#define CONFIG_SYS_FLASH_QUIET_TEST
#define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */
-#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* number of banks */
-#define CONFIG_SYS_MAX_FLASH_SECT 1024 /* sectors per device */
-#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
-#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
-
-#define CONFIG_SYS_FLASH_EMPTY_INFO
#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE,\
CONFIG_SYS_FLASH_BASE + 0x40000000}
#endif
-#define CONFIG_SYS_NAND_MAX_ECCPOS 256
-#define CONFIG_SYS_NAND_MAX_OOBFREE 2
-
-#define CONFIG_SYS_NAND_CSPR_EXT (0x0)
-#define CONFIG_SYS_NAND_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \
+#define CFG_SYS_NAND_CSPR_EXT (0x0)
+#define CFG_SYS_NAND_CSPR (CSPR_PHYS_ADDR(CFG_SYS_NAND_BASE_PHYS) \
| CSPR_PORT_SIZE_8 /* Port Size = 8 bit */ \
| CSPR_MSEL_NAND /* MSEL = NAND */ \
| CSPR_V)
-#define CONFIG_SYS_NAND_AMASK IFC_AMASK(64 * 1024)
+#define CFG_SYS_NAND_AMASK IFC_AMASK(64 * 1024)
-#define CONFIG_SYS_NAND_CSOR (CSOR_NAND_ECC_ENC_EN /* ECC on encode */ \
+#define CFG_SYS_NAND_CSOR (CSOR_NAND_ECC_ENC_EN /* ECC on encode */ \
| CSOR_NAND_ECC_DEC_EN /* ECC on decode */ \
| CSOR_NAND_ECC_MODE_4 /* 4-bit ECC */ \
| CSOR_NAND_RAL_3 /* RAL = 3Byes */ \
| CSOR_NAND_PB(64)) /*Pages Per Block = 64*/
/* ONFI NAND Flash mode0 Timing Params */
-#define CONFIG_SYS_NAND_FTIM0 (FTIM0_NAND_TCCST(0x07) | \
+#define CFG_SYS_NAND_FTIM0 (FTIM0_NAND_TCCST(0x07) | \
FTIM0_NAND_TWP(0x18) | \
FTIM0_NAND_TWCHT(0x07) | \
FTIM0_NAND_TWH(0x0a))
-#define CONFIG_SYS_NAND_FTIM1 (FTIM1_NAND_TADLE(0x32) | \
+#define CFG_SYS_NAND_FTIM1 (FTIM1_NAND_TADLE(0x32) | \
FTIM1_NAND_TWBE(0x39) | \
FTIM1_NAND_TRR(0x0e) | \
FTIM1_NAND_TRP(0x18))
-#define CONFIG_SYS_NAND_FTIM2 (FTIM2_NAND_TRAD(0x0f) | \
+#define CFG_SYS_NAND_FTIM2 (FTIM2_NAND_TRAD(0x0f) | \
FTIM2_NAND_TREH(0x0a) | \
FTIM2_NAND_TWHRE(0x1e))
-#define CONFIG_SYS_NAND_FTIM3 0x0
+#define CFG_SYS_NAND_FTIM3 0x0
-#define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND_BASE }
-#define CONFIG_SYS_MAX_NAND_DEVICE 1
+#define CFG_SYS_NAND_BASE_LIST { CFG_SYS_NAND_BASE }
#define CONFIG_MTD_NAND_VERIFY_WRITE
-#define CONFIG_FSL_QIXIS /* use common QIXIS code */
#define QIXIS_LBMAP_SWITCH 0x06
#define QIXIS_LBMAP_MASK 0x0f
#define QIXIS_LBMAP_SHIFT 0
#define CONFIG_SYS_CS2_FTIM1 CONFIG_SYS_NOR_FTIM1
#define CONFIG_SYS_CS2_FTIM2 CONFIG_SYS_NOR_FTIM2
#define CONFIG_SYS_CS2_FTIM3 CONFIG_SYS_NOR_FTIM3
-#define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_NAND_CSPR_EXT
-#define CONFIG_SYS_CSPR0 CONFIG_SYS_NAND_CSPR
-#define CONFIG_SYS_AMASK0 CONFIG_SYS_NAND_AMASK
-#define CONFIG_SYS_CSOR0 CONFIG_SYS_NAND_CSOR
-#define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NAND_FTIM0
-#define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NAND_FTIM1
-#define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NAND_FTIM2
-#define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NAND_FTIM3
-
-#define CONFIG_SPL_PAD_TO 0x20000
-#define CONFIG_SYS_NAND_U_BOOT_SIZE (640 * 1024)
+#define CONFIG_SYS_CSPR0_EXT CFG_SYS_NAND_CSPR_EXT
+#define CONFIG_SYS_CSPR0 CFG_SYS_NAND_CSPR
+#define CONFIG_SYS_AMASK0 CFG_SYS_NAND_AMASK
+#define CONFIG_SYS_CSOR0 CFG_SYS_NAND_CSOR
+#define CONFIG_SYS_CS0_FTIM0 CFG_SYS_NAND_FTIM0
+#define CONFIG_SYS_CS0_FTIM1 CFG_SYS_NAND_FTIM1
+#define CONFIG_SYS_CS0_FTIM2 CFG_SYS_NAND_FTIM2
+#define CONFIG_SYS_CS0_FTIM3 CFG_SYS_NAND_FTIM3
+
+#define CFG_SYS_NAND_U_BOOT_SIZE (640 * 1024)
#endif
#else
#define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_NOR0_CSPR_EXT
#define CONFIG_SYS_CS1_FTIM1 CONFIG_SYS_NOR_FTIM1
#define CONFIG_SYS_CS1_FTIM2 CONFIG_SYS_NOR_FTIM2
#define CONFIG_SYS_CS1_FTIM3 CONFIG_SYS_NOR_FTIM3
-#define CONFIG_SYS_CSPR2_EXT CONFIG_SYS_NAND_CSPR_EXT
-#define CONFIG_SYS_CSPR2 CONFIG_SYS_NAND_CSPR
-#define CONFIG_SYS_AMASK2 CONFIG_SYS_NAND_AMASK
-#define CONFIG_SYS_CSOR2 CONFIG_SYS_NAND_CSOR
-#define CONFIG_SYS_CS2_FTIM0 CONFIG_SYS_NAND_FTIM0
-#define CONFIG_SYS_CS2_FTIM1 CONFIG_SYS_NAND_FTIM1
-#define CONFIG_SYS_CS2_FTIM2 CONFIG_SYS_NAND_FTIM2
-#define CONFIG_SYS_CS2_FTIM3 CONFIG_SYS_NAND_FTIM3
+#define CONFIG_SYS_CSPR2_EXT CFG_SYS_NAND_CSPR_EXT
+#define CONFIG_SYS_CSPR2 CFG_SYS_NAND_CSPR
+#define CONFIG_SYS_AMASK2 CFG_SYS_NAND_AMASK
+#define CONFIG_SYS_CSOR2 CFG_SYS_NAND_CSOR
+#define CONFIG_SYS_CS2_FTIM0 CFG_SYS_NAND_FTIM0
+#define CONFIG_SYS_CS2_FTIM1 CFG_SYS_NAND_FTIM1
+#define CONFIG_SYS_CS2_FTIM2 CFG_SYS_NAND_FTIM2
+#define CONFIG_SYS_CS2_FTIM3 CFG_SYS_NAND_FTIM3
#endif
-/* Debug Server firmware */
-#define CONFIG_SYS_DEBUG_SERVER_FW_IN_NOR
-#define CONFIG_SYS_DEBUG_SERVER_FW_ADDR 0x580D00000ULL
-
#define CONFIG_SYS_LS_MC_BOOT_TIMEOUT_MS 5000
/*
#define I2C_MUX_CH_DEFAULT 0x8
/* SPI */
-#ifdef CONFIG_FSL_DSPI
-#define CONFIG_SPI_FLASH_STMICRO
-#define CONFIG_SPI_FLASH_SST
-#define CONFIG_SPI_FLASH_EON
-#endif
-#ifdef CONFIG_FSL_QSPI
-#define CONFIG_SPI_FLASH_SPANSION
-#endif
/*
* Verify QSPI when boot from NAND, QIXIS brdcfg9 need configure.
* If boot from on-board NAND, ISO1 = 1, ISO2 = 0, IBOOT = 0
#define FSL_QIXIS_BRDCFG9_QSPI 0x1
/*
- * MMC
- */
-#ifdef CONFIG_MMC
-#define CONFIG_ESDHC_DETECT_QUIRK ((readb(QIXIS_BASE + QIXIS_STAT_PRES1) & \
- QIXIS_SDID_MASK) != QIXIS_ESDHC_NO_ADAPTER)
-#endif
-
-/*
* RTC configuration
*/
#define RTC
#define CONFIG_RTC_DS3231 1
-#define CONFIG_RTC_ENABLE_32KHZ_OUTPUT
#define CONFIG_SYS_I2C_RTC_ADDR 0x68
-#define CONFIG_RTC_ENABLE_32KHZ_OUTPUT
-
-/* EEPROM */
-#define CONFIG_SYS_I2C_EEPROM_NXID
-#define CONFIG_SYS_EEPROM_BUS_NUM 0
-
-#define CONFIG_FSL_MEMAC
-
-#ifdef CONFIG_PCI
-#define CONFIG_PCI_SCAN_SHOW
-#endif
/* Initial environment variables */
#undef CONFIG_EXTRA_ENV_SETTINGS
"env exists secureboot && esbc_halt;"
#endif
-#if defined(CONFIG_FSL_MC_ENET) && !defined(CONFIG_SPL_BUILD)
-#define CONFIG_FSL_MEMAC
+#if defined(CONFIG_FSL_MC_ENET)
#define SGMII_CARD_PORT1_PHY_ADDR 0x1C
#define SGMII_CARD_PORT2_PHY_ADDR 0x1d
#define SGMII_CARD_PORT3_PHY_ADDR 0x1E
#define XQSGMII_CARD_PHY4_PORT2_ADDR 0xe
#define XQSGMII_CARD_PHY4_PORT3_ADDR 0xf
-#define CONFIG_ETHPRIME "DPMAC1@xgmii"
-
#endif
#include <asm/fsl_secure_boot.h>
projects / platform / kernel / u-boot.git / blobdiff