/* SPDX-License-Identifier: GPL-2.0+ */
/*
- * Copyright 2017, 2019 NXP
+ * Copyright 2017, 2019-2021 NXP
* Copyright 2015 Freescale Semiconductor
*/
#include "ls2080a_common.h"
-#ifndef __ASSEMBLY__
-unsigned long get_board_sys_clk(void);
-unsigned long get_board_ddr_clk(void);
-#endif
-
#ifdef CONFIG_FSL_QSPI
#define CONFIG_QIXIS_I2C_ACCESS
-#ifndef CONFIG_DM_I2C
-#define CONFIG_SYS_I2C_EARLY_INIT
-#endif
#define CONFIG_SYS_I2C_IFDR_DIV 0x7e
#endif
#define CONFIG_SYS_I2C_FPGA_ADDR 0x66
-#define CONFIG_SYS_CLK_FREQ get_board_sys_clk()
-#define CONFIG_DDR_CLK_FREQ get_board_ddr_clk()
-#define COUNTER_FREQUENCY_REAL (CONFIG_SYS_CLK_FREQ/4)
+#define COUNTER_FREQUENCY_REAL (get_board_sys_clk()/4)
-#define CONFIG_DDR_SPD
-#define CONFIG_DDR_ECC
-#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER
#define CONFIG_MEM_INIT_VALUE 0xdeadbeef
#define SPD_EEPROM_ADDRESS1 0x51
#define SPD_EEPROM_ADDRESS2 0x52
#define CONFIG_SYS_SCSI_MAX_DEVICE (CONFIG_SYS_SCSI_MAX_SCSI_ID * \
CONFIG_SYS_SCSI_MAX_LUN)
-#ifdef CONFIG_TFABOOT
-#define CONFIG_SYS_MMC_ENV_DEV 0
-#define CONFIG_ENV_SIZE 0x20000
-#define CONFIG_ENV_OFFSET 0x500000
-#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + \
- CONFIG_ENV_OFFSET)
-#define CONFIG_ENV_SECT_SIZE 0x20000
-#endif
-
#define CONFIG_SYS_NOR0_CSPR_EXT (0x0)
#define CONFIG_SYS_NOR_AMASK IFC_AMASK(128*1024*1024)
#define CONFIG_SYS_NOR_AMASK_EARLY IFC_AMASK(64*1024*1024)
#define CONFIG_SYS_FLASH_QUIET_TEST
#define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */
-#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* number of banks */
#define CONFIG_SYS_MAX_FLASH_SECT 1024 /* sectors per device */
#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
CONFIG_SYS_FLASH_BASE + 0x40000000}
#endif
-#define CONFIG_NAND_FSL_IFC
#define CONFIG_SYS_NAND_MAX_ECCPOS 256
#define CONFIG_SYS_NAND_MAX_OOBFREE 2
| CSOR_NAND_SPRZ_64/* Spare size = 64 */ \
| CSOR_NAND_PB(64)) /*Pages Per Block = 64*/
-#define CONFIG_SYS_NAND_ONFI_DETECTION
-
/* ONFI NAND Flash mode0 Timing Params */
#define CONFIG_SYS_NAND_FTIM0 (FTIM0_NAND_TCCST(0x07) | \
FTIM0_NAND_TWP(0x18) | \
#define CONFIG_SYS_MAX_NAND_DEVICE 1
#define CONFIG_MTD_NAND_VERIFY_WRITE
-#define CONFIG_SYS_NAND_BLOCK_SIZE (128 * 1024)
-
#define CONFIG_FSL_QIXIS /* use common QIXIS code */
#define QIXIS_LBMAP_SWITCH 0x06
#define QIXIS_LBMAP_MASK 0x0f
#define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NAND_FTIM2
#define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NAND_FTIM3
-#define CONFIG_ENV_OFFSET (896 * 1024)
-#define CONFIG_ENV_SECT_SIZE 0x20000
-#define CONFIG_ENV_SIZE 0x2000
#define CONFIG_SPL_PAD_TO 0x20000
-#define CONFIG_SYS_NAND_U_BOOT_OFFS (256 * 1024)
#define CONFIG_SYS_NAND_U_BOOT_SIZE (640 * 1024)
-#elif defined(CONFIG_SD_BOOT)
-#define CONFIG_ENV_OFFSET 0x300000
-#define CONFIG_SYS_MMC_ENV_DEV 0
-#define CONFIG_ENV_SIZE 0x20000
#endif
#else
#define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_NOR0_CSPR_EXT
#define CONFIG_SYS_CS2_FTIM1 CONFIG_SYS_NAND_FTIM1
#define CONFIG_SYS_CS2_FTIM2 CONFIG_SYS_NAND_FTIM2
#define CONFIG_SYS_CS2_FTIM3 CONFIG_SYS_NAND_FTIM3
-
-#if !defined(CONFIG_QSPI_BOOT) && !defined(CONFIG_TFABOOT)
-#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x300000)
-#define CONFIG_ENV_SECT_SIZE 0x20000
-#define CONFIG_ENV_SIZE 0x2000
-#endif
#endif
/* Debug Server firmware */
#define I2C_MUX_CH_DEFAULT 0x8
/* SPI */
-#if defined(CONFIG_FSL_QSPI) || defined(CONFIG_FSL_DSPI)
-#ifdef CONFIG_FSL_DSPI
-#define CONFIG_SPI_FLASH_STMICRO
-#define CONFIG_SPI_FLASH_SST
-#define CONFIG_SPI_FLASH_EON
-#endif
-#ifdef CONFIG_FSL_QSPI
-#define CONFIG_SPI_FLASH_SPANSION
-#define FSL_QSPI_FLASH_SIZE (1 << 26) /* 64MB */
-#define FSL_QSPI_FLASH_NUM 4
-#endif
/*
* Verify QSPI when boot from NAND, QIXIS brdcfg9 need configure.
* If boot from on-board NAND, ISO1 = 1, ISO2 = 0, IBOOT = 0
*/
#define FSL_QIXIS_BRDCFG9_QSPI 0x1
-#endif
-
/*
* MMC
*/
*/
#define RTC
#define CONFIG_RTC_DS3231 1
-#define CONFIG_RTC_ENABLE_32KHZ_OUTPUT
#define CONFIG_SYS_I2C_RTC_ADDR 0x68
-#define CONFIG_RTC_ENABLE_32KHZ_OUTPUT
/* EEPROM */
-#define CONFIG_ID_EEPROM
#define CONFIG_SYS_I2C_EEPROM_NXID
#define CONFIG_SYS_EEPROM_BUS_NUM 0
-#define CONFIG_SYS_I2C_EEPROM_ADDR 0x57
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5
#define CONFIG_FSL_MEMAC
#define CONFIG_PCI_SCAN_SHOW
#endif
-/* MMC */
-#ifdef CONFIG_MMC
-#define CONFIG_SYS_FSL_MMC_HAS_CAPBLT_VS33
-#endif
-
/* Initial environment variables */
#undef CONFIG_EXTRA_ENV_SETTINGS
#ifdef CONFIG_NXP_ESBC
"kernel_load=0xa0000000\0" \
"kernel_size=0x2800000\0" \
"mcmemsize=0x40000000\0" \
- "mcinitcmd=esbc_validate 0x580700000;" \
- "esbc_validate 0x580740000;" \
+ "mcinitcmd=esbc_validate 0x580640000;" \
+ "esbc_validate 0x580680000;" \
"fsl_mc start mc 0x580a00000" \
" 0x580e00000 \0"
#else
#ifdef CONFIG_TFABOOT
#define SD_MC_INIT_CMD \
- "mmcinfo;mmc read 0x80a00000 0x5000 0x1200;" \
+ "mmcinfo;mmc read 0x80a00000 0x5000 0x1000;" \
"mmc read 0x80e00000 0x7000 0x800;" \
"fsl_mc start mc 0x80a00000 0x80e00000\0"
#define IFC_MC_INIT_CMD \
"kernel_size=0x2800000\0" \
"kernel_size_sd=0x14000\0" \
"load_addr=0xa0000000\0" \
- "kernelheader_addr=0x580800000\0" \
+ "kernelheader_addr=0x580600000\0" \
"kernelheader_addr_r=0x80200000\0" \
"kernelheader_size=0x40000\0" \
"BOARD=ls2088aqds\0" \
"mcmemsize=0x70000000 \0" \
+ "scriptaddr=0x80000000\0" \
+ "scripthdraddr=0x80080000\0" \
IFC_MC_INIT_CMD \
+ BOOTENV \
+ "boot_scripts=ls2088aqds_boot.scr\0" \
+ "boot_script_hdr=hdr_ls2088aqds_bs.out\0" \
+ "scan_dev_for_boot_part=" \
+ "part list ${devtype} ${devnum} devplist; " \
+ "env exists devplist || setenv devplist 1; " \
+ "for distro_bootpart in ${devplist}; do " \
+ "if fstype ${devtype} " \
+ "${devnum}:${distro_bootpart} " \
+ "bootfstype; then " \
+ "run scan_dev_for_boot; " \
+ "fi; " \
+ "done\0" \
+ "boot_a_script=" \
+ "load ${devtype} ${devnum}:${distro_bootpart} " \
+ "${scriptaddr} ${prefix}${script}; " \
+ "env exists secureboot && load ${devtype} " \
+ "${devnum}:${distro_bootpart} " \
+ "${scripthdraddr} ${prefix}${boot_script_hdr} " \
+ "&& esbc_validate ${scripthdraddr};" \
+ "source ${scriptaddr}\0" \
"nor_bootcmd=echo Trying load from nor..;" \
"cp.b $kernel_addr $load_addr " \
"$kernel_size ; env exists secureboot && " \
"kernel_start=0x8000\0" \
"kernel_load=0xa0000000\0" \
"kernel_size=0x14000\0" \
- "mcinitcmd=mmcinfo;mmc read 0x80000000 0x5000 0x800;" \
- "mmc read 0x80100000 0x7000 0x800;" \
- "fsl_mc start mc 0x80000000 0x80100000\0" \
+ "mcinitcmd=mmcinfo;mmc read 0x80a00000 0x5000 0x1000;" \
+ "mmc read 0x80e00000 0x7000 0x800;" \
+ "fsl_mc start mc 0x80a00000 0x80e00000\0" \
"mcmemsize=0x70000000 \0"
#else
#define CONFIG_EXTRA_ENV_SETTINGS \
#endif /* CONFIG_NXP_ESBC */
#ifdef CONFIG_TFABOOT
+#define BOOT_TARGET_DEVICES(func) \
+ func(USB, usb, 0) \
+ func(MMC, mmc, 0) \
+ func(SCSI, scsi, 0) \
+ func(DHCP, dhcp, na)
+#include <config_distro_bootcmd.h>
+
#define SD_BOOTCOMMAND \
"env exists mcinitcmd && env exists secureboot "\
- "&& mmcinfo && mmc read $load_addr 0x3c00 0x800 " \
+ "&& mmcinfo && mmc read $load_addr 0x3600 0x800 " \
"&& esbc_validate $load_addr; " \
"env exists mcinitcmd && run mcinitcmd " \
"&& mmc read 0x80d00000 0x6800 0x800 " \
"&& fsl_mc lazyapply dpl 0x80d00000; " \
- "run sd_bootcmd; " \
+ "run distro_bootcmd;run sd_bootcmd; " \
"env exists secureboot && esbc_halt;"
#define IFC_NOR_BOOTCOMMAND \
"env exists mcinitcmd && env exists secureboot "\
- "&& esbc_validate 0x580780000; env exists mcinitcmd "\
+ "&& esbc_validate 0x5806C0000; env exists mcinitcmd "\
"&& fsl_mc lazyapply dpl 0x580d00000;" \
- "run nor_bootcmd; " \
+ "run distro_bootcmd;run nor_bootcmd; " \
"env exists secureboot && esbc_halt;"
#endif
#if defined(CONFIG_FSL_MC_ENET) && !defined(CONFIG_SPL_BUILD)
#define CONFIG_FSL_MEMAC
-#define CONFIG_PHYLIB_10G
-#define CONFIG_PHY_VITESSE
-#define CONFIG_PHY_REALTEK
-#define CONFIG_PHY_TERANETICS
#define SGMII_CARD_PORT1_PHY_ADDR 0x1C
#define SGMII_CARD_PORT2_PHY_ADDR 0x1d
#define SGMII_CARD_PORT3_PHY_ADDR 0x1E
projects / platform / kernel / u-boot.git / blobdiff