#ifndef __LS2_COMMON_H
#define __LS2_COMMON_H
-#define CONFIG_REMAKE_ELF
-
#include <asm/arch/stream_id_lsch3.h>
#include <asm/arch/config.h>
/* Link Definitions */
-#ifdef CONFIG_TFABOOT
-#define CONFIG_SYS_INIT_SP_ADDR CONFIG_SYS_TEXT_BASE
-#else
-#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_FSL_OCRAM_BASE + 0xfff0)
-#endif
/* We need architecture specific misc initializations */
/* Link Definitions */
-#ifndef CONFIG_SYS_FSL_DDR4
-#define CONFIG_SYS_DDR_RAW_TIMING
-#endif
-
-#define CONFIG_SYS_FSL_DDR_INTLV_256B /* force 256 byte interleaving */
-
#define CONFIG_VERY_BIG_RAM
-#define CONFIG_SYS_DDR_SDRAM_BASE 0x80000000UL
-#define CONFIG_SYS_FSL_DDR_SDRAM_BASE_PHY 0
-#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE
-#define CONFIG_SYS_DDR_BLOCK2_BASE 0x8080000000ULL
-#define CONFIG_SYS_FSL_DDR_MAIN_NUM_CTRLS 2
+#define CFG_SYS_DDR_SDRAM_BASE 0x80000000UL
+#define CFG_SYS_FSL_DDR_SDRAM_BASE_PHY 0
+#define CFG_SYS_SDRAM_BASE CFG_SYS_DDR_SDRAM_BASE
+#define CFG_SYS_DDR_BLOCK2_BASE 0x8080000000ULL
/*
* SMP Definitinos
*/
#define CPU_RELEASE_ADDR secondary_boot_addr
-#define CONFIG_SYS_FSL_OTHER_DDR_NUM_CTRLS
-#ifdef CONFIG_SYS_FSL_HAS_DP_DDR
-#define CONFIG_SYS_DP_DDR_BASE 0x6000000000ULL
-/*
- * DDR controller use 0 as the base address for binding.
- * It is mapped to CONFIG_SYS_DP_DDR_BASE for core to access.
- */
-#define CONFIG_SYS_DP_DDR_BASE_PHY 0
-#define CONFIG_DP_DDR_CTRL 2
-#define CONFIG_DP_DDR_NUM_CTRLS 1
-#endif
-
-/* Generic Timer Definitions */
/*
* This is not an accurate number. It is used in start.S. The frequency
* will be udpated later when get_bus_freq(0) is available.
*/
-#define COUNTER_FREQUENCY 25000000 /* 25MHz */
/* GPIO */
/* I2C */
/* Serial Port */
-#define CONFIG_SYS_NS16550_SERIAL
-#define CONFIG_SYS_NS16550_REG_SIZE 1
-#define CONFIG_SYS_NS16550_CLK (get_serial_clock())
+#define CFG_SYS_NS16550_CLK (get_serial_clock())
/*
* During booting, IFC is mapped at the region of 0x30000000.
* 0x5_C000_0000..0x5_ffff_ffff IFC CS1 1GB (NOR/Promjet)
*
* For e.g. NOR flash at CS0 will be mapped to 0x580000000 after relocation.
- * CONFIG_SYS_FLASH_BASE has the final address (core view)
- * CONFIG_SYS_FLASH_BASE_PHYS has the final address (IFC view)
- * CONFIG_SYS_FLASH_BASE_PHYS_EARLY has the temporary IFC address
- * CONFIG_SYS_TEXT_BASE is linked to 0x30000000 for booting
+ * CFG_SYS_FLASH_BASE has the final address (core view)
+ * CFG_SYS_FLASH_BASE_PHYS has the final address (IFC view)
+ * CFG_SYS_FLASH_BASE_PHYS_EARLY has the temporary IFC address
+ * CONFIG_TEXT_BASE is linked to 0x30000000 for booting
*/
-#define CONFIG_SYS_FLASH_BASE 0x580000000ULL
-#define CONFIG_SYS_FLASH_BASE_PHYS 0x80000000
-#define CONFIG_SYS_FLASH_BASE_PHYS_EARLY 0x00000000
+#define CFG_SYS_FLASH_BASE 0x580000000ULL
+#define CFG_SYS_FLASH_BASE_PHYS 0x80000000
+#define CFG_SYS_FLASH_BASE_PHYS_EARLY 0x00000000
-#define CONFIG_SYS_FLASH1_BASE_PHYS 0xC0000000
-#define CONFIG_SYS_FLASH1_BASE_PHYS_EARLY 0x8000000
+#define CFG_SYS_FLASH1_BASE_PHYS 0xC0000000
+#define CFG_SYS_FLASH1_BASE_PHYS_EARLY 0x8000000
#ifndef __ASSEMBLY__
unsigned long long get_qixis_addr(void);
#define QIXIS_SDID_MASK 0x07
#define QIXIS_ESDHC_NO_ADAPTER 0x7
-#define CONFIG_SYS_NAND_BASE 0x530000000ULL
-#define CONFIG_SYS_NAND_BASE_PHYS 0x30000000
+#define CFG_SYS_NAND_BASE 0x530000000ULL
+#define CFG_SYS_NAND_BASE_PHYS 0x30000000
/* MC firmware */
/* TODO Actual DPL max length needs to be confirmed with the MC FW team */
-#define CONFIG_SYS_LS_MC_DPC_MAX_LENGTH 0x20000
-#define CONFIG_SYS_LS_MC_DRAM_DPC_OFFSET 0x00F00000
-#define CONFIG_SYS_LS_MC_DPL_MAX_LENGTH 0x20000
-#define CONFIG_SYS_LS_MC_DRAM_DPL_OFFSET 0x00F20000
+#define CFG_SYS_LS_MC_DPC_MAX_LENGTH 0x20000
+#define CFG_SYS_LS_MC_DRAM_DPC_OFFSET 0x00F00000
+#define CFG_SYS_LS_MC_DPL_MAX_LENGTH 0x20000
+#define CFG_SYS_LS_MC_DRAM_DPL_OFFSET 0x00F20000
/* For LS2085A */
-#define CONFIG_SYS_LS_MC_AIOP_IMG_MAX_LENGTH 0x200000
-#define CONFIG_SYS_LS_MC_DRAM_AIOP_IMG_OFFSET 0x07000000
-
-/* Define phy_reset function to boot the MC based on mcinitcmd.
- * This happens late enough to properly fixup u-boot env MAC addresses.
- */
-#define CONFIG_RESET_PHY_R
+#define CFG_SYS_LS_MC_AIOP_IMG_MAX_LENGTH 0x200000
+#define CFG_SYS_LS_MC_DRAM_AIOP_IMG_OFFSET 0x07000000
/*
* Carve out a DDR region which will not be used by u-boot/Linux
* 512MB aligned, so the min size to hide is 512MB.
*/
#ifdef CONFIG_FSL_MC_ENET
-#define CONFIG_SYS_LS_MC_DRAM_BLOCK_MIN_SIZE (128UL * 1024 * 1024)
+#define CFG_SYS_LS_MC_DRAM_BLOCK_MIN_SIZE (128UL * 1024 * 1024)
#endif
/* Miscellaneous configurable options */
/* Physical Memory Map */
/* fixme: these need to be checked against the board */
-#define CONFIG_CHIP_SELECTS_PER_CTRL 4
-#define CONFIG_HWCONFIG
#define HWCONFIG_BUFFER_SIZE 128
/* Initial environment variables */
"mcinitcmd=fsl_mc start mc 0x580a00000" \
" 0x580e00000 \0"
-/* Monitor Command Prompt */
-#define CONFIG_SYS_CBSIZE 512 /* Console I/O Buffer Size */
-#define CONFIG_SYS_MAXARGS 64 /* max command args */
-
-#define CONFIG_SPL_BSS_START_ADDR 0x80100000
-#define CONFIG_SPL_BSS_MAX_SIZE 0x00100000
-#define CONFIG_SPL_MAX_SIZE 0x16000
-#define CONFIG_SPL_STACK (CONFIG_SYS_FSL_OCRAM_BASE + 0x9ff0)
-#define CONFIG_SPL_TARGET "u-boot-with-spl.bin"
-
#ifdef CONFIG_NAND_BOOT
-#define CONFIG_SYS_NAND_U_BOOT_DST 0x80400000
-#define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_NAND_U_BOOT_DST
+#define CFG_SYS_NAND_U_BOOT_DST 0x80400000
+#define CFG_SYS_NAND_U_BOOT_START CFG_SYS_NAND_U_BOOT_DST
#endif
-#define CONFIG_SYS_SPL_MALLOC_SIZE 0x00100000
-#define CONFIG_SYS_SPL_MALLOC_START 0x80200000
-#define CONFIG_SYS_MONITOR_LEN (1024 * 1024)
-
-#define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */
#include <asm/arch/soc.h>