#ifndef __LS2_COMMON_H
#define __LS2_COMMON_H
-#define CONFIG_REMAKE_ELF
-#define CONFIG_GICV3
-
#include <asm/arch/stream_id_lsch3.h>
#include <asm/arch/config.h>
/* Link Definitions */
-#ifdef CONFIG_TFABOOT
-#define CONFIG_SYS_INIT_SP_ADDR CONFIG_SYS_TEXT_BASE
-#else
-#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_FSL_OCRAM_BASE + 0xfff0)
-#endif
/* We need architecture specific misc initializations */
/* Link Definitions */
-#define CONFIG_SKIP_LOWLEVEL_INIT
-
-#ifndef CONFIG_SYS_FSL_DDR4
-#define CONFIG_SYS_DDR_RAW_TIMING
-#endif
-
-#define CONFIG_SYS_FSL_DDR_INTLV_256B /* force 256 byte interleaving */
-
#define CONFIG_VERY_BIG_RAM
#define CONFIG_SYS_DDR_SDRAM_BASE 0x80000000UL
#define CONFIG_SYS_FSL_DDR_SDRAM_BASE_PHY 0
/*
* SMP Definitinos
*/
-#define CPU_RELEASE_ADDR secondary_boot_func
+#define CPU_RELEASE_ADDR secondary_boot_addr
#define CONFIG_SYS_FSL_OTHER_DDR_NUM_CTRLS
-#ifdef CONFIG_SYS_FSL_HAS_DP_DDR
-#define CONFIG_SYS_DP_DDR_BASE 0x6000000000ULL
-/*
- * DDR controller use 0 as the base address for binding.
- * It is mapped to CONFIG_SYS_DP_DDR_BASE for core to access.
- */
-#define CONFIG_SYS_DP_DDR_BASE_PHY 0
-#define CONFIG_DP_DDR_CTRL 2
-#define CONFIG_DP_DDR_NUM_CTRLS 1
-#endif
-/* Generic Timer Definitions */
/*
* This is not an accurate number. It is used in start.S. The frequency
* will be udpated later when get_bus_freq(0) is available.
*/
-#define COUNTER_FREQUENCY 25000000 /* 25MHz */
-/* Size of malloc() pool */
-#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 2048 * 1024)
+/* GPIO */
/* I2C */
-#ifndef CONFIG_DM_I2C
-#define CONFIG_SYS_I2C
-#endif
/* Serial Port */
#define CONFIG_SYS_NS16550_SERIAL
#define CONFIG_SYS_NS16550_REG_SIZE 1
#define CONFIG_SYS_NS16550_CLK (get_serial_clock())
-#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
-
-/* IFC */
-#define CONFIG_FSL_IFC
-
/*
* During booting, IFC is mapped at the region of 0x30000000.
* But this region is limited to 256MB. To accommodate NOR, promjet
#define CONFIG_SYS_LS_MC_AIOP_IMG_MAX_LENGTH 0x200000
#define CONFIG_SYS_LS_MC_DRAM_AIOP_IMG_OFFSET 0x07000000
-/* Define phy_reset function to boot the MC based on mcinitcmd.
- * This happens late enough to properly fixup u-boot env MAC addresses.
- */
-#define CONFIG_RESET_PHY_R
-
/*
* Carve out a DDR region which will not be used by u-boot/Linux
*
#endif
/* Miscellaneous configurable options */
-#define CONFIG_SYS_LOAD_ADDR (CONFIG_SYS_DDR_SDRAM_BASE + 0x10000000)
/* Physical Memory Map */
/* fixme: these need to be checked against the board */
-#define CONFIG_CHIP_SELECTS_PER_CTRL 4
#define CONFIG_HWCONFIG
#define HWCONFIG_BUFFER_SIZE 128
-/* Allow to overwrite serial and ethaddr */
-#define CONFIG_ENV_OVERWRITE
-
/* Initial environment variables */
#define CONFIG_EXTRA_ENV_SETTINGS \
"hwconfig=fsl_ddr:bank_intlv=auto\0" \
"mcinitcmd=fsl_mc start mc 0x580a00000" \
" 0x580e00000 \0"
-#ifndef CONFIG_TFABOOT
-#ifdef CONFIG_SD_BOOT
-#define CONFIG_BOOTCOMMAND "mmc read 0x80200000 0x6800 0x800;"\
- " fsl_mc apply dpl 0x80200000 &&" \
- " mmc read $kernel_load $kernel_start" \
- " $kernel_size && bootm $kernel_load"
-#else
-#define CONFIG_BOOTCOMMAND "fsl_mc apply dpl 0x580d00000 &&" \
- " cp.b $kernel_start $kernel_load" \
- " $kernel_size && bootm $kernel_load"
-#endif
-#endif
-
-/* Monitor Command Prompt */
-#define CONFIG_SYS_CBSIZE 512 /* Console I/O Buffer Size */
-#define CONFIG_SYS_MAXARGS 64 /* max command args */
-
-#define CONFIG_SPL_BSS_START_ADDR 0x80100000
-#define CONFIG_SPL_BSS_MAX_SIZE 0x00100000
-#define CONFIG_SPL_MAX_SIZE 0x16000
-#define CONFIG_SPL_STACK (CONFIG_SYS_FSL_OCRAM_BASE + 0x9ff0)
-#define CONFIG_SPL_TARGET "u-boot-with-spl.bin"
-
#ifdef CONFIG_NAND_BOOT
#define CONFIG_SYS_NAND_U_BOOT_DST 0x80400000
#define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_NAND_U_BOOT_DST
#endif
-#define CONFIG_SYS_SPL_MALLOC_SIZE 0x00100000
-#define CONFIG_SYS_SPL_MALLOC_START 0x80200000
#define CONFIG_SYS_MONITOR_LEN (1024 * 1024)
-#define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */
-
#include <asm/arch/soc.h>
#endif /* __LS2_COMMON_H */