#ifndef __LS2_COMMON_H
#define __LS2_COMMON_H
-
#define CONFIG_REMAKE_ELF
#define CONFIG_FSL_LAYERSCAPE
-#define CONFIG_FSL_LSCH3
#define CONFIG_MP
#define CONFIG_GICV3
#define CONFIG_FSL_TZPC_BP147
-/* Errata fixes */
-#define CONFIG_ARM_ERRATA_828024
-#define CONFIG_ARM_ERRATA_826974
-
#include <asm/arch/ls2080a_stream_id.h>
#include <asm/arch/config.h>
-#if (defined(CONFIG_SYS_FSL_SRDS_1) || defined(CONFIG_SYS_FSL_SRDS_2))
-#define CONFIG_SYS_HAS_SERDES
-#endif
/* Link Definitions */
#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_FSL_OCRAM_BASE + 0xfff0)
/* We need architecture specific misc initializations */
#define CONFIG_ARCH_MISC_INIT
+#define CONFIG_FSL_CAAM /* Enable SEC/CAAM */
+
/* Link Definitions */
+#ifndef CONFIG_QSPI_BOOT
#ifdef CONFIG_SPL
#define CONFIG_SYS_TEXT_BASE 0x80400000
#else
#define CONFIG_SYS_TEXT_BASE 0x30100000
#endif
+#endif
#ifdef CONFIG_EMU
#define CONFIG_SYS_NO_FLASH
#define CONFIG_SUPPORT_RAW_INITRD
#define CONFIG_SKIP_LOWLEVEL_INIT
-#define CONFIG_BOARD_EARLY_INIT_F 1
-
-/* Flat Device Tree Definitions */
-#define CONFIG_OF_LIBFDT
-#define CONFIG_OF_BOARD_SETUP
-#define CONFIG_OF_STDOUT_VIA_ALIAS
-
-/* new uImage format support */
-#define CONFIG_FIT
-#define CONFIG_FIT_VERBOSE /* enable fit_format_{error,warning}() */
#ifndef CONFIG_SPL
#define CONFIG_FSL_DDR_INTERACTIVE /* Interactive debugging */
#endif
#ifndef CONFIG_SYS_FSL_DDR4
-#define CONFIG_SYS_FSL_DDR3 /* Use DDR3 memory */
#define CONFIG_SYS_DDR_RAW_TIMING
#endif
#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 2048 * 1024)
/* I2C */
-#define CONFIG_CMD_I2C
#define CONFIG_SYS_I2C
#define CONFIG_SYS_I2C_MXC
#define CONFIG_SYS_I2C_MXC_I2C1 /* enable I2C bus 1 */
#define CONFIG_CONS_INDEX 1
#define CONFIG_SYS_NS16550_SERIAL
#define CONFIG_SYS_NS16550_REG_SIZE 1
-#define CONFIG_SYS_NS16550_CLK (get_bus_freq(0)/2)
+#define CONFIG_SYS_NS16550_CLK (get_serial_clock())
#define CONFIG_BAUDRATE 115200
#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
#define CONFIG_SYS_FLASH1_BASE_PHYS 0xC0000000
#define CONFIG_SYS_FLASH1_BASE_PHYS_EARLY 0x8000000
-#ifndef CONFIG_SYS_NO_FLASH
-#define CONFIG_FLASH_CFI_DRIVER
-#define CONFIG_SYS_FLASH_CFI
-#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
-#define CONFIG_SYS_FLASH_QUIET_TEST
-#endif
-
#ifndef __ASSEMBLY__
unsigned long long get_qixis_addr(void);
#endif
#define CONFIG_SYS_NAND_BASE 0x530000000ULL
#define CONFIG_SYS_NAND_BASE_PHYS 0x30000000
-/* Debug Server firmware */
-#define CONFIG_FSL_DEBUG_SERVER
-/* 2 sec timeout */
-#define CONFIG_SYS_DEBUG_SERVER_TIMEOUT (2 * 1000 * 1000)
-
/* MC firmware */
#define CONFIG_FSL_MC_ENET
/* TODO Actual DPL max length needs to be confirmed with the MC FW team */
#define CONFIG_SYS_LS_MC_DRAM_DPC_OFFSET 0x00F00000
#define CONFIG_SYS_LS_MC_DPL_MAX_LENGTH 0x20000
#define CONFIG_SYS_LS_MC_DRAM_DPL_OFFSET 0x00F20000
-#ifdef CONFIG_LS2085A
+/* For LS2085A */
#define CONFIG_SYS_LS_MC_AIOP_IMG_MAX_LENGTH 0x200000
#define CONFIG_SYS_LS_MC_DRAM_AIOP_IMG_OFFSET 0x07000000
-#endif
/*
* Carve out a DDR region which will not be used by u-boot/Linux
* It will be used by MC and Debug Server. The MC region must be
* 512MB aligned, so the min size to hide is 512MB.
*/
-#if defined(CONFIG_FSL_MC_ENET) || defined(CONFIG_FSL_DEBUG_SERVER)
-#define CONFIG_SYS_DEBUG_SERVER_DRAM_BLOCK_MIN_SIZE (256UL * 1024 * 1024)
-#define CONFIG_SYS_LS_MC_DRAM_BLOCK_MIN_SIZE (256UL * 1024 * 1024)
-#define CONFIG_SYS_MEM_TOP_HIDE_MIN (512UL * 1024 * 1024)
-#define CONFIG_SYS_MEM_TOP_HIDE get_dram_size_to_hide()
-#endif
-
-/* PCIe */
-#define CONFIG_PCIE1 /* PCIE controler 1 */
-#define CONFIG_PCIE2 /* PCIE controler 2 */
-#define CONFIG_PCIE3 /* PCIE controler 3 */
-#define CONFIG_PCIE4 /* PCIE controler 4 */
-#define CONFIG_PCIE_LAYERSCAPE /* Use common FSL Layerscape PCIe code */
-#ifdef CONFIG_LS2080A
-#define FSL_PCIE_COMPAT "fsl,ls2080a-pcie"
-#endif
-
-#ifdef CONFIG_LS2085A
-#define FSL_PCIE_COMPAT "fsl,ls2085a-pcie"
+#ifdef CONFIG_FSL_MC_ENET
+#define CONFIG_SYS_LS_MC_DRAM_BLOCK_MIN_SIZE (512UL * 1024 * 1024)
+#define CONFIG_SYS_MC_RSV_MEM_ALIGN (512UL * 1024 * 1024)
#endif
-#define CONFIG_SYS_PCI_64BIT
-
-#define CONFIG_SYS_PCIE_CFG0_PHYS_OFF 0x00000000
-#define CONFIG_SYS_PCIE_CFG0_SIZE 0x00001000 /* 4k */
-#define CONFIG_SYS_PCIE_CFG1_PHYS_OFF 0x00001000
-#define CONFIG_SYS_PCIE_CFG1_SIZE 0x00001000 /* 4k */
-
-#define CONFIG_SYS_PCIE_IO_BUS 0x00000000
-#define CONFIG_SYS_PCIE_IO_PHYS_OFF 0x00010000
-#define CONFIG_SYS_PCIE_IO_SIZE 0x00010000 /* 64k */
-
-#define CONFIG_SYS_PCIE_MEM_BUS 0x40000000
-#define CONFIG_SYS_PCIE_MEM_PHYS_OFF 0x40000000
-#define CONFIG_SYS_PCIE_MEM_SIZE 0x40000000 /* 1G */
-
/* Command line configuration */
-#define CONFIG_CMD_CACHE
-#define CONFIG_CMD_DHCP
#define CONFIG_CMD_ENV
-#define CONFIG_CMD_GREPENV
-#define CONFIG_CMD_MII
-#define CONFIG_CMD_PING
/* Miscellaneous configurable options */
#define CONFIG_SYS_LOAD_ADDR (CONFIG_SYS_DDR_SDRAM_BASE + 0x10000000)
-#define CONFIG_ARCH_EARLY_INIT_R
/* Physical Memory Map */
/* fixme: these need to be checked against the board */
#define CONFIG_HWCONFIG
#define HWCONFIG_BUFFER_SIZE 128
-#define CONFIG_DISPLAY_CPUINFO
-
/* Allow to overwrite serial and ethaddr */
#define CONFIG_ENV_OVERWRITE
"kernel_start=0x581200000\0" \
"kernel_load=0xa0000000\0" \
"kernel_size=0x2800000\0" \
- "console=ttyAMA0,38400n8\0"
+ "console=ttyAMA0,38400n8\0" \
+ "mcinitcmd=fsl_mc start mc 0x580300000" \
+ " 0x580800000 \0"
#define CONFIG_BOOTARGS "console=ttyS0,115200 root=/dev/ram0 " \
- "earlycon=uart8250,mmio,0x21c0500" \
+ "earlycon=uart8250,mmio,0x21c0500 " \
"ramdisk_size=0x2000000 default_hugepagesz=2m" \
- " hugepagesz=2m hugepages=16"
-#define CONFIG_BOOTCOMMAND "cp.b $kernel_start $kernel_load " \
- "$kernel_size && bootm $kernel_load"
-#define CONFIG_BOOTDELAY 10
+ " hugepagesz=2m hugepages=256"
+#define CONFIG_BOOTCOMMAND "fsl_mc apply dpl 0x580700000 &&" \
+ " cp.b $kernel_start $kernel_load" \
+ " $kernel_size && bootm $kernel_load"
/* Monitor Command Prompt */
#define CONFIG_SYS_CBSIZE 512 /* Console I/O Buffer Size */
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \
sizeof(CONFIG_SYS_PROMPT) + 16)
-#define CONFIG_SYS_HUSH_PARSER
-#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot args buffer */
#define CONFIG_SYS_LONGHELP
#define CONFIG_CMDLINE_EDITING 1
#define CONFIG_AUTO_COMPLETE
#define CONFIG_SYS_MAXARGS 64 /* max command args */
-#ifndef __ASSEMBLY__
-unsigned long get_dram_size_to_hide(void);
-#endif
-
#define CONFIG_PANIC_HANG /* do not reset board on panic */
#define CONFIG_SPL_BSS_START_ADDR 0x80100000
#define CONFIG_SPL_BSS_MAX_SIZE 0x00100000
-#define CONFIG_SPL_DRIVERS_MISC_SUPPORT
-#define CONFIG_SPL_ENV_SUPPORT
#define CONFIG_SPL_FRAMEWORK
-#define CONFIG_SPL_I2C_SUPPORT
#define CONFIG_SPL_LDSCRIPT "arch/arm/cpu/armv8/u-boot-spl.lds"
-#define CONFIG_SPL_LIBCOMMON_SUPPORT
-#define CONFIG_SPL_LIBGENERIC_SUPPORT
#define CONFIG_SPL_MAX_SIZE 0x16000
-#define CONFIG_SPL_MPC8XXX_INIT_DDR_SUPPORT
-#define CONFIG_SPL_NAND_SUPPORT
-#define CONFIG_SPL_SERIAL_SUPPORT
#define CONFIG_SPL_STACK (CONFIG_SYS_FSL_OCRAM_BASE + 0x9ff0)
#define CONFIG_SPL_TARGET "u-boot-with-spl.bin"
#define CONFIG_SPL_TEXT_BASE 0x1800a000
#define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_NAND_U_BOOT_DST
#define CONFIG_SYS_SPL_MALLOC_SIZE 0x00100000
#define CONFIG_SYS_SPL_MALLOC_START 0x80200000
-#define CONFIG_SYS_MONITOR_LEN (512 * 1024)
+#define CONFIG_SYS_MONITOR_LEN (640 * 1024)
#define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */
+/* Hash command with SHA acceleration supported in hardware */
+#ifdef CONFIG_FSL_CAAM
+#define CONFIG_CMD_HASH
+#define CONFIG_SHA_HW_ACCEL
+#endif
#endif /* __LS2_COMMON_H */
projects / platform / kernel / u-boot.git / blobdiff