+/* SPDX-License-Identifier: GPL-2.0+ */
/*
+ * Copyright 2017 NXP
* Copyright (C) 2014 Freescale Semiconductor
- *
- * SPDX-License-Identifier: GPL-2.0+
*/
#ifndef __LS2_COMMON_H
#define __LS2_COMMON_H
#define CONFIG_REMAKE_ELF
-#define CONFIG_FSL_LAYERSCAPE
-#define CONFIG_MP
-#define CONFIG_GICV3
-#define CONFIG_FSL_TZPC_BP147
#include <asm/arch/stream_id_lsch3.h>
#include <asm/arch/config.h>
/* Link Definitions */
+#ifdef CONFIG_TFABOOT
+#define CONFIG_SYS_INIT_SP_ADDR CONFIG_SYS_TEXT_BASE
+#else
#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_FSL_OCRAM_BASE + 0xfff0)
+#endif
/* We need architecture specific misc initializations */
/* Link Definitions */
-#ifndef CONFIG_QSPI_BOOT
-#ifdef CONFIG_SPL
-#define CONFIG_SYS_TEXT_BASE 0x80400000
-#else
-#define CONFIG_SYS_TEXT_BASE 0x30100000
-#endif
-#endif
-#define CONFIG_SUPPORT_RAW_INITRD
-
-#define CONFIG_SKIP_LOWLEVEL_INIT
-
-#ifndef CONFIG_SPL
-#define CONFIG_FSL_DDR_INTERACTIVE /* Interactive debugging */
-#endif
#ifndef CONFIG_SYS_FSL_DDR4
#define CONFIG_SYS_DDR_RAW_TIMING
#endif
/*
* SMP Definitinos
*/
-#define CPU_RELEASE_ADDR secondary_boot_func
+#define CPU_RELEASE_ADDR secondary_boot_addr
#define CONFIG_SYS_FSL_OTHER_DDR_NUM_CTRLS
#ifdef CONFIG_SYS_FSL_HAS_DP_DDR
*/
#define COUNTER_FREQUENCY 25000000 /* 25MHz */
-/* Size of malloc() pool */
-#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 2048 * 1024)
+/* GPIO */
+#ifdef CONFIG_DM_GPIO
+#ifndef CONFIG_MPC8XXX_GPIO
+#define CONFIG_MPC8XXX_GPIO
+#endif
+#endif
/* I2C */
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_I2C_MXC
-#define CONFIG_SYS_I2C_MXC_I2C1 /* enable I2C bus 1 */
-#define CONFIG_SYS_I2C_MXC_I2C2 /* enable I2C bus 2 */
-#define CONFIG_SYS_I2C_MXC_I2C3 /* enable I2C bus 3 */
-#define CONFIG_SYS_I2C_MXC_I2C4 /* enable I2C bus 4 */
/* Serial Port */
-#define CONFIG_CONS_INDEX 1
#define CONFIG_SYS_NS16550_SERIAL
#define CONFIG_SYS_NS16550_REG_SIZE 1
#define CONFIG_SYS_NS16550_CLK (get_serial_clock())
#define CONFIG_SYS_LS_MC_AIOP_IMG_MAX_LENGTH 0x200000
#define CONFIG_SYS_LS_MC_DRAM_AIOP_IMG_OFFSET 0x07000000
+/* Define phy_reset function to boot the MC based on mcinitcmd.
+ * This happens late enough to properly fixup u-boot env MAC addresses.
+ */
+#define CONFIG_RESET_PHY_R
+
/*
* Carve out a DDR region which will not be used by u-boot/Linux
*
* 512MB aligned, so the min size to hide is 512MB.
*/
#ifdef CONFIG_FSL_MC_ENET
-#define CONFIG_SYS_LS_MC_DRAM_BLOCK_MIN_SIZE (512UL * 1024 * 1024)
+#define CONFIG_SYS_LS_MC_DRAM_BLOCK_MIN_SIZE (128UL * 1024 * 1024)
#endif
-/* Command line configuration */
-#define CONFIG_CMD_ENV
-
/* Miscellaneous configurable options */
-#define CONFIG_SYS_LOAD_ADDR (CONFIG_SYS_DDR_SDRAM_BASE + 0x10000000)
/* Physical Memory Map */
/* fixme: these need to be checked against the board */
#define CONFIG_CHIP_SELECTS_PER_CTRL 4
-#define CONFIG_NR_DRAM_BANKS 3
-
#define CONFIG_HWCONFIG
#define HWCONFIG_BUFFER_SIZE 128
-/* Allow to overwrite serial and ethaddr */
-#define CONFIG_ENV_OVERWRITE
-
/* Initial environment variables */
#define CONFIG_EXTRA_ENV_SETTINGS \
"hwconfig=fsl_ddr:bank_intlv=auto\0" \
"ramdisk_size=0x2000000\0" \
"fdt_high=0xa0000000\0" \
"initrd_high=0xffffffffffffffff\0" \
- "kernel_start=0x581200000\0" \
+ "kernel_start=0x581000000\0" \
"kernel_load=0xa0000000\0" \
"kernel_size=0x2800000\0" \
"console=ttyAMA0,38400n8\0" \
- "mcinitcmd=fsl_mc start mc 0x580300000" \
- " 0x580800000 \0"
-
-#define CONFIG_BOOTARGS "console=ttyS0,115200 root=/dev/ram0 " \
- "earlycon=uart8250,mmio,0x21c0500 " \
- "ramdisk_size=0x2000000 default_hugepagesz=2m" \
- " hugepagesz=2m hugepages=256"
-#define CONFIG_BOOTCOMMAND "fsl_mc apply dpl 0x580700000 &&" \
+ "mcinitcmd=fsl_mc start mc 0x580a00000" \
+ " 0x580e00000 \0"
+
+#ifndef CONFIG_TFABOOT
+#ifdef CONFIG_SD_BOOT
+#define CONFIG_BOOTCOMMAND "mmc read 0x80200000 0x6800 0x800;"\
+ " fsl_mc apply dpl 0x80200000 &&" \
+ " mmc read $kernel_load $kernel_start" \
+ " $kernel_size && bootm $kernel_load"
+#else
+#define CONFIG_BOOTCOMMAND "fsl_mc apply dpl 0x580d00000 &&" \
" cp.b $kernel_start $kernel_load" \
" $kernel_size && bootm $kernel_load"
+#endif
+#endif
/* Monitor Command Prompt */
#define CONFIG_SYS_CBSIZE 512 /* Console I/O Buffer Size */
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \
- sizeof(CONFIG_SYS_PROMPT) + 16)
-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot args buffer */
-#define CONFIG_SYS_LONGHELP
-#define CONFIG_CMDLINE_EDITING 1
-#define CONFIG_AUTO_COMPLETE
#define CONFIG_SYS_MAXARGS 64 /* max command args */
-#define CONFIG_PANIC_HANG /* do not reset board on panic */
-
#define CONFIG_SPL_BSS_START_ADDR 0x80100000
#define CONFIG_SPL_BSS_MAX_SIZE 0x00100000
-#define CONFIG_SPL_FRAMEWORK
-#define CONFIG_SPL_LDSCRIPT "arch/arm/cpu/armv8/u-boot-spl.lds"
#define CONFIG_SPL_MAX_SIZE 0x16000
#define CONFIG_SPL_STACK (CONFIG_SYS_FSL_OCRAM_BASE + 0x9ff0)
#define CONFIG_SPL_TARGET "u-boot-with-spl.bin"
-#define CONFIG_SPL_TEXT_BASE 0x1800a000
+#ifdef CONFIG_NAND_BOOT
#define CONFIG_SYS_NAND_U_BOOT_DST 0x80400000
#define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_NAND_U_BOOT_DST
+#endif
#define CONFIG_SYS_SPL_MALLOC_SIZE 0x00100000
#define CONFIG_SYS_SPL_MALLOC_START 0x80200000
-#define CONFIG_SYS_MONITOR_LEN (640 * 1024)
+#define CONFIG_SYS_MONITOR_LEN (1024 * 1024)
#define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */
-/* Hash command with SHA acceleration supported in hardware */
-#ifdef CONFIG_FSL_CAAM
-#define CONFIG_CMD_HASH
-#define CONFIG_SHA_HW_ACCEL
-#endif
+#include <asm/arch/soc.h>
#endif /* __LS2_COMMON_H */