/* SPDX-License-Identifier: GPL-2.0+ */
/*
- * Copyright 2017 NXP
+ * Copyright 2017, 2020-2021 NXP
*/
#ifndef __LS1088A_RDB_H
#include "ls1088a_common.h"
-#define CONFIG_MISC_INIT_R
-
-#if defined(CONFIG_QSPI_BOOT)
-#define CONFIG_ENV_SIZE 0x2000 /* 8KB */
-#define CONFIG_ENV_SECT_SIZE 0x40000
-#elif defined(CONFIG_SD_BOOT)
-#define CONFIG_ENV_OFFSET (3 * 1024 * 1024)
-#define CONFIG_SYS_MMC_ENV_DEV 0
-#define CONFIG_ENV_SIZE 0x2000
-#else
-#define CONFIG_ENV_IS_IN_FLASH
-#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x300000)
-#define CONFIG_ENV_SECT_SIZE 0x20000
-#define CONFIG_ENV_SIZE 0x20000
-#endif
-
-#if defined(CONFIG_QSPI_BOOT) || defined(CONFIG_SD_BOOT_QSPI)
+#if defined(CONFIG_TFABOOT) || \
+ defined(CONFIG_QSPI_BOOT) || defined(CONFIG_SD_BOOT_QSPI)
#ifndef CONFIG_SPL_BUILD
#define CONFIG_QIXIS_I2C_ACCESS
#endif
#define SYS_NO_FLASH
-#undef CONFIG_CMD_IMLS
#endif
#define CONFIG_SYS_CLK_FREQ 100000000
#define CONFIG_SYS_IFC_CCR 0x01000000
#ifndef SYS_NO_FLASH
-#define CONFIG_FLASH_CFI_DRIVER
-#define CONFIG_SYS_FLASH_CFI
-#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
#define CONFIG_SYS_FLASH_QUIET_TEST
#define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */
#define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND_BASE }
#define CONFIG_SYS_MAX_NAND_DEVICE 1
#define CONFIG_MTD_NAND_VERIFY_WRITE
-#define CONFIG_CMD_NAND
#define CONFIG_SYS_NAND_BLOCK_SIZE (128 * 1024)
FTIM2_GPCM_TWP(0x3E))
#define SYS_FPGA_CS_FTIM3 0x0
-#if defined(CONFIG_QSPI_BOOT) || defined(CONFIG_SD_BOOT_QSPI)
+#if defined(CONFIG_TFABOOT) || \
+ defined(CONFIG_QSPI_BOOT) || defined(CONFIG_SD_BOOT_QSPI)
#define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_NAND_CSPR_EXT
#define CONFIG_SYS_CSPR0 CONFIG_SYS_NAND_CSPR
#define CONFIG_SYS_AMASK0 CONFIG_SYS_NAND_AMASK
#define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NOR_FTIM3
#endif
-
#define CONFIG_SYS_LS_MC_BOOT_TIMEOUT_MS 5000
-#define I2C_MUX_CH_VOL_MONITOR 0xA
+#define I2C_MUX_CH_VOL_MONITOR 0xA
/* Voltage monitor on channel 2*/
#define I2C_VOL_MONITOR_ADDR 0x63
#define I2C_VOL_MONITOR_BUS_V_OFFSET 0x2
#define CONFIG_VOL_MONITOR_LTC3882_SET
#define CONFIG_VOL_MONITOR_LTC3882_READ
-/* PM Bus commands code for LTC3882*/
-#define PMBUS_CMD_PAGE 0x0
-#define PMBUS_CMD_READ_VOUT 0x8B
-#define PMBUS_CMD_PAGE_PLUS_WRITE 0x05
-#define PMBUS_CMD_VOUT_COMMAND 0x21
-
#define PWM_CHANNEL0 0x0
/*
* RTC configuration
*/
#define RTC
-#define CONFIG_RTC_PCF8563 1
#define CONFIG_SYS_I2C_RTC_ADDR 0x51 /* Channel 3*/
-#define CONFIG_CMD_DATE
#endif
/* EEPROM */
-#define CONFIG_ID_EEPROM
#define CONFIG_SYS_I2C_EEPROM_NXID
#define CONFIG_SYS_EEPROM_BUS_NUM 0
#define CONFIG_SYS_I2C_EEPROM_ADDR 0x57
#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3
#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5
-#ifndef SPL_NO_QSPI
-/* QSPI device */
-#if defined(CONFIG_QSPI_BOOT) || defined(CONFIG_SD_BOOT_QSPI)
-#define CONFIG_FSL_QSPI
-#define FSL_QSPI_FLASH_SIZE (1 << 26)
-#define FSL_QSPI_FLASH_NUM 2
-#endif
-#endif
-
-#define CONFIG_CMD_MEMINFO
-#define CONFIG_SYS_MEMTEST_START 0x80000000
-#define CONFIG_SYS_MEMTEST_END 0x9fffffff
-
#ifdef CONFIG_SPL_BUILD
#define CONFIG_SYS_MONITOR_BASE CONFIG_SPL_TEXT_BASE
#else
#ifndef SPL_NO_ENV
/* Initial environment variables */
+#ifdef CONFIG_TFABOOT
+#define QSPI_MC_INIT_CMD \
+ "sf probe 0:0;sf read 0x80a00000 0xA00000 0x200000;" \
+ "sf read 0x80e00000 0xE00000 0x100000;" \
+ "env exists secureboot && " \
+ "sf read 0x80640000 0x640000 0x40000 && " \
+ "sf read 0x80680000 0x680000 0x40000 && " \
+ "esbc_validate 0x80640000 && " \
+ "esbc_validate 0x80680000 ;" \
+ "fsl_mc start mc 0x80a00000 0x80e00000\0"
+#define SD_MC_INIT_CMD \
+ "mmcinfo;mmc read 0x80a00000 0x5000 0x1000;" \
+ "mmc read 0x80e00000 0x7000 0x800;" \
+ "env exists secureboot && " \
+ "mmc read 0x80640000 0x3200 0x20 && " \
+ "mmc read 0x80680000 0x3400 0x20 && " \
+ "esbc_validate 0x80640000 && " \
+ "esbc_validate 0x80680000 ;" \
+ "fsl_mc start mc 0x80a00000 0x80e00000\0"
+#else
#if defined(CONFIG_QSPI_BOOT)
#define MC_INIT_CMD \
- "mcinitcmd=sf probe 0:0;sf read 0x80000000 0xA00000 0x100000;" \
- "sf read 0x80100000 0xE00000 0x100000;" \
+ "mcinitcmd=sf probe 0:0;sf read 0x80a00000 0xA00000 0x200000;" \
+ "sf read 0x80e00000 0xE00000 0x100000;" \
"env exists secureboot && " \
- "sf read 0x80700000 0x700000 0x40000 && " \
- "sf read 0x80740000 0x740000 0x40000 && " \
- "esbc_validate 0x80700000 && " \
- "esbc_validate 0x80740000 ;" \
- "fsl_mc start mc 0x80000000 0x80100000\0" \
+ "sf read 0x80640000 0x640000 0x40000 && " \
+ "sf read 0x80680000 0x680000 0x40000 && " \
+ "esbc_validate 0x80640000 && " \
+ "esbc_validate 0x80680000 ;" \
+ "fsl_mc start mc 0x80a00000 0x80e00000\0" \
"mcmemsize=0x70000000\0"
#elif defined(CONFIG_SD_BOOT)
#define MC_INIT_CMD \
- "mcinitcmd=mmcinfo;mmc read 0x80000000 0x5000 0x800;" \
- "mmc read 0x80100000 0x7000 0x800;" \
+ "mcinitcmd=mmcinfo;mmc read 0x80a00000 0x5000 0x1000;" \
+ "mmc read 0x80e00000 0x7000 0x800;" \
"env exists secureboot && " \
- "mmc read 0x80700000 0x3800 0x10 && " \
- "mmc read 0x80740000 0x3A00 0x10 && " \
- "esbc_validate 0x80700000 && " \
- "esbc_validate 0x80740000 ;" \
- "fsl_mc start mc 0x80000000 0x80100000\0" \
+ "mmc read 0x80640000 0x3200 0x20 && " \
+ "mmc read 0x80680000 0x3400 0x20 && " \
+ "esbc_validate 0x80640000 && " \
+ "esbc_validate 0x80680000 ;" \
+ "fsl_mc start mc 0x80a00000 0x80e00000\0" \
"mcmemsize=0x70000000\0"
#endif
+#endif /* CONFIG_TFABOOT */
#undef CONFIG_EXTRA_ENV_SETTINGS
+#ifdef CONFIG_TFABOOT
#define CONFIG_EXTRA_ENV_SETTINGS \
"BOARD=ls1088ardb\0" \
"hwconfig=fsl_ddr:bank_intlv=auto\0" \
"fdt_addr=0x64f00000\0" \
"kernel_addr=0x1000000\0" \
"kernel_addr_sd=0x8000\0" \
- "kernelhdr_addr_sd=0x4000\0" \
+ "kernelhdr_addr_sd=0x3000\0" \
+ "kernel_start=0x580100000\0" \
+ "kernelheader_start=0x580600000\0" \
+ "scriptaddr=0x80000000\0" \
+ "scripthdraddr=0x80080000\0" \
+ "fdtheader_addr_r=0x80100000\0" \
+ "kernelheader_addr=0x600000\0" \
+ "kernelheader_addr_r=0x80200000\0" \
+ "kernel_addr_r=0x81000000\0" \
+ "kernelheader_size=0x40000\0" \
+ "fdt_addr_r=0x90000000\0" \
+ "load_addr=0xa0000000\0" \
+ "kernel_size=0x2800000\0" \
+ "kernel_size_sd=0x14000\0" \
+ "kernelhdr_size_sd=0x20\0" \
+ QSPI_MC_INIT_CMD \
+ "mcmemsize=0x70000000\0" \
+ BOOTENV \
+ "boot_scripts=ls1088ardb_boot.scr\0" \
+ "boot_script_hdr=hdr_ls1088ardb_bs.out\0" \
+ "scan_dev_for_boot_part=" \
+ "part list ${devtype} ${devnum} devplist; " \
+ "env exists devplist || setenv devplist 1; " \
+ "for distro_bootpart in ${devplist}; do " \
+ "if fstype ${devtype} " \
+ "${devnum}:${distro_bootpart} " \
+ "bootfstype; then " \
+ "run scan_dev_for_boot; " \
+ "fi; " \
+ "done\0" \
+ "boot_a_script=" \
+ "load ${devtype} ${devnum}:${distro_bootpart} " \
+ "${scriptaddr} ${prefix}${script}; " \
+ "env exists secureboot && load ${devtype} " \
+ "${devnum}:${distro_bootpart} " \
+ "${scripthdraddr} ${prefix}${boot_script_hdr}; "\
+ "env exists secureboot " \
+ "&& esbc_validate ${scripthdraddr};" \
+ "source ${scriptaddr}\0" \
+ "installer=load mmc 0:2 $load_addr " \
+ "/flex_installer_arm64.itb; " \
+ "env exists mcinitcmd && run mcinitcmd && " \
+ "mmc read 0x80001000 0x6800 0x800;" \
+ "fsl_mc lazyapply dpl 0x80001000;" \
+ "bootm $load_addr#ls1088ardb\0" \
+ "qspi_bootcmd=echo Trying load from qspi..;" \
+ "sf probe && sf read $load_addr " \
+ "$kernel_addr $kernel_size ; env exists secureboot " \
+ "&& sf read $kernelheader_addr_r $kernelheader_addr " \
+ "$kernelheader_size && esbc_validate ${kernelheader_addr_r}; "\
+ "bootm $load_addr#$BOARD\0" \
+ "sd_bootcmd=echo Trying load from sd card..;" \
+ "mmcinfo; mmc read $load_addr " \
+ "$kernel_addr_sd $kernel_size_sd ;" \
+ "env exists secureboot && mmc read $kernelheader_addr_r "\
+ "$kernelhdr_addr_sd $kernelhdr_size_sd " \
+ " && esbc_validate ${kernelheader_addr_r};" \
+ "bootm $load_addr#$BOARD\0"
+#else
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "BOARD=ls1088ardb\0" \
+ "hwconfig=fsl_ddr:bank_intlv=auto\0" \
+ "ramdisk_addr=0x800000\0" \
+ "ramdisk_size=0x2000000\0" \
+ "fdt_high=0xa0000000\0" \
+ "initrd_high=0xffffffffffffffff\0" \
+ "fdt_addr=0x64f00000\0" \
+ "kernel_addr=0x1000000\0" \
+ "kernel_addr_sd=0x8000\0" \
+ "kernelhdr_addr_sd=0x3000\0" \
"kernel_start=0x580100000\0" \
"kernelheader_start=0x580800000\0" \
"scriptaddr=0x80000000\0" \
"scripthdraddr=0x80080000\0" \
"fdtheader_addr_r=0x80100000\0" \
- "kernelheader_addr=0x800000\0" \
+ "kernelheader_addr=0x600000\0" \
"kernelheader_addr_r=0x80200000\0" \
"kernel_addr_r=0x81000000\0" \
"kernelheader_size=0x40000\0" \
"load_addr=0xa0000000\0" \
"kernel_size=0x2800000\0" \
"kernel_size_sd=0x14000\0" \
- "kernelhdr_size_sd=0x10\0" \
+ "kernelhdr_size_sd=0x20\0" \
MC_INIT_CMD \
BOOTENV \
"boot_scripts=ls1088ardb_boot.scr\0" \
"run scan_dev_for_boot; " \
"fi; " \
"done\0" \
- "scan_dev_for_boot=" \
- "echo Scanning ${devtype} " \
- "${devnum}:${distro_bootpart}...; " \
- "for prefix in ${boot_prefixes}; do " \
- "run scan_dev_for_scripts; " \
- "done;\0" \
"boot_a_script=" \
"load ${devtype} ${devnum}:${distro_bootpart} " \
"${scriptaddr} ${prefix}${script}; " \
"$kernelhdr_addr_sd $kernelhdr_size_sd " \
" && esbc_validate ${kernelheader_addr_r};" \
"bootm $load_addr#$BOARD\0"
+#endif /* CONFIG_TFABOOT */
#undef CONFIG_BOOTCOMMAND
+#ifdef CONFIG_TFABOOT
+#define QSPI_NOR_BOOTCOMMAND \
+ "sf read 0x80001000 0xd00000 0x100000;" \
+ "env exists mcinitcmd && env exists secureboot " \
+ " && sf read 0x806C0000 0x6C0000 0x100000 " \
+ "&& esbc_validate 0x806C0000;env exists mcinitcmd " \
+ "&& fsl_mc lazyapply dpl 0x80001000;" \
+ "run distro_bootcmd;run qspi_bootcmd;" \
+ "env exists secureboot && esbc_halt;"
+#define SD_BOOTCOMMAND \
+ "env exists mcinitcmd && mmcinfo; " \
+ "mmc read 0x80001000 0x6800 0x800; " \
+ "env exists mcinitcmd && env exists secureboot " \
+ " && mmc read 0x806C0000 0x3600 0x20 " \
+ "&& esbc_validate 0x806C0000;env exists mcinitcmd " \
+ "&& fsl_mc lazyapply dpl 0x80001000;" \
+ "run distro_bootcmd;run sd_bootcmd;" \
+ "env exists secureboot && esbc_halt;"
+#else
#if defined(CONFIG_QSPI_BOOT)
/* Try to boot an on-QSPI kernel first, then do normal distro boot */
#define CONFIG_BOOTCOMMAND \
"sf read 0x80001000 0xd00000 0x100000;" \
"env exists mcinitcmd && env exists secureboot " \
- " && sf read 0x80780000 0x780000 0x100000 " \
- "&& esbc_validate 0x80780000;env exists mcinitcmd " \
+ " && sf read 0x806C0000 0x6C0000 0x100000 " \
+ "&& esbc_validate 0x806C0000;env exists mcinitcmd " \
"&& fsl_mc lazyapply dpl 0x80001000;" \
"run distro_bootcmd;run qspi_bootcmd;" \
"env exists secureboot && esbc_halt;"
"env exists mcinitcmd && mmcinfo; " \
"mmc read 0x80001000 0x6800 0x800; " \
"env exists mcinitcmd && env exists secureboot " \
- " && mmc read 0x80780000 0x3C00 0x10 " \
- "&& esbc_validate 0x80780000;env exists mcinitcmd " \
+ " && mmc read 0x806C0000 0x3600 0x20 " \
+ "&& esbc_validate 0x806C0000;env exists mcinitcmd " \
"&& fsl_mc lazyapply dpl 0x80001000;" \
"run distro_bootcmd;run sd_bootcmd;" \
"env exists secureboot && esbc_halt;"
#endif
+#endif /* CONFIG_TFABOOT */
/* MAC/PHY configuration */
#ifdef CONFIG_FSL_MC_ENET
-#define CONFIG_PHYLIB_10G
-#define CONFIG_PHY_GIGE
-#define CONFIG_PHYLIB
-
-#define CONFIG_PHY_VITESSE
-#define CONFIG_PHY_AQUANTIA
#define AQ_PHY_ADDR1 0x00
#define AQR105_IRQ_MASK 0x00000004
#endif
#endif
-/* MMC */
-#ifdef CONFIG_MMC
-#define CONFIG_SYS_FSL_MMC_HAS_CAPBLT_VS33
-#endif
-
#ifndef SPL_NO_ENV
#define BOOT_TARGET_DEVICES(func) \
func(MMC, mmc, 0) \
+ func(USB, usb, 0) \
func(SCSI, scsi, 0) \
func(DHCP, dhcp, na)
#include <config_distro_bootcmd.h>