/* SPDX-License-Identifier: GPL-2.0+ */
/*
- * Copyright 2017 NXP
+ * Copyright 2017, 2020-2021 NXP
*/
#ifndef __LS1088A_RDB_H
#include "ls1088a_common.h"
-#ifdef CONFIG_TFABOOT
-#define CONFIG_SYS_MMC_ENV_DEV 0
-
-#define CONFIG_ENV_SIZE 0x2000 /* 8KB */
-#define CONFIG_ENV_OFFSET 0x500000
-#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + \
- CONFIG_ENV_OFFSET)
-#define CONFIG_ENV_SECT_SIZE 0x40000
-#else
-#if defined(CONFIG_QSPI_BOOT)
-#define CONFIG_ENV_SIZE 0x2000 /* 8KB */
-#define CONFIG_ENV_SECT_SIZE 0x40000
-#elif defined(CONFIG_SD_BOOT)
-#define CONFIG_ENV_OFFSET (3 * 1024 * 1024)
-#define CONFIG_SYS_MMC_ENV_DEV 0
-#define CONFIG_ENV_SIZE 0x2000
-#else
-#define CONFIG_ENV_IS_IN_FLASH
-#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x300000)
-#define CONFIG_ENV_SECT_SIZE 0x20000
-#define CONFIG_ENV_SIZE 0x20000
-#endif
-#endif /* CONFIG_TFABOOT */
-
#if defined(CONFIG_TFABOOT) || \
defined(CONFIG_QSPI_BOOT) || defined(CONFIG_SD_BOOT_QSPI)
#ifndef CONFIG_SPL_BUILD
#define CONFIG_QIXIS_I2C_ACCESS
#endif
#define SYS_NO_FLASH
-#undef CONFIG_CMD_IMLS
#endif
#define CONFIG_SYS_CLK_FREQ 100000000
-#define CONFIG_DDR_CLK_FREQ 100000000
#define COUNTER_FREQUENCY_REAL 25000000 /* 25MHz */
#define COUNTER_FREQUENCY 25000000 /* 25MHz */
-#define CONFIG_DDR_SPD
#ifdef CONFIG_EMU
#define CONFIG_SYS_FSL_DDR_EMU
-#define CONFIG_SYS_MXC_I2C1_SPEED 40000000
-#define CONFIG_SYS_MXC_I2C2_SPEED 40000000
#else
-#define CONFIG_DDR_ECC
-#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER
#define CONFIG_MEM_INIT_VALUE 0xdeadbeef
#endif
#define SPD_EEPROM_ADDRESS 0x51
#endif
#endif
-#ifndef SPL_NO_IFC
-#define CONFIG_NAND_FSL_IFC
-#endif
-
#define CONFIG_SYS_NAND_MAX_ECCPOS 256
#define CONFIG_SYS_NAND_MAX_OOBFREE 2
| CSOR_NAND_SPRZ_64/* Spare size = 64 */ \
| CSOR_NAND_PB(64)) /*Pages Per Block = 64*/
-#define CONFIG_SYS_NAND_ONFI_DETECTION
-
/* ONFI NAND Flash mode0 Timing Params */
#define CONFIG_SYS_NAND_FTIM0 (FTIM0_NAND_TCCST(0x07) | \
FTIM0_NAND_TWP(0x18) | \
#define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND_BASE }
#define CONFIG_SYS_MAX_NAND_DEVICE 1
#define CONFIG_MTD_NAND_VERIFY_WRITE
-#define CONFIG_CMD_NAND
-
-#define CONFIG_SYS_NAND_BLOCK_SIZE (128 * 1024)
#ifndef SPL_NO_QIXIS
#define CONFIG_FSL_QIXIS
#define CONFIG_SYS_LS_MC_BOOT_TIMEOUT_MS 5000
-#define I2C_MUX_CH_VOL_MONITOR 0xA
+#define I2C_MUX_CH_VOL_MONITOR 0xA
/* Voltage monitor on channel 2*/
#define I2C_VOL_MONITOR_ADDR 0x63
#define I2C_VOL_MONITOR_BUS_V_OFFSET 0x2
#define CONFIG_VOL_MONITOR_LTC3882_SET
#define CONFIG_VOL_MONITOR_LTC3882_READ
-/* PM Bus commands code for LTC3882*/
-#define PMBUS_CMD_PAGE 0x0
-#define PMBUS_CMD_READ_VOUT 0x8B
-#define PMBUS_CMD_PAGE_PLUS_WRITE 0x05
-#define PMBUS_CMD_VOUT_COMMAND 0x21
-
#define PWM_CHANNEL0 0x0
/*
* RTC configuration
*/
#define RTC
-#define CONFIG_RTC_PCF8563 1
#define CONFIG_SYS_I2C_RTC_ADDR 0x51 /* Channel 3*/
-#define CONFIG_CMD_DATE
#endif
/* EEPROM */
-#define CONFIG_ID_EEPROM
#define CONFIG_SYS_I2C_EEPROM_NXID
#define CONFIG_SYS_EEPROM_BUS_NUM 0
-#define CONFIG_SYS_I2C_EEPROM_ADDR 0x57
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5
-
-#ifndef SPL_NO_QSPI
-/* QSPI device */
-#if defined(CONFIG_TFABOOT) || \
- defined(CONFIG_QSPI_BOOT) || defined(CONFIG_SD_BOOT_QSPI)
-#define FSL_QSPI_FLASH_SIZE (1 << 26)
-#define FSL_QSPI_FLASH_NUM 2
-#endif
-#endif
-
-#define CONFIG_CMD_MEMINFO
-#define CONFIG_SYS_MEMTEST_START 0x80000000
-#define CONFIG_SYS_MEMTEST_END 0x9fffffff
#ifdef CONFIG_SPL_BUILD
#define CONFIG_SYS_MONITOR_BASE CONFIG_SPL_TEXT_BASE
/* Initial environment variables */
#ifdef CONFIG_TFABOOT
#define QSPI_MC_INIT_CMD \
- "sf probe 0:0;sf read 0x80000000 0xA00000 0x100000;" \
- "sf read 0x80100000 0xE00000 0x100000;" \
+ "sf probe 0:0;sf read 0x80a00000 0xA00000 0x200000;" \
+ "sf read 0x80e00000 0xE00000 0x100000;" \
"env exists secureboot && " \
- "sf read 0x80700000 0x700000 0x40000 && " \
- "sf read 0x80740000 0x740000 0x40000 && " \
- "esbc_validate 0x80700000 && " \
- "esbc_validate 0x80740000 ;" \
- "fsl_mc start mc 0x80000000 0x80100000\0"
+ "sf read 0x80640000 0x640000 0x40000 && " \
+ "sf read 0x80680000 0x680000 0x40000 && " \
+ "esbc_validate 0x80640000 && " \
+ "esbc_validate 0x80680000 ;" \
+ "fsl_mc start mc 0x80a00000 0x80e00000\0"
#define SD_MC_INIT_CMD \
- "mmcinfo;mmc read 0x80000000 0x5000 0x800;" \
- "mmc read 0x80100000 0x7000 0x800;" \
+ "mmcinfo;mmc read 0x80a00000 0x5000 0x1000;" \
+ "mmc read 0x80e00000 0x7000 0x800;" \
"env exists secureboot && " \
- "mmc read 0x80700000 0x3800 0x10 && " \
- "mmc read 0x80740000 0x3A00 0x10 && " \
- "esbc_validate 0x80700000 && " \
- "esbc_validate 0x80740000 ;" \
- "fsl_mc start mc 0x80000000 0x80100000\0"
+ "mmc read 0x80640000 0x3200 0x20 && " \
+ "mmc read 0x80680000 0x3400 0x20 && " \
+ "esbc_validate 0x80640000 && " \
+ "esbc_validate 0x80680000 ;" \
+ "fsl_mc start mc 0x80a00000 0x80e00000\0"
#else
#if defined(CONFIG_QSPI_BOOT)
#define MC_INIT_CMD \
- "mcinitcmd=sf probe 0:0;sf read 0x80000000 0xA00000 0x100000;" \
- "sf read 0x80100000 0xE00000 0x100000;" \
+ "mcinitcmd=sf probe 0:0;sf read 0x80a00000 0xA00000 0x200000;" \
+ "sf read 0x80e00000 0xE00000 0x100000;" \
"env exists secureboot && " \
- "sf read 0x80700000 0x700000 0x40000 && " \
- "sf read 0x80740000 0x740000 0x40000 && " \
- "esbc_validate 0x80700000 && " \
- "esbc_validate 0x80740000 ;" \
- "fsl_mc start mc 0x80000000 0x80100000\0" \
+ "sf read 0x80640000 0x640000 0x40000 && " \
+ "sf read 0x80680000 0x680000 0x40000 && " \
+ "esbc_validate 0x80640000 && " \
+ "esbc_validate 0x80680000 ;" \
+ "fsl_mc start mc 0x80a00000 0x80e00000\0" \
"mcmemsize=0x70000000\0"
#elif defined(CONFIG_SD_BOOT)
#define MC_INIT_CMD \
- "mcinitcmd=mmcinfo;mmc read 0x80000000 0x5000 0x800;" \
- "mmc read 0x80100000 0x7000 0x800;" \
+ "mcinitcmd=mmcinfo;mmc read 0x80a00000 0x5000 0x1000;" \
+ "mmc read 0x80e00000 0x7000 0x800;" \
"env exists secureboot && " \
- "mmc read 0x80700000 0x3800 0x10 && " \
- "mmc read 0x80740000 0x3A00 0x10 && " \
- "esbc_validate 0x80700000 && " \
- "esbc_validate 0x80740000 ;" \
- "fsl_mc start mc 0x80000000 0x80100000\0" \
+ "mmc read 0x80640000 0x3200 0x20 && " \
+ "mmc read 0x80680000 0x3400 0x20 && " \
+ "esbc_validate 0x80640000 && " \
+ "esbc_validate 0x80680000 ;" \
+ "fsl_mc start mc 0x80a00000 0x80e00000\0" \
"mcmemsize=0x70000000\0"
#endif
#endif /* CONFIG_TFABOOT */
"fdt_addr=0x64f00000\0" \
"kernel_addr=0x1000000\0" \
"kernel_addr_sd=0x8000\0" \
- "kernelhdr_addr_sd=0x4000\0" \
+ "kernelhdr_addr_sd=0x3000\0" \
"kernel_start=0x580100000\0" \
- "kernelheader_start=0x580800000\0" \
+ "kernelheader_start=0x580600000\0" \
"scriptaddr=0x80000000\0" \
"scripthdraddr=0x80080000\0" \
"fdtheader_addr_r=0x80100000\0" \
- "kernelheader_addr=0x800000\0" \
+ "kernelheader_addr=0x600000\0" \
"kernelheader_addr_r=0x80200000\0" \
"kernel_addr_r=0x81000000\0" \
"kernelheader_size=0x40000\0" \
"load_addr=0xa0000000\0" \
"kernel_size=0x2800000\0" \
"kernel_size_sd=0x14000\0" \
- "kernelhdr_size_sd=0x10\0" \
+ "kernelhdr_size_sd=0x20\0" \
QSPI_MC_INIT_CMD \
"mcmemsize=0x70000000\0" \
BOOTENV \
"run scan_dev_for_boot; " \
"fi; " \
"done\0" \
- "scan_dev_for_boot=" \
- "echo Scanning ${devtype} " \
- "${devnum}:${distro_bootpart}...; " \
- "for prefix in ${boot_prefixes}; do " \
- "run scan_dev_for_scripts; " \
- "done;\0" \
"boot_a_script=" \
"load ${devtype} ${devnum}:${distro_bootpart} " \
"${scriptaddr} ${prefix}${script}; " \
"env exists secureboot && load ${devtype} " \
"${devnum}:${distro_bootpart} " \
- "${scripthdraddr} ${prefix}${boot_script_hdr} " \
+ "${scripthdraddr} ${prefix}${boot_script_hdr}; "\
+ "env exists secureboot " \
"&& esbc_validate ${scripthdraddr};" \
"source ${scriptaddr}\0" \
"installer=load mmc 0:2 $load_addr " \
"fdt_addr=0x64f00000\0" \
"kernel_addr=0x1000000\0" \
"kernel_addr_sd=0x8000\0" \
- "kernelhdr_addr_sd=0x4000\0" \
+ "kernelhdr_addr_sd=0x3000\0" \
"kernel_start=0x580100000\0" \
"kernelheader_start=0x580800000\0" \
"scriptaddr=0x80000000\0" \
"scripthdraddr=0x80080000\0" \
"fdtheader_addr_r=0x80100000\0" \
- "kernelheader_addr=0x800000\0" \
+ "kernelheader_addr=0x600000\0" \
"kernelheader_addr_r=0x80200000\0" \
"kernel_addr_r=0x81000000\0" \
"kernelheader_size=0x40000\0" \
"load_addr=0xa0000000\0" \
"kernel_size=0x2800000\0" \
"kernel_size_sd=0x14000\0" \
- "kernelhdr_size_sd=0x10\0" \
+ "kernelhdr_size_sd=0x20\0" \
MC_INIT_CMD \
BOOTENV \
"boot_scripts=ls1088ardb_boot.scr\0" \
"run scan_dev_for_boot; " \
"fi; " \
"done\0" \
- "scan_dev_for_boot=" \
- "echo Scanning ${devtype} " \
- "${devnum}:${distro_bootpart}...; " \
- "for prefix in ${boot_prefixes}; do " \
- "run scan_dev_for_scripts; " \
- "done;\0" \
"boot_a_script=" \
"load ${devtype} ${devnum}:${distro_bootpart} " \
"${scriptaddr} ${prefix}${script}; " \
#undef CONFIG_BOOTCOMMAND
#ifdef CONFIG_TFABOOT
#define QSPI_NOR_BOOTCOMMAND \
- "sf read 0x80001000 0xd00000 0x100000;" \
+ "sf read 0x80001000 0xd00000 0x100000;" \
"env exists mcinitcmd && env exists secureboot " \
- " && sf read 0x80780000 0x780000 0x100000 " \
- "&& esbc_validate 0x80780000;env exists mcinitcmd " \
+ " && sf read 0x806C0000 0x6C0000 0x100000 " \
+ "&& esbc_validate 0x806C0000;env exists mcinitcmd " \
"&& fsl_mc lazyapply dpl 0x80001000;" \
"run distro_bootcmd;run qspi_bootcmd;" \
"env exists secureboot && esbc_halt;"
"env exists mcinitcmd && mmcinfo; " \
"mmc read 0x80001000 0x6800 0x800; " \
"env exists mcinitcmd && env exists secureboot " \
- " && mmc read 0x80780000 0x3C00 0x10 " \
- "&& esbc_validate 0x80780000;env exists mcinitcmd " \
+ " && mmc read 0x806C0000 0x3600 0x20 " \
+ "&& esbc_validate 0x806C0000;env exists mcinitcmd " \
"&& fsl_mc lazyapply dpl 0x80001000;" \
"run distro_bootcmd;run sd_bootcmd;" \
"env exists secureboot && esbc_halt;"
#define CONFIG_BOOTCOMMAND \
"sf read 0x80001000 0xd00000 0x100000;" \
"env exists mcinitcmd && env exists secureboot " \
- " && sf read 0x80780000 0x780000 0x100000 " \
- "&& esbc_validate 0x80780000;env exists mcinitcmd " \
+ " && sf read 0x806C0000 0x6C0000 0x100000 " \
+ "&& esbc_validate 0x806C0000;env exists mcinitcmd " \
"&& fsl_mc lazyapply dpl 0x80001000;" \
"run distro_bootcmd;run qspi_bootcmd;" \
"env exists secureboot && esbc_halt;"
"env exists mcinitcmd && mmcinfo; " \
"mmc read 0x80001000 0x6800 0x800; " \
"env exists mcinitcmd && env exists secureboot " \
- " && mmc read 0x80780000 0x3C00 0x10 " \
- "&& esbc_validate 0x80780000;env exists mcinitcmd " \
+ " && mmc read 0x806C0000 0x3600 0x20 " \
+ "&& esbc_validate 0x806C0000;env exists mcinitcmd " \
"&& fsl_mc lazyapply dpl 0x80001000;" \
"run distro_bootcmd;run sd_bootcmd;" \
"env exists secureboot && esbc_halt;"
/* MAC/PHY configuration */
#ifdef CONFIG_FSL_MC_ENET
-#define CONFIG_PHYLIB
-
-#define CONFIG_PHY_VITESSE
#define AQ_PHY_ADDR1 0x00
#define AQR105_IRQ_MASK 0x00000004
#endif
#endif
-/* MMC */
-#ifdef CONFIG_MMC
-#define CONFIG_SYS_FSL_MMC_HAS_CAPBLT_VS33
-#endif
-
#ifndef SPL_NO_ENV
#define BOOT_TARGET_DEVICES(func) \
func(MMC, mmc, 0) \
+ func(USB, usb, 0) \
func(SCSI, scsi, 0) \
func(DHCP, dhcp, na)
#include <config_distro_bootcmd.h>
projects / platform / kernel / u-boot.git / blobdiff