#include "ls1088a_common.h"
+#ifndef SPL_NO_BOARDINFO
#define CONFIG_DISPLAY_BOARDINFO_LATE
+#endif
+
+#define CONFIG_MISC_INIT_R
#if defined(CONFIG_QSPI_BOOT)
#define CONFIG_ENV_SIZE 0x2000 /* 8KB */
-#define CONFIG_ENV_OFFSET 0x300000 /* 3MB */
#define CONFIG_ENV_SECT_SIZE 0x40000
+#elif defined(CONFIG_SD_BOOT)
+#define CONFIG_ENV_OFFSET (3 * 1024 * 1024)
+#define CONFIG_SYS_MMC_ENV_DEV 0
+#define CONFIG_ENV_SIZE 0x2000
#else
#define CONFIG_ENV_IS_IN_FLASH
#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x300000)
#define CONFIG_ENV_SIZE 0x20000
#endif
-#if defined(CONFIG_QSPI_BOOT)
+#if defined(CONFIG_QSPI_BOOT) || defined(CONFIG_SD_BOOT_QSPI)
+#ifndef CONFIG_SPL_BUILD
#define CONFIG_QIXIS_I2C_ACCESS
+#endif
#define SYS_NO_FLASH
+#undef CONFIG_CMD_IMLS
#endif
#define CONFIG_SYS_CLK_FREQ 100000000
#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE }
#endif
#endif
+
+#ifndef SPL_NO_IFC
+#define CONFIG_NAND_FSL_IFC
+#endif
+
#define CONFIG_SYS_NAND_MAX_ECCPOS 256
#define CONFIG_SYS_NAND_MAX_OOBFREE 2
#define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND_BASE }
#define CONFIG_SYS_MAX_NAND_DEVICE 1
#define CONFIG_MTD_NAND_VERIFY_WRITE
+#define CONFIG_CMD_NAND
#define CONFIG_SYS_NAND_BLOCK_SIZE (128 * 1024)
+#ifndef SPL_NO_QIXIS
#define CONFIG_FSL_QIXIS
+#endif
+
#define CONFIG_SYS_I2C_FPGA_ADDR 0x66
+#define QIXIS_BRDCFG4_OFFSET 0x54
#define QIXIS_LBMAP_SWITCH 2
#define QIXIS_QMAP_MASK 0xe0
#define QIXIS_QMAP_SHIFT 5
#define QIXIS_LBMAP_DFLTBANK 0x00
#define QIXIS_LBMAP_ALTBANK 0x20
#define QIXIS_LBMAP_SD 0x00
+#define QIXIS_LBMAP_EMMC 0x00
#define QIXIS_LBMAP_SD_QSPI 0x00
#define QIXIS_LBMAP_QSPI 0x00
#define QIXIS_RCW_SRC_SD 0x40
+#define QIXIS_RCW_SRC_EMMC 0x41
#define QIXIS_RCW_SRC_QSPI 0x62
#define QIXIS_RST_CTL_RESET 0x31
#define QIXIS_RCFG_CTL_RECONFIG_IDLE 0x20
#define CONFIG_SYS_LS_MC_BOOT_TIMEOUT_MS 5000
+#define I2C_MUX_CH_VOL_MONITOR 0xA
+/* Voltage monitor on channel 2*/
+#define I2C_VOL_MONITOR_ADDR 0x63
+#define I2C_VOL_MONITOR_BUS_V_OFFSET 0x2
+#define I2C_VOL_MONITOR_BUS_V_OVF 0x1
+#define I2C_VOL_MONITOR_BUS_V_SHIFT 3
+#define I2C_SVDD_MONITOR_ADDR 0x4F
+
+#define CONFIG_VID_FLS_ENV "ls1088ardb_vdd_mv"
+#define CONFIG_VID
+
+/* The lowest and highest voltage allowed for LS1088ARDB */
+#define VDD_MV_MIN 819
+#define VDD_MV_MAX 1212
+
+#define CONFIG_VOL_MONITOR_LTC3882_SET
+#define CONFIG_VOL_MONITOR_LTC3882_READ
+
+/* PM Bus commands code for LTC3882*/
+#define PMBUS_CMD_PAGE 0x0
+#define PMBUS_CMD_READ_VOUT 0x8B
+#define PMBUS_CMD_PAGE_PLUS_WRITE 0x05
+#define PMBUS_CMD_VOUT_COMMAND 0x21
+
+#define PWM_CHANNEL0 0x0
+
/*
* I2C bus multiplexer
*/
#define I2C_RETIMER_ADDR 0x18
#define I2C_MUX_CH_DEFAULT 0x8
#define I2C_MUX_CH5 0xD
+
+#ifndef SPL_NO_RTC
/*
* RTC configuration
*/
#define CONFIG_RTC_PCF8563 1
#define CONFIG_SYS_I2C_RTC_ADDR 0x51 /* Channel 3*/
#define CONFIG_CMD_DATE
+#endif
/* EEPROM */
#define CONFIG_ID_EEPROM
#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3
#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5
+#ifndef SPL_NO_QSPI
/* QSPI device */
-#if defined(CONFIG_QSPI_BOOT)
+#if defined(CONFIG_QSPI_BOOT) || defined(CONFIG_SD_BOOT_QSPI)
#define CONFIG_FSL_QSPI
-#define CONFIG_SPI_FLASH_SPANSION
#define FSL_QSPI_FLASH_SIZE (1 << 26)
#define FSL_QSPI_FLASH_NUM 2
#endif
+#endif
#define CONFIG_CMD_MEMINFO
-#define CONFIG_CMD_MEMTEST
#define CONFIG_SYS_MEMTEST_START 0x80000000
#define CONFIG_SYS_MEMTEST_END 0x9fffffff
+#ifdef CONFIG_SPL_BUILD
+#define CONFIG_SYS_MONITOR_BASE CONFIG_SPL_TEXT_BASE
+#else
#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
+#endif
#define CONFIG_FSL_MEMAC
+#ifndef SPL_NO_ENV
/* Initial environment variables */
#if defined(CONFIG_QSPI_BOOT)
+#define MC_INIT_CMD \
+ "mcinitcmd=sf probe 0:0;sf read 0x80000000 0xA00000 0x100000;" \
+ "sf read 0x80100000 0xE00000 0x100000;" \
+ "env exists secureboot && " \
+ "sf read 0x80700000 0x700000 0x40000 && " \
+ "sf read 0x80740000 0x740000 0x40000 && " \
+ "esbc_validate 0x80700000 && " \
+ "esbc_validate 0x80740000 ;" \
+ "fsl_mc start mc 0x80000000 0x80100000\0" \
+ "mcmemsize=0x70000000\0"
+#elif defined(CONFIG_SD_BOOT)
+#define MC_INIT_CMD \
+ "mcinitcmd=mmcinfo;mmc read 0x80000000 0x5000 0x800;" \
+ "mmc read 0x80100000 0x7000 0x800;" \
+ "env exists secureboot && " \
+ "mmc read 0x80700000 0x3800 0x10 && " \
+ "mmc read 0x80740000 0x3A00 0x10 && " \
+ "esbc_validate 0x80700000 && " \
+ "esbc_validate 0x80740000 ;" \
+ "fsl_mc start mc 0x80000000 0x80100000\0" \
+ "mcmemsize=0x70000000\0"
+#endif
+
#undef CONFIG_EXTRA_ENV_SETTINGS
#define CONFIG_EXTRA_ENV_SETTINGS \
+ "BOARD=ls1088ardb\0" \
"hwconfig=fsl_ddr:bank_intlv=auto\0" \
- "loadaddr=0x90100000\0" \
- "kernel_addr=0x100000\0" \
"ramdisk_addr=0x800000\0" \
"ramdisk_size=0x2000000\0" \
"fdt_high=0xa0000000\0" \
"initrd_high=0xffffffffffffffff\0" \
- "kernel_start=0x1000000\0" \
- "kernel_load=0xa0000000\0" \
+ "fdt_addr=0x64f00000\0" \
+ "kernel_addr=0x1000000\0" \
+ "kernel_addr_sd=0x8000\0" \
+ "kernelhdr_addr_sd=0x4000\0" \
+ "kernel_start=0x580100000\0" \
+ "kernelheader_start=0x580800000\0" \
+ "scriptaddr=0x80000000\0" \
+ "scripthdraddr=0x80080000\0" \
+ "fdtheader_addr_r=0x80100000\0" \
+ "kernelheader_addr=0x800000\0" \
+ "kernelheader_addr_r=0x80200000\0" \
+ "kernel_addr_r=0x81000000\0" \
+ "kernelheader_size=0x40000\0" \
+ "fdt_addr_r=0x90000000\0" \
+ "load_addr=0xa0000000\0" \
"kernel_size=0x2800000\0" \
- "mcinitcmd=sf probe 0:0;sf read 0x80000000 0xA00000 0x100000;" \
- "sf read 0x80100000 0xE00000 0x100000;" \
- "fsl_mc start mc 0x80000000 0x80100000\0" \
- "mcmemsize=0x70000000 \0"
-
+ "kernel_size_sd=0x14000\0" \
+ "kernelhdr_size_sd=0x10\0" \
+ MC_INIT_CMD \
+ BOOTENV \
+ "boot_scripts=ls1088ardb_boot.scr\0" \
+ "boot_script_hdr=hdr_ls1088ardb_bs.out\0" \
+ "scan_dev_for_boot_part=" \
+ "part list ${devtype} ${devnum} devplist; " \
+ "env exists devplist || setenv devplist 1; " \
+ "for distro_bootpart in ${devplist}; do " \
+ "if fstype ${devtype} " \
+ "${devnum}:${distro_bootpart} " \
+ "bootfstype; then " \
+ "run scan_dev_for_boot; " \
+ "fi; " \
+ "done\0" \
+ "scan_dev_for_boot=" \
+ "echo Scanning ${devtype} " \
+ "${devnum}:${distro_bootpart}...; " \
+ "for prefix in ${boot_prefixes}; do " \
+ "run scan_dev_for_scripts; " \
+ "done;\0" \
+ "boot_a_script=" \
+ "load ${devtype} ${devnum}:${distro_bootpart} " \
+ "${scriptaddr} ${prefix}${script}; " \
+ "env exists secureboot && load ${devtype} " \
+ "${devnum}:${distro_bootpart} " \
+ "${scripthdraddr} ${prefix}${boot_script_hdr} " \
+ "&& esbc_validate ${scripthdraddr};" \
+ "source ${scriptaddr}\0" \
+ "installer=load mmc 0:2 $load_addr " \
+ "/flex_installer_arm64.itb; " \
+ "env exists mcinitcmd && run mcinitcmd && " \
+ "mmc read 0x80200000 0x6800 0x800;" \
+ "fsl_mc apply dpl 0x80200000;" \
+ "bootm $load_addr#ls1088ardb\0" \
+ "qspi_bootcmd=echo Trying load from qspi..;" \
+ "sf probe && sf read $load_addr " \
+ "$kernel_addr $kernel_size ; env exists secureboot " \
+ "&& sf read $kernelheader_addr_r $kernelheader_addr " \
+ "$kernelheader_size && esbc_validate ${kernelheader_addr_r}; "\
+ "bootm $load_addr#$BOARD\0" \
+ "sd_bootcmd=echo Trying load from sd card..;" \
+ "mmcinfo; mmc read $load_addr " \
+ "$kernel_addr_sd $kernel_size_sd ;" \
+ "env exists secureboot && mmc read $kernelheader_addr_r "\
+ "$kernelhdr_addr_sd $kernelhdr_size_sd " \
+ " && esbc_validate ${kernelheader_addr_r};" \
+ "bootm $load_addr#$BOARD\0"
+
+#undef CONFIG_BOOTCOMMAND
+#if defined(CONFIG_QSPI_BOOT)
+/* Try to boot an on-QSPI kernel first, then do normal distro boot */
+#define CONFIG_BOOTCOMMAND \
+ "sf read 0x80200000 0xd00000 0x100000;" \
+ "env exists mcinitcmd && env exists secureboot " \
+ " && sf read 0x80780000 0x780000 0x100000 " \
+ "&& esbc_validate 0x80780000;env exists mcinitcmd " \
+ "&& fsl_mc apply dpl 0x80200000;" \
+ "run distro_bootcmd;run qspi_bootcmd;" \
+ "env exists secureboot && esbc_halt;"
+
+/* Try to boot an on-SD kernel first, then do normal distro boot */
+#elif defined(CONFIG_SD_BOOT)
+#define CONFIG_BOOTCOMMAND \
+ "env exists mcinitcmd && mmcinfo; " \
+ "mmc read 0x80200000 0x6800 0x800; " \
+ "env exists mcinitcmd && env exists secureboot " \
+ " && mmc read 0x80780000 0x3800 0x10 " \
+ "&& esbc_validate 0x80780000;env exists mcinitcmd " \
+ "&& fsl_mc apply dpl 0x80200000;" \
+ "run distro_bootcmd;run sd_bootcmd;" \
+ "env exists secureboot && esbc_halt;"
#endif
/* MAC/PHY configuration */
#define CONFIG_ETHPRIME "DPMAC1@xgmii"
#define CONFIG_PHY_GIGE
#endif
+#endif
/* MMC */
#ifdef CONFIG_MMC
#define CONFIG_SYS_FSL_MMC_HAS_CAPBLT_VS33
#endif
-#undef CONFIG_CMDLINE_EDITING
-#include <config_distro_defaults.h>
+#ifndef SPL_NO_ENV
#define BOOT_TARGET_DEVICES(func) \
- func(USB, usb, 0) \
func(MMC, mmc, 0) \
func(SCSI, scsi, 0) \
func(DHCP, dhcp, na)
#include <config_distro_bootcmd.h>
+#endif
#include <asm/fsl_secure_boot.h>
projects / platform / kernel / u-boot.git / blobdiff