#include "ls1088a_common.h"
-
-#ifndef __ASSEMBLY__
-unsigned long get_board_sys_clk(void);
-#endif
-
-#ifdef CONFIG_TFABOOT
-#define CONFIG_MISC_INIT_R
-#endif
-
#if defined(CONFIG_QSPI_BOOT) || defined(CONFIG_SD_BOOT_QSPI)
-#define CONFIG_QIXIS_I2C_ACCESS
#define SYS_NO_FLASH
-
-#define CONFIG_SYS_CLK_FREQ 100000000
-#else
-#define CONFIG_QIXIS_I2C_ACCESS
-#define CONFIG_SYS_CLK_FREQ get_board_sys_clk()
#endif
-#define COUNTER_FREQUENCY_REAL (CONFIG_SYS_CLK_FREQ/4)
-#define COUNTER_FREQUENCY 25000000 /* 25MHz */
-
-#define CONFIG_DIMM_SLOTS_PER_CTLR 1
+#define COUNTER_FREQUENCY_REAL (get_board_sys_clk()/4)
-#define CONFIG_DDR_SPD
-#define CONFIG_DDR_ECC
-#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER
#define CONFIG_MEM_INIT_VALUE 0xdeadbeef
#define SPD_EEPROM_ADDRESS 0x51
#define CONFIG_SYS_SPD_BUS_NUM 0
#define CONFIG_SYS_FLASH_QUIET_TEST
#define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */
-#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* number of banks */
#define CONFIG_SYS_MAX_FLASH_SECT 1024 /* sectors per device */
#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
#endif
#endif
-#define CONFIG_NAND_FSL_IFC
#define CONFIG_SYS_NAND_MAX_ECCPOS 256
#define CONFIG_SYS_NAND_MAX_OOBFREE 2
| CSOR_NAND_SPRZ_64/* Spare size = 64 */ \
| CSOR_NAND_PB(64)) /*Pages Per Block = 64*/
-#define CONFIG_SYS_NAND_ONFI_DETECTION
-
/* ONFI NAND Flash mode0 Timing Params */
#define CONFIG_SYS_NAND_FTIM0 (FTIM0_NAND_TCCST(0x07) | \
FTIM0_NAND_TWP(0x18) | \
#define CONFIG_SYS_MAX_NAND_DEVICE 1
#define CONFIG_MTD_NAND_VERIFY_WRITE
-#define CONFIG_SYS_NAND_BLOCK_SIZE (128 * 1024)
-
-#define CONFIG_FSL_QIXIS
#define CONFIG_SYS_I2C_FPGA_ADDR 0x66
#define QIXIS_LBMAP_SWITCH 6
#define QIXIS_QMAP_MASK 0xe0
#define I2C_VOL_MONITOR_BUS_V_SHIFT 3
#define I2C_SVDD_MONITOR_ADDR 0x4F
-#define CONFIG_VID_FLS_ENV "ls1088aqds_vdd_mv"
-#define CONFIG_VID
-
/* The lowest and highest voltage allowed for LS1088AQDS */
#define VDD_MV_MIN 819
#define VDD_MV_MAX 1212
-#define CONFIG_VOL_MONITOR_LTC3882_SET
-#define CONFIG_VOL_MONITOR_LTC3882_READ
-
#define PWM_CHANNEL0 0x0
/*
#define CONFIG_SYS_EEPROM_BUS_NUM 0
#ifdef CONFIG_FSL_DSPI
-#define CONFIG_SPI_FLASH_STMICRO
-#define CONFIG_SPI_FLASH_SST
-#define CONFIG_SPI_FLASH_EON
#if !defined(CONFIG_TFABOOT) && \
!defined(CONFIG_QSPI_BOOT) && !defined(CONFIG_SD_BOOT_QSPI)
#endif
#endif
-#ifdef CONFIG_SPL_BUILD
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SPL_TEXT_BASE
-#else
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
-#endif
-
#define CONFIG_FSL_MEMAC
/* MMC */
#define XQSGMII_CARD_PHY4_PORT2_ADDR 0xe
#define XQSGMII_CARD_PHY4_PORT3_ADDR 0xf
-#define CONFIG_ETHPRIME "DPMAC1@xgmii"
-#define CONFIG_PHY_GIGE /* Include GbE speed/duplex detection */
-
#endif
#define BOOT_TARGET_DEVICES(func) \