/* SPDX-License-Identifier: GPL-2.0+ */
/*
- * Copyright 2017, 2020 NXP
+ * Copyright 2017, 2020-2021 NXP
*/
#ifndef __LS1088A_QDS_H
#include "ls1088a_common.h"
-
-#ifndef __ASSEMBLY__
-unsigned long get_board_sys_clk(void);
-unsigned long get_board_ddr_clk(void);
-#endif
-
-#ifdef CONFIG_TFABOOT
-#define CONFIG_MISC_INIT_R
-#endif
-
#if defined(CONFIG_QSPI_BOOT) || defined(CONFIG_SD_BOOT_QSPI)
-#define CONFIG_QIXIS_I2C_ACCESS
#define SYS_NO_FLASH
-
-#define CONFIG_SYS_CLK_FREQ 100000000
-#define CONFIG_DDR_CLK_FREQ 100000000
-#else
-#define CONFIG_QIXIS_I2C_ACCESS
-#ifndef CONFIG_DM_I2C
-#define CONFIG_SYS_I2C_EARLY_INIT
-#endif
-#define CONFIG_SYS_CLK_FREQ get_board_sys_clk()
-#define CONFIG_DDR_CLK_FREQ get_board_ddr_clk()
#endif
-#define COUNTER_FREQUENCY_REAL (CONFIG_SYS_CLK_FREQ/4)
-#define COUNTER_FREQUENCY 25000000 /* 25MHz */
+#define COUNTER_FREQUENCY_REAL (get_board_sys_clk()/4)
-#define CONFIG_DIMM_SLOTS_PER_CTLR 1
-
-#define CONFIG_DDR_SPD
-#define CONFIG_DDR_ECC
-#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER
#define CONFIG_MEM_INIT_VALUE 0xdeadbeef
#define SPD_EEPROM_ADDRESS 0x51
-#define CONFIG_SYS_SPD_BUS_NUM 0
/*
#define CONFIG_SYS_IFC_CCR 0x01000000
#ifndef SYS_NO_FLASH
-#define CONFIG_SYS_FLASH_QUIET_TEST
#define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */
-#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* number of banks */
-#define CONFIG_SYS_MAX_FLASH_SECT 1024 /* sectors per device */
-#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
-#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
-
-#define CONFIG_SYS_FLASH_EMPTY_INFO
#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE,\
CONFIG_SYS_FLASH_BASE + 0x40000000}
#endif
#endif
-#define CONFIG_NAND_FSL_IFC
-#define CONFIG_SYS_NAND_MAX_ECCPOS 256
-#define CONFIG_SYS_NAND_MAX_OOBFREE 2
-
-#define CONFIG_SYS_NAND_CSPR_EXT (0x0)
-#define CONFIG_SYS_NAND_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \
+#define CFG_SYS_NAND_CSPR_EXT (0x0)
+#define CFG_SYS_NAND_CSPR (CSPR_PHYS_ADDR(CFG_SYS_NAND_BASE_PHYS) \
| CSPR_PORT_SIZE_8 /* Port Size = 8 bit */ \
| CSPR_MSEL_NAND /* MSEL = NAND */ \
| CSPR_V)
-#define CONFIG_SYS_NAND_AMASK IFC_AMASK(64 * 1024)
+#define CFG_SYS_NAND_AMASK IFC_AMASK(64 * 1024)
-#define CONFIG_SYS_NAND_CSOR (CSOR_NAND_ECC_ENC_EN /* ECC on encode */ \
+#define CFG_SYS_NAND_CSOR (CSOR_NAND_ECC_ENC_EN /* ECC on encode */ \
| CSOR_NAND_ECC_DEC_EN /* ECC on decode */ \
| CSOR_NAND_ECC_MODE_4 /* 4-bit ECC */ \
| CSOR_NAND_RAL_3 /* RAL = 3Byes */ \
| CSOR_NAND_SPRZ_64/* Spare size = 64 */ \
| CSOR_NAND_PB(64)) /*Pages Per Block = 64*/
-#define CONFIG_SYS_NAND_ONFI_DETECTION
-
/* ONFI NAND Flash mode0 Timing Params */
-#define CONFIG_SYS_NAND_FTIM0 (FTIM0_NAND_TCCST(0x07) | \
+#define CFG_SYS_NAND_FTIM0 (FTIM0_NAND_TCCST(0x07) | \
FTIM0_NAND_TWP(0x18) | \
FTIM0_NAND_TWCHT(0x07) | \
FTIM0_NAND_TWH(0x0a))
-#define CONFIG_SYS_NAND_FTIM1 (FTIM1_NAND_TADLE(0x32) | \
+#define CFG_SYS_NAND_FTIM1 (FTIM1_NAND_TADLE(0x32) | \
FTIM1_NAND_TWBE(0x39) | \
FTIM1_NAND_TRR(0x0e) | \
FTIM1_NAND_TRP(0x18))
-#define CONFIG_SYS_NAND_FTIM2 (FTIM2_NAND_TRAD(0x0f) | \
+#define CFG_SYS_NAND_FTIM2 (FTIM2_NAND_TRAD(0x0f) | \
FTIM2_NAND_TREH(0x0a) | \
FTIM2_NAND_TWHRE(0x1e))
-#define CONFIG_SYS_NAND_FTIM3 0x0
+#define CFG_SYS_NAND_FTIM3 0x0
-#define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND_BASE }
-#define CONFIG_SYS_MAX_NAND_DEVICE 1
+#define CFG_SYS_NAND_BASE_LIST { CFG_SYS_NAND_BASE }
#define CONFIG_MTD_NAND_VERIFY_WRITE
-#define CONFIG_SYS_NAND_BLOCK_SIZE (128 * 1024)
-
-#define CONFIG_FSL_QIXIS
#define CONFIG_SYS_I2C_FPGA_ADDR 0x66
#define QIXIS_LBMAP_SWITCH 6
#define QIXIS_QMAP_MASK 0xe0
#define CONFIG_SYS_CS1_FTIM1 CONFIG_SYS_NOR_FTIM1
#define CONFIG_SYS_CS1_FTIM2 CONFIG_SYS_NOR_FTIM2
#define CONFIG_SYS_CS1_FTIM3 CONFIG_SYS_NOR_FTIM3
-#define CONFIG_SYS_CSPR2_EXT CONFIG_SYS_NAND_CSPR_EXT
-#define CONFIG_SYS_CSPR2 CONFIG_SYS_NAND_CSPR
-#define CONFIG_SYS_AMASK2 CONFIG_SYS_NAND_AMASK
-#define CONFIG_SYS_CSOR2 CONFIG_SYS_NAND_CSOR
-#define CONFIG_SYS_CS2_FTIM0 CONFIG_SYS_NAND_FTIM0
-#define CONFIG_SYS_CS2_FTIM1 CONFIG_SYS_NAND_FTIM1
-#define CONFIG_SYS_CS2_FTIM2 CONFIG_SYS_NAND_FTIM2
-#define CONFIG_SYS_CS2_FTIM3 CONFIG_SYS_NAND_FTIM3
+#define CONFIG_SYS_CSPR2_EXT CFG_SYS_NAND_CSPR_EXT
+#define CONFIG_SYS_CSPR2 CFG_SYS_NAND_CSPR
+#define CONFIG_SYS_AMASK2 CFG_SYS_NAND_AMASK
+#define CONFIG_SYS_CSOR2 CFG_SYS_NAND_CSOR
+#define CONFIG_SYS_CS2_FTIM0 CFG_SYS_NAND_FTIM0
+#define CONFIG_SYS_CS2_FTIM1 CFG_SYS_NAND_FTIM1
+#define CONFIG_SYS_CS2_FTIM2 CFG_SYS_NAND_FTIM2
+#define CONFIG_SYS_CS2_FTIM3 CFG_SYS_NAND_FTIM3
#define CONFIG_SYS_CSPR3_EXT CONFIG_SYS_FPGA_CSPR_EXT
#define CONFIG_SYS_CSPR3 CONFIG_SYS_FPGA_CSPR
#define CONFIG_SYS_CSPR3_FINAL SYS_FPGA_CSPR_FINAL
#define CONFIG_SYS_CS3_FTIM3 SYS_FPGA_CS_FTIM3
#else
#if defined(CONFIG_QSPI_BOOT) || defined(CONFIG_SD_BOOT_QSPI)
-#define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_NAND_CSPR_EXT
-#define CONFIG_SYS_CSPR0 CONFIG_SYS_NAND_CSPR
-#define CONFIG_SYS_AMASK0 CONFIG_SYS_NAND_AMASK
-#define CONFIG_SYS_CSOR0 CONFIG_SYS_NAND_CSOR
-#define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NAND_FTIM0
-#define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NAND_FTIM1
-#define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NAND_FTIM2
-#define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NAND_FTIM3
+#define CONFIG_SYS_CSPR0_EXT CFG_SYS_NAND_CSPR_EXT
+#define CONFIG_SYS_CSPR0 CFG_SYS_NAND_CSPR
+#define CONFIG_SYS_AMASK0 CFG_SYS_NAND_AMASK
+#define CONFIG_SYS_CSOR0 CFG_SYS_NAND_CSOR
+#define CONFIG_SYS_CS0_FTIM0 CFG_SYS_NAND_FTIM0
+#define CONFIG_SYS_CS0_FTIM1 CFG_SYS_NAND_FTIM1
+#define CONFIG_SYS_CS0_FTIM2 CFG_SYS_NAND_FTIM2
+#define CONFIG_SYS_CS0_FTIM3 CFG_SYS_NAND_FTIM3
#define CONFIG_SYS_CSPR2_EXT CONFIG_SYS_FPGA_CSPR_EXT
#define CONFIG_SYS_CSPR2 CONFIG_SYS_FPGA_CSPR
#define CONFIG_SYS_CSPR2_FINAL SYS_FPGA_CSPR_FINAL
#define CONFIG_SYS_CS1_FTIM1 CONFIG_SYS_NOR_FTIM1
#define CONFIG_SYS_CS1_FTIM2 CONFIG_SYS_NOR_FTIM2
#define CONFIG_SYS_CS1_FTIM3 CONFIG_SYS_NOR_FTIM3
-#define CONFIG_SYS_CSPR2_EXT CONFIG_SYS_NAND_CSPR_EXT
-#define CONFIG_SYS_CSPR2 CONFIG_SYS_NAND_CSPR
-#define CONFIG_SYS_AMASK2 CONFIG_SYS_NAND_AMASK
-#define CONFIG_SYS_CSOR2 CONFIG_SYS_NAND_CSOR
-#define CONFIG_SYS_CS2_FTIM0 CONFIG_SYS_NAND_FTIM0
-#define CONFIG_SYS_CS2_FTIM1 CONFIG_SYS_NAND_FTIM1
-#define CONFIG_SYS_CS2_FTIM2 CONFIG_SYS_NAND_FTIM2
-#define CONFIG_SYS_CS2_FTIM3 CONFIG_SYS_NAND_FTIM3
+#define CONFIG_SYS_CSPR2_EXT CFG_SYS_NAND_CSPR_EXT
+#define CONFIG_SYS_CSPR2 CFG_SYS_NAND_CSPR
+#define CONFIG_SYS_AMASK2 CFG_SYS_NAND_AMASK
+#define CONFIG_SYS_CSOR2 CFG_SYS_NAND_CSOR
+#define CONFIG_SYS_CS2_FTIM0 CFG_SYS_NAND_FTIM0
+#define CONFIG_SYS_CS2_FTIM1 CFG_SYS_NAND_FTIM1
+#define CONFIG_SYS_CS2_FTIM2 CFG_SYS_NAND_FTIM2
+#define CONFIG_SYS_CS2_FTIM3 CFG_SYS_NAND_FTIM3
#define CONFIG_SYS_CSPR3_EXT CONFIG_SYS_FPGA_CSPR_EXT
#define CONFIG_SYS_CSPR3 CONFIG_SYS_FPGA_CSPR
#define CONFIG_SYS_CSPR3_FINAL SYS_FPGA_CSPR_FINAL
#define I2C_VOL_MONITOR_BUS_V_SHIFT 3
#define I2C_SVDD_MONITOR_ADDR 0x4F
-#define CONFIG_VID_FLS_ENV "ls1088aqds_vdd_mv"
-#define CONFIG_VID
-
/* The lowest and highest voltage allowed for LS1088AQDS */
#define VDD_MV_MIN 819
#define VDD_MV_MAX 1212
-#define CONFIG_VOL_MONITOR_LTC3882_SET
-#define CONFIG_VOL_MONITOR_LTC3882_READ
-
-/* PM Bus commands code for LTC3882*/
-#define PMBUS_CMD_PAGE 0x0
-#define PMBUS_CMD_READ_VOUT 0x8B
-#define PMBUS_CMD_PAGE_PLUS_WRITE 0x05
-#define PMBUS_CMD_VOUT_COMMAND 0x21
-
#define PWM_CHANNEL0 0x0
/*
#define RTC
#define CONFIG_SYS_I2C_RTC_ADDR 0x51 /* Channel 3*/
-/* EEPROM */
-#define CONFIG_ID_EEPROM
-#define CONFIG_SYS_I2C_EEPROM_NXID
-#define CONFIG_SYS_EEPROM_BUS_NUM 0
-#define CONFIG_SYS_I2C_EEPROM_ADDR 0x57
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5
-
#ifdef CONFIG_FSL_DSPI
-#define CONFIG_SPI_FLASH_STMICRO
-#define CONFIG_SPI_FLASH_SST
-#define CONFIG_SPI_FLASH_EON
#if !defined(CONFIG_TFABOOT) && \
!defined(CONFIG_QSPI_BOOT) && !defined(CONFIG_SD_BOOT_QSPI)
#endif
#endif
-#ifdef CONFIG_SPL_BUILD
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SPL_TEXT_BASE
-#else
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
-#endif
-
-#define CONFIG_FSL_MEMAC
-
-/* MMC */
-#define CONFIG_SYS_FSL_MMC_HAS_CAPBLT_VS33
-#define CONFIG_ESDHC_DETECT_QUIRK ((readb(QIXIS_BASE + QIXIS_STAT_PRES1) & \
- QIXIS_SDID_MASK) != QIXIS_ESDHC_NO_ADAPTER)
-
#define COMMON_ENV \
"kernelheader_addr_r=0x80200000\0" \
"fdtheader_addr_r=0x80100000\0" \
"kernel_start=0x1000000\0" \
"kernel_load=0xa0000000\0" \
"kernel_size=0x2800000\0" \
- "mcinitcmd=sf probe 0:0;sf read 0xa0a00000 0xa00000 0x100000;" \
+ "mcinitcmd=sf probe 0:0;sf read 0xa0a00000 0xa00000 0x200000;" \
"sf read 0xa0640000 0x640000 0x4000; esbc_validate 0xa0640000;" \
"sf read 0xa0e00000 0xe00000 0x100000;" \
"sf read 0xa0680000 0x680000 0x4000;esbc_validate 0xa0680000;" \
#else /* if !(CONFIG_NXP_ESBC) */
#ifdef CONFIG_TFABOOT
#define QSPI_MC_INIT_CMD \
- "sf probe 0:0;sf read 0x80000000 0xA00000 0x100000;" \
- "sf read 0x80100000 0xE00000 0x100000;" \
- "fsl_mc start mc 0x80000000 0x80100000\0"
+ "sf probe 0:0;sf read 0x80a00000 0xA00000 0x200000;" \
+ "sf read 0x80e00000 0xE00000 0x100000;" \
+ "fsl_mc start mc 0x80a00000 0x80e00000\0"
#define SD_MC_INIT_CMD \
- "mmcinfo;mmc read 0x80000000 0x5000 0x800;" \
- "mmc read 0x80100000 0x7000 0x800;" \
- "fsl_mc start mc 0x80000000 0x80100000\0"
+ "mmcinfo;mmc read 0x80a00000 0x5000 0x1000;" \
+ "mmc read 0x80e00000 0x7000 0x800;" \
+ "fsl_mc start mc 0x80a00000 0x80e00000\0"
#define IFC_MC_INIT_CMD \
"fsl_mc start mc 0x580A00000 0x580E00000\0"
"kernel_load=0xa0000000\0" \
"kernel_size=0x2800000\0" \
"kernel_size_sd=0x14000\0" \
- "mcinitcmd=sf probe 0:0;sf read 0x80000000 0xA00000 0x100000;" \
- "sf read 0x80100000 0xE00000 0x100000;" \
- "fsl_mc start mc 0x80000000 0x80100000\0" \
+ "mcinitcmd=sf probe 0:0;sf read 0x80a00000 0xA00000 0x200000;" \
+ "sf read 0x80e00000 0xE00000 0x100000;" \
+ "fsl_mc start mc 0x80a00000 0x80e00000\0" \
"mcmemsize=0x70000000 \0" \
"BOARD=ls1088aqds\0" \
"scriptaddr=0x80000000\0" \
"kernel_start=0x1000000\0" \
"kernel_load=0xa0000000\0" \
"kernel_size=0x2800000\0" \
- "mcinitcmd=sf probe 0:0;sf read 0x80000000 0xA00000 0x100000;" \
- "sf read 0x80100000 0xE00000 0x100000;" \
- "fsl_mc start mc 0x80000000 0x80100000\0" \
+ "mcinitcmd=sf probe 0:0;sf read 0x80a00000 0xA00000 0x200000;" \
+ "sf read 0x80e00000 0xE00000 0x100000;" \
+ "fsl_mc start mc 0x80a00000 0x80e00000\0" \
"mcmemsize=0x70000000 \0"
#elif defined(CONFIG_SD_BOOT)
#undef CONFIG_EXTRA_ENV_SETTINGS
"kernel_start=0x8000\0" \
"kernel_load=0xa0000000\0" \
"kernel_size=0x14000\0" \
- "mcinitcmd=mmcinfo;mmc read 0x80000000 0x5000 0x800;" \
- "mmc read 0x80100000 0x7000 0x800;" \
- "fsl_mc start mc 0x80000000 0x80100000\0" \
+ "mcinitcmd=mmcinfo;mmc read 0x80a00000 0x5000 0x1000;" \
+ "mmc read 0x80e00000 0x7000 0x800;" \
+ "fsl_mc start mc 0x80a00000 0x80e00000\0" \
"mcmemsize=0x70000000 \0"
#else /* NOR BOOT */
#undef CONFIG_EXTRA_ENV_SETTINGS
#endif
#ifdef CONFIG_FSL_MC_ENET
-#define CONFIG_FSL_MEMAC
#define RGMII_PHY1_ADDR 0x1
#define RGMII_PHY2_ADDR 0x2
#define SGMII_CARD_PORT1_PHY_ADDR 0x1C
#define XQSGMII_CARD_PHY4_PORT2_ADDR 0xe
#define XQSGMII_CARD_PHY4_PORT3_ADDR 0xf
-#define CONFIG_ETHPRIME "DPMAC1@xgmii"
-#define CONFIG_PHY_GIGE /* Include GbE speed/duplex detection */
-
#endif
#define BOOT_TARGET_DEVICES(func) \
projects / platform / kernel / u-boot.git / blobdiff