#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_FSL_OCRAM_BASE + 0xfff0)
/* Link Definitions */
+#ifdef CONFIG_SPL
+#define CONFIG_SYS_TEXT_BASE 0x80400000
+#else
#ifdef CONFIG_QSPI_BOOT
#define CONFIG_SYS_TEXT_BASE 0x20100000
#else
#define CONFIG_SYS_TEXT_BASE 0x30100000
#endif
+#endif
#define CONFIG_SUPPORT_RAW_INITRD
#define CONFIG_SKIP_LOWLEVEL_INIT
+#if !defined(CONFIG_SD_BOOT)
#define CONFIG_FSL_DDR_INTERACTIVE /* Interactive debugging */
+#endif
#define CONFIG_VERY_BIG_RAM
#define CONFIG_SYS_DDR_SDRAM_BASE 0x80000000UL
#define CONFIG_SYS_LS_MC_DRAM_DPL_OFFSET 0x00F20000
#define CONFIG_SYS_LS_MC_AIOP_IMG_MAX_LENGTH 0x200000
#define CONFIG_SYS_LS_MC_DRAM_AIOP_IMG_OFFSET 0x07000000
+
+/* Define phy_reset function to boot the MC based on mcinitcmd.
+ * This happens late enough to properly fixup u-boot env MAC addresses.
+ */
+#define CONFIG_RESET_PHY_R
+
/*
* Carve out a DDR region which will not be used by u-boot/Linux
*
#if defined(CONFIG_FSL_MC_ENET)
#define CONFIG_SYS_LS_MC_DRAM_BLOCK_MIN_SIZE (512UL * 1024 * 1024)
#endif
-
-#define CONFIG_FSL_CAAM /* Enable SEC/CAAM */
-
/* Command line configuration */
#define CONFIG_CMD_GREPENV
#define CONFIG_CMD_CACHE
/* Miscellaneous configurable options */
#define CONFIG_SYS_LOAD_ADDR (CONFIG_SYS_DDR_SDRAM_BASE + 0x10000000)
+/* SATA */
+#ifdef CONFIG_SCSI
+#define CONFIG_SCSI_AHCI_PLAT
+#define CONFIG_SYS_SATA1 AHCI_BASE_ADDR1
+
+#define CONFIG_SYS_SCSI_MAX_SCSI_ID 1
+#define CONFIG_SYS_SCSI_MAX_LUN 1
+#define CONFIG_SYS_SCSI_MAX_DEVICE (CONFIG_SYS_SCSI_MAX_SCSI_ID * \
+ CONFIG_SYS_SCSI_MAX_LUN)
+#endif
+
/* Physical Memory Map */
#define CONFIG_CHIP_SELECTS_PER_CTRL 4
" fsl_mc apply dpl 0x80200000 &&" \
" sf read $kernel_load $kernel_start" \
" $kernel_size && bootm $kernel_load"
+#elif defined(CONFIG_SD_BOOT)
+#define CONFIG_BOOTCOMMAND "mmcinfo;mmc read 0x80200000 0x6800 0x800;"\
+ " fsl_mc apply dpl 0x80200000 &&" \
+ " mmc read $kernel_load $kernel_start" \
+ " $kernel_size && bootm $kernel_load"
#else /* NOR BOOT*/
#define CONFIG_BOOTCOMMAND "fsl_mc apply dpl 0x580d00000 &&" \
" cp.b $kernel_start $kernel_load" \
#define CONFIG_AUTO_COMPLETE
#define CONFIG_SYS_MAXARGS 64 /* max command args */
-#define CONFIG_PANIC_HANG /* do not reset board on panic */
-
+#ifdef CONFIG_SPL
+#define CONFIG_SPL_BSS_START_ADDR 0x80100000
+#define CONFIG_SPL_BSS_MAX_SIZE 0x00100000
+#define CONFIG_SPL_FRAMEWORK
+#define CONFIG_SPL_LDSCRIPT "arch/arm/cpu/armv8/u-boot-spl.lds"
+#define CONFIG_SPL_MAX_SIZE 0x16000
+#define CONFIG_SPL_STACK (CONFIG_SYS_FSL_OCRAM_BASE + 0x9ff0)
+#define CONFIG_SPL_TARGET "u-boot-with-spl.bin"
+#define CONFIG_SPL_TEXT_BASE 0x1800a000
+
+#define CONFIG_SYS_SPL_MALLOC_SIZE 0x00100000
+#define CONFIG_SYS_SPL_MALLOC_START 0x80200000
+#define CONFIG_SYS_MONITOR_LEN (512 * 1024)
+#endif
#define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */
#endif /* __LS1088_COMMON_H */