#define SPL_NO_SATA
#define SPL_NO_QSPI
#define SPL_NO_IFC
-#undef CONFIG_DISPLAY_CPUINFO
#endif
-#define CONFIG_REMAKE_ELF
-
#include <asm/arch/stream_id_lsch3.h>
#include <asm/arch/config.h>
#include <asm/arch/soc.h>
#define LS1088ARDB_PB_BOARD 0x4A
/* Link Definitions */
-#ifdef CONFIG_TFABOOT
-#define CONFIG_SYS_INIT_SP_ADDR CONFIG_SYS_TEXT_BASE
-#else
-#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_FSL_OCRAM_BASE + 0xfff0)
-#endif
/* Link Definitions */
#define CONFIG_SYS_FSL_QSPI_BASE 0x20000000
#define CPU_RELEASE_ADDR secondary_boot_addr
/* GPIO */
-#ifdef CONFIG_DM_GPIO
-#ifndef CONFIG_MPC8XXX_GPIO
-#define CONFIG_MPC8XXX_GPIO
-#endif
-#endif
/* I2C */
#define CONFIG_SYS_NS16550_REG_SIZE 1
#define CONFIG_SYS_NS16550_CLK (get_bus_freq(0) / 2)
-#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
-
-#if !defined(SPL_NO_IFC) || defined(CONFIG_TARGET_LS1088AQDS)
-/* IFC */
-#define CONFIG_FSL_IFC
-#endif
-
/*
* During booting, IFC is mapped at the region of 0x30000000.
* But this region is limited to 256MB. To accommodate NOR, promjet
#define CONFIG_SYS_LS_MC_AIOP_IMG_MAX_LENGTH 0x200000
#define CONFIG_SYS_LS_MC_DRAM_AIOP_IMG_OFFSET 0x07000000
-/* Define phy_reset function to boot the MC based on mcinitcmd.
- * This happens late enough to properly fixup u-boot env MAC addresses.
- */
-#define CONFIG_RESET_PHY_R
-
/*
* Carve out a DDR region which will not be used by u-boot/Linux
*
/* Miscellaneous configurable options */
-/* SATA */
-#ifdef CONFIG_SCSI
-#define CONFIG_SCSI_AHCI_PLAT
-#define CONFIG_SYS_SATA1 AHCI_BASE_ADDR1
-
-#define CONFIG_SYS_SCSI_MAX_SCSI_ID 1
-#define CONFIG_SYS_SCSI_MAX_LUN 1
-#define CONFIG_SYS_SCSI_MAX_DEVICE (CONFIG_SYS_SCSI_MAX_SCSI_ID * \
- CONFIG_SYS_SCSI_MAX_LUN)
-#endif
-
/* Physical Memory Map */
-#define CONFIG_CHIP_SELECTS_PER_CTRL 4
#define CONFIG_HWCONFIG
#define HWCONFIG_BUFFER_SIZE 128
-/* #define CONFIG_DISPLAY_CPUINFO */
-
#ifndef SPL_NO_ENV
/* Initial environment variables */
#define CONFIG_EXTRA_ENV_SETTINGS \
"console=ttyAMA0,38400n8\0" \
"mcinitcmd=fsl_mc start mc 0x580a00000" \
" 0x580e00000 \0"
-
-#ifndef CONFIG_TFABOOT
-#if defined(CONFIG_QSPI_BOOT)
-#define CONFIG_BOOTCOMMAND "sf probe 0:0;" \
- "sf read 0x80001000 0xd00000 0x100000;"\
- " fsl_mc lazyapply dpl 0x80001000 &&" \
- " sf read $kernel_load $kernel_start" \
- " $kernel_size && bootm $kernel_load"
-#elif defined(CONFIG_SD_BOOT)
-#define CONFIG_BOOTCOMMAND "mmcinfo;mmc read 0x80001000 0x6800 0x800;"\
- " fsl_mc lazyapply dpl 0x80001000 &&" \
- " mmc read $kernel_load $kernel_start" \
- " $kernel_size && bootm $kernel_load"
-#else /* NOR BOOT*/
-#define CONFIG_BOOTCOMMAND "fsl_mc lazyapply dpl 0x580d00000 &&" \
- " cp.b $kernel_start $kernel_load" \
- " $kernel_size && bootm $kernel_load"
#endif
-#endif /* CONFIG_TFABOOT */
-#endif
-
-/* Monitor Command Prompt */
-#define CONFIG_SYS_CBSIZE 512 /* Console I/O Buffer Size */
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \
- sizeof(CONFIG_SYS_PROMPT) + 16)
-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot args buffer */
-#define CONFIG_SYS_MAXARGS 64 /* max command args */
#ifdef CONFIG_SPL
-#define CONFIG_SPL_BSS_START_ADDR 0x80100000
-#define CONFIG_SPL_BSS_MAX_SIZE 0x00100000
-#define CONFIG_SPL_LDSCRIPT "arch/arm/cpu/armv8/u-boot-spl.lds"
-#define CONFIG_SPL_MAX_SIZE 0x16000
-#define CONFIG_SPL_STACK (CONFIG_SYS_FSL_OCRAM_BASE + 0x9ff0)
-#define CONFIG_SPL_TARGET "u-boot-with-spl.bin"
-
-#define CONFIG_SYS_SPL_MALLOC_SIZE 0x00100000
-#define CONFIG_SYS_SPL_MALLOC_START 0x80200000
-
#ifdef CONFIG_NXP_ESBC
#define CONFIG_U_BOOT_HDR_SIZE (16 << 10)
/*
#endif /* ifdef CONFIG_NXP_ESBC */
#endif
-#define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */
#endif /* __LS1088_COMMON_H */