#define SPL_NO_SATA
#define SPL_NO_QSPI
#define SPL_NO_IFC
-#undef CONFIG_DISPLAY_CPUINFO
#endif
-#define CONFIG_REMAKE_ELF
-
#include <asm/arch/stream_id_lsch3.h>
#include <asm/arch/config.h>
#include <asm/arch/soc.h>
/* Link Definitions */
#define CONFIG_SYS_FSL_QSPI_BASE 0x20000000
-#define CONFIG_SKIP_LOWLEVEL_INIT
-
#define CONFIG_VERY_BIG_RAM
#define CONFIG_SYS_DDR_SDRAM_BASE 0x80000000UL
#define CONFIG_SYS_FSL_DDR_SDRAM_BASE_PHY 0
/*
* SMP Definitinos
*/
-#define CPU_RELEASE_ADDR secondary_boot_func
-
-#ifdef CONFIG_PCI
-#define CONFIG_CMD_PCI
-#endif
+#define CPU_RELEASE_ADDR secondary_boot_addr
-/* Size of malloc() pool */
-#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 2048 * 1024)
+/* GPIO */
/* I2C */
-#ifndef CONFIG_DM_I2C
-#define CONFIG_SYS_I2C
-#endif
/* Serial Port */
#define CONFIG_SYS_NS16550_REG_SIZE 1
#define CONFIG_SYS_NS16550_CLK (get_bus_freq(0) / 2)
-#define CONFIG_BAUDRATE 115200
-#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
-
-#if !defined(SPL_NO_IFC) || defined(CONFIG_TARGET_LS1088AQDS)
-/* IFC */
-#define CONFIG_FSL_IFC
-#endif
-
/*
* During booting, IFC is mapped at the region of 0x30000000.
* But this region is limited to 256MB. To accommodate NOR, promjet
#define CONFIG_SYS_LS_MC_AIOP_IMG_MAX_LENGTH 0x200000
#define CONFIG_SYS_LS_MC_DRAM_AIOP_IMG_OFFSET 0x07000000
-/* Define phy_reset function to boot the MC based on mcinitcmd.
- * This happens late enough to properly fixup u-boot env MAC addresses.
- */
-#define CONFIG_RESET_PHY_R
-
/*
* Carve out a DDR region which will not be used by u-boot/Linux
*
#if defined(CONFIG_FSL_MC_ENET)
#define CONFIG_SYS_LS_MC_DRAM_BLOCK_MIN_SIZE (128UL * 1024 * 1024)
#endif
-/* Command line configuration */
-#define CONFIG_CMD_CACHE
/* Miscellaneous configurable options */
-#define CONFIG_SYS_LOAD_ADDR (CONFIG_SYS_DDR_SDRAM_BASE + 0x10000000)
/* SATA */
#ifdef CONFIG_SCSI
-#define CONFIG_SCSI_AHCI_PLAT
#define CONFIG_SYS_SATA1 AHCI_BASE_ADDR1
-
-#define CONFIG_SYS_SCSI_MAX_SCSI_ID 1
-#define CONFIG_SYS_SCSI_MAX_LUN 1
-#define CONFIG_SYS_SCSI_MAX_DEVICE (CONFIG_SYS_SCSI_MAX_SCSI_ID * \
- CONFIG_SYS_SCSI_MAX_LUN)
#endif
/* Physical Memory Map */
-#define CONFIG_CHIP_SELECTS_PER_CTRL 4
#define CONFIG_HWCONFIG
#define HWCONFIG_BUFFER_SIZE 128
-/* #define CONFIG_DISPLAY_CPUINFO */
-
#ifndef SPL_NO_ENV
-/* Allow to overwrite serial and ethaddr */
-#define CONFIG_ENV_OVERWRITE
-
/* Initial environment variables */
#define CONFIG_EXTRA_ENV_SETTINGS \
"hwconfig=fsl_ddr:bank_intlv=auto\0" \
"console=ttyAMA0,38400n8\0" \
"mcinitcmd=fsl_mc start mc 0x580a00000" \
" 0x580e00000 \0"
-
-#ifndef CONFIG_TFABOOT
-#if defined(CONFIG_QSPI_BOOT)
-#define CONFIG_BOOTCOMMAND "sf probe 0:0;" \
- "sf read 0x80001000 0xd00000 0x100000;"\
- " fsl_mc lazyapply dpl 0x80001000 &&" \
- " sf read $kernel_load $kernel_start" \
- " $kernel_size && bootm $kernel_load"
-#elif defined(CONFIG_SD_BOOT)
-#define CONFIG_BOOTCOMMAND "mmcinfo;mmc read 0x80001000 0x6800 0x800;"\
- " fsl_mc lazyapply dpl 0x80001000 &&" \
- " mmc read $kernel_load $kernel_start" \
- " $kernel_size && bootm $kernel_load"
-#else /* NOR BOOT*/
-#define CONFIG_BOOTCOMMAND "fsl_mc lazyapply dpl 0x580d00000 &&" \
- " cp.b $kernel_start $kernel_load" \
- " $kernel_size && bootm $kernel_load"
-#endif
-#endif /* CONFIG_TFABOOT */
#endif
/* Monitor Command Prompt */
#ifdef CONFIG_SPL
#define CONFIG_SPL_BSS_START_ADDR 0x80100000
#define CONFIG_SPL_BSS_MAX_SIZE 0x00100000
-#define CONFIG_SPL_LDSCRIPT "arch/arm/cpu/armv8/u-boot-spl.lds"
#define CONFIG_SPL_MAX_SIZE 0x16000
#define CONFIG_SPL_STACK (CONFIG_SYS_FSL_OCRAM_BASE + 0x9ff0)
#define CONFIG_SPL_TARGET "u-boot-with-spl.bin"