configs: Finish migration of PHY_GIGE

[platform/kernel/u-boot.git] / include / configs / ls1043ardb.h

diff --git a/include/configs/ls1043ardb.h b/include/configs/ls1043ardb.h
index 1d0a1ac..a4162a6 100644 (file)
--- a/include/configs/ls1043ardb.h
+++ b/include/configs/ls1043ardb.h
@@ -9,17 +9,6 @@
 
 #include "ls1043a_common.h"
 
-#if defined(CONFIG_FSL_LS_PPA)
-#define CONFIG_ARMV8_SEC_FIRMWARE_SUPPORT
-#define SEC_FIRMWARE_ERET_ADDR_REVERT
-#define CONFIG_ARMV8_PSCI
-
-#define CONFIG_SYS_LS_PPA_FW_IN_XIP
-#ifdef CONFIG_SYS_LS_PPA_FW_IN_XIP
-#define        CONFIG_SYS_LS_PPA_FW_ADDR       0x60500000
-#endif
-#endif
-
 #if defined(CONFIG_NAND_BOOT) || defined(CONFIG_SD_BOOT)
 #define CONFIG_SYS_TEXT_BASE           0x82000000
 #else
@@ -40,7 +29,9 @@
 #define CONFIG_SYS_SPD_BUS_NUM         0
 
 #define CONFIG_FSL_DDR_BIST
+#ifndef CONFIG_SPL
 #define CONFIG_FSL_DDR_INTERACTIVE     /* Interactive debugging */
+#endif
 #define CONFIG_SYS_DDR_RAW_TIMING
 #define CONFIG_ECC_INIT_VIA_DDRCONTROLLER
 #define CONFIG_MEM_INIT_VALUE           0xdeadbeef
@@ -99,7 +90,9 @@
 /*
  * NAND Flash Definitions
  */
+#ifndef SPL_NO_IFC
 #define CONFIG_NAND_FSL_IFC
+#endif
 
 #define CONFIG_SYS_NAND_BASE           0x7e800000
 #define CONFIG_SYS_NAND_BASE_PHYS      CONFIG_SYS_NAND_BASE
@@ -136,14 +129,13 @@
 #define CONFIG_SYS_NAND_BASE_LIST      { CONFIG_SYS_NAND_BASE }
 #define CONFIG_SYS_MAX_NAND_DEVICE     1
 #define CONFIG_MTD_NAND_VERIFY_WRITE
-#define CONFIG_CMD_NAND
 
 #define CONFIG_SYS_NAND_BLOCK_SIZE     (128 * 1024)
 
 #ifdef CONFIG_NAND_BOOT
 #define CONFIG_SPL_PAD_TO              0x20000         /* block aligned */
 #define CONFIG_SYS_NAND_U_BOOT_OFFS    CONFIG_SPL_PAD_TO
-#define CONFIG_SYS_NAND_U_BOOT_SIZE    (640 << 10)
+#define CONFIG_SYS_NAND_U_BOOT_SIZE    (1024 << 10)
 #endif
 
 /*
@@ -222,6 +214,7 @@
 #define CONFIG_SYS_CS2_FTIM3           CONFIG_SYS_CPLD_FTIM3
 
 /* EEPROM */
+#ifndef SPL_NO_EEPROM
 #define CONFIG_ID_EEPROM
 #define CONFIG_SYS_I2C_EEPROM_NXID
 #define CONFIG_SYS_EEPROM_BUS_NUM              0
@@ -229,39 +222,41 @@
 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN         1
 #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS      3
 #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS  5
+#endif
 
 /*
  * Environment
  */
+#ifndef SPL_NO_ENV
 #define CONFIG_ENV_OVERWRITE
+#endif
 
 #if defined(CONFIG_NAND_BOOT)
-#define CONFIG_ENV_IS_IN_NAND
 #define CONFIG_ENV_SIZE                        0x2000
-#define CONFIG_ENV_OFFSET              (10 * CONFIG_SYS_NAND_BLOCK_SIZE)
+#define CONFIG_ENV_OFFSET              (24 * CONFIG_SYS_NAND_BLOCK_SIZE)
 #elif defined(CONFIG_SD_BOOT)
-#define CONFIG_ENV_OFFSET              (1024 * 1024)
-#define CONFIG_ENV_IS_IN_MMC
+#define CONFIG_ENV_OFFSET              (3 * 1024 * 1024)
 #define CONFIG_SYS_MMC_ENV_DEV         0
 #define CONFIG_ENV_SIZE                        0x2000
 #else
-#define CONFIG_ENV_IS_IN_FLASH
-#define CONFIG_ENV_ADDR                        (CONFIG_SYS_FLASH_BASE + 0x200000)
+#define CONFIG_ENV_ADDR                        (CONFIG_SYS_FLASH_BASE + 0x300000)
 #define CONFIG_ENV_SECT_SIZE           0x20000
 #define CONFIG_ENV_SIZE                        0x20000
 #endif
 
 /* FMan */
-#ifdef CONFIG_SYS_DPAA_FMAN
-#define CONFIG_FMAN_ENET
-#define CONFIG_PHYLIB
-#define CONFIG_PHYLIB_10G
-#define CONFIG_PHY_GIGE                /* Include GbE speed/duplex detection */
+#ifndef SPL_NO_FMAN
+#define AQR105_IRQ_MASK                        0x40000000
 
+#ifdef CONFIG_NET
 #define CONFIG_PHY_VITESSE
 #define CONFIG_PHY_REALTEK
+#endif
+
+#ifdef CONFIG_SYS_DPAA_FMAN
+#define CONFIG_FMAN_ENET
+#define CONFIG_PHYLIB_10G
 #define CONFIG_PHY_AQUANTIA
-#define AQR105_IRQ_MASK                        0x40000000
 
 #define RGMII_PHY1_ADDR                        0x1
 #define RGMII_PHY2_ADDR                        0x2
@@ -275,34 +270,32 @@
 
 #define CONFIG_ETHPRIME                        "FM1@DTSEC3"
 #endif
+#endif
 
 /* QE */
-#if !defined(CONFIG_SD_BOOT) && !defined(CONFIG_NAND_BOOT) && \
-       !defined(CONFIG_QSPI_BOOT)
+#ifndef SPL_NO_QE
+#if !defined(CONFIG_NAND_BOOT) && !defined(CONFIG_QSPI_BOOT)
 #define CONFIG_U_QE
 #endif
-#define CONFIG_SYS_QE_FW_ADDR     0x60600000
+#endif
 
 /* USB */
+#ifndef SPL_NO_USB
 #define CONFIG_HAS_FSL_XHCI_USB
 #ifdef CONFIG_HAS_FSL_XHCI_USB
 #define CONFIG_USB_XHCI_FSL
 #define CONFIG_USB_MAX_CONTROLLER_COUNT                3
-#define CONFIG_SYS_USB_XHCI_MAX_ROOT_PORTS     2
+#endif
 #endif
 
 /* SATA */
+#ifndef SPL_NO_SATA
 #define CONFIG_LIBATA
 #define CONFIG_SCSI_AHCI
 #define CONFIG_CMD_SCSI
-#ifndef CONFIG_CMD_FAT
-#define CONFIG_CMD_FAT
-#endif
 #ifndef CONFIG_CMD_EXT2
 #define CONFIG_CMD_EXT2
 #endif
-#define CONFIG_DOS_PARTITION
-#define CONFIG_BOARD_LATE_INIT
 #define CONFIG_SYS_SCSI_MAX_SCSI_ID            2
 #define CONFIG_SYS_SCSI_MAX_LUN                        2
 #define CONFIG_SYS_SCSI_MAX_DEVICE             (CONFIG_SYS_SCSI_MAX_SCSI_ID * \
@@ -310,7 +303,7 @@
 #define SCSI_VEND_ID 0x1b4b
 #define SCSI_DEV_ID  0x9170
 #define CONFIG_SCSI_DEV_LIST {SCSI_VEND_ID, SCSI_DEV_ID}
-#define CONFIG_PCI
+#endif
 
 #include <asm/fsl_secure_boot.h>