#include "ls1043a_common.h"
-#define CONFIG_DISPLAY_CPUINFO
-#define CONFIG_DISPLAY_BOARDINFO
-
#if defined(CONFIG_NAND_BOOT) || defined(CONFIG_SD_BOOT)
#define CONFIG_SYS_TEXT_BASE 0x82000000
#elif defined(CONFIG_QSPI_BOOT)
-#define CONFIG_SYS_TEXT_BASE 0x40010000
+#define CONFIG_SYS_TEXT_BASE 0x40100000
#else
#define CONFIG_SYS_TEXT_BASE 0x60100000
#endif
#define SPD_EEPROM_ADDRESS 0x51
#define CONFIG_SYS_SPD_BUS_NUM 0
+#ifndef CONFIG_SPL
#define CONFIG_FSL_DDR_INTERACTIVE /* Interactive debugging */
-#ifndef CONFIG_SYS_FSL_DDR4
-#define CONFIG_SYS_FSL_DDR3 /* Use DDR3 memory */
#endif
#define CONFIG_DDR_ECC
#define CONFIG_MEM_INIT_VALUE 0xdeadbeef
#endif
-#define CONFIG_SYS_HAS_SERDES
-
#ifdef CONFIG_SYS_DPAA_FMAN
#define CONFIG_FMAN_ENET
-#define CONFIG_PHYLIB
#define CONFIG_PHY_VITESSE
#define CONFIG_PHY_REALTEK
#define CONFIG_PHYLIB_10G
#define CONFIG_LIBATA
#define CONFIG_SCSI_AHCI
#define CONFIG_SCSI_AHCI_PLAT
-#define CONFIG_SCSI
-#define CONFIG_DOS_PARTITION
-#define CONFIG_BOARD_LATE_INIT
/* EEPROM */
#define CONFIG_ID_EEPROM
#define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND_BASE }
#define CONFIG_SYS_MAX_NAND_DEVICE 1
#define CONFIG_MTD_NAND_VERIFY_WRITE
-#define CONFIG_CMD_NAND
#define CONFIG_SYS_NAND_BLOCK_SIZE (128 * 1024)
#endif
#if defined(CONFIG_QSPI_BOOT) || defined(CONFIG_SD_BOOT_QSPI)
#define CONFIG_QIXIS_I2C_ACCESS
#define CONFIG_SYS_I2C_EARLY_INIT
-#define CONFIG_SYS_NO_FLASH
#endif
/*
#ifdef CONFIG_HAS_FSL_XHCI_USB
#define CONFIG_USB_XHCI_FSL
#define CONFIG_USB_MAX_CONTROLLER_COUNT 3
-#define CONFIG_SYS_USB_XHCI_MAX_ROOT_PORTS 2
#endif
/*
#define CONFIG_SYS_HZ 1000
-/*
- * Stack sizes
- * The stack sizes are set up in start.S using the settings below
- */
-#define CONFIG_STACKSIZE (30 * 1024)
-
#define CONFIG_SYS_INIT_SP_OFFSET \
(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
#define CONFIG_ENV_OVERWRITE
#ifdef CONFIG_NAND_BOOT
-#define CONFIG_ENV_IS_IN_NAND
#define CONFIG_ENV_SIZE 0x2000
-#define CONFIG_ENV_OFFSET (10 * CONFIG_SYS_NAND_BLOCK_SIZE)
+#define CONFIG_ENV_OFFSET (24 * CONFIG_SYS_NAND_BLOCK_SIZE)
#elif defined(CONFIG_SD_BOOT)
-#define CONFIG_ENV_OFFSET (1024 * 1024)
-#define CONFIG_ENV_IS_IN_MMC
+#define CONFIG_ENV_OFFSET (3 * 1024 * 1024)
#define CONFIG_SYS_MMC_ENV_DEV 0
#define CONFIG_ENV_SIZE 0x2000
#elif defined(CONFIG_QSPI_BOOT)
-#define CONFIG_ENV_IS_IN_SPI_FLASH
#define CONFIG_ENV_SIZE 0x2000 /* 8KB */
-#define CONFIG_ENV_OFFSET 0x100000 /* 1MB */
+#define CONFIG_ENV_OFFSET 0x300000 /* 3MB */
#define CONFIG_ENV_SECT_SIZE 0x10000
#else
-#define CONFIG_ENV_IS_IN_FLASH
-#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x200000)
+#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x300000)
#define CONFIG_ENV_SECT_SIZE 0x20000
#define CONFIG_ENV_SIZE 0x20000
#endif