#include "ls1043a_common.h"
-#ifndef __ASSEMBLY__
-unsigned long get_board_sys_clk(void);
-unsigned long get_board_ddr_clk(void);
-#endif
-
-#define CONFIG_SYS_CLK_FREQ get_board_sys_clk()
-#define CONFIG_DDR_CLK_FREQ get_board_ddr_clk()
-
-#define CONFIG_SKIP_LOWLEVEL_INIT
-
-#define CONFIG_LAYERSCAPE_NS_ACCESS
-
-#define CONFIG_DIMM_SLOTS_PER_CTLR 1
/* Physical Memory Map */
-#define CONFIG_CHIP_SELECTS_PER_CTRL 4
-#define CONFIG_DDR_SPD
#define SPD_EEPROM_ADDRESS 0x51
-#define CONFIG_SYS_SPD_BUS_NUM 0
-#define CONFIG_DDR_ECC
#ifdef CONFIG_DDR_ECC
-#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER
#define CONFIG_MEM_INIT_VALUE 0xdeadbeef
#endif
#define QSGMII_CARD_PORT4_PHY_ADDR_S2 0xB
#endif
-#ifdef CONFIG_RAMBOOT_PBL
-#define CONFIG_SYS_FSL_PBL_PBI board/freescale/ls1043aqds/ls1043aqds_pbi.cfg
-#endif
-
-#ifdef CONFIG_NAND_BOOT
-#define CONFIG_SYS_FSL_PBL_RCW board/freescale/ls1043aqds/ls1043aqds_rcw_nand.cfg
-#endif
-
-#ifdef CONFIG_SD_BOOT
-#ifdef CONFIG_SD_BOOT_QSPI
-#define CONFIG_SYS_FSL_PBL_RCW \
- board/freescale/ls1043aqds/ls1043aqds_rcw_sd_qspi.cfg
-#else
-#define CONFIG_SYS_FSL_PBL_RCW board/freescale/ls1043aqds/ls1043aqds_rcw_sd_ifc.cfg
-#endif
-#endif
-
-/* LPUART */
-#ifdef CONFIG_LPUART
-#define CONFIG_LPUART_32B_REG
-#endif
-
/* SATA */
-#define CONFIG_SCSI_AHCI_PLAT
-
-/* EEPROM */
-#define CONFIG_SYS_I2C_EEPROM_NXID
-#define CONFIG_SYS_EEPROM_BUS_NUM 0
#define CONFIG_SYS_SATA AHCI_BASE_ADDR
-#define CONFIG_SYS_SCSI_MAX_SCSI_ID 1
-#define CONFIG_SYS_SCSI_MAX_LUN 1
-#define CONFIG_SYS_SCSI_MAX_DEVICE (CONFIG_SYS_SCSI_MAX_SCSI_ID * \
- CONFIG_SYS_SCSI_MAX_LUN)
-
/*
* IFC Definitions
*/
FTIM2_NOR_TWP(0x1c))
#define CONFIG_SYS_NOR_FTIM3 0
-#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */
-#define CONFIG_SYS_MAX_FLASH_SECT 1024 /* sectors per device */
-#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
-#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
-
-#define CONFIG_SYS_FLASH_EMPTY_INFO
#define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE_PHYS, \
CONFIG_SYS_FLASH_BASE_PHYS + 0x8000000}
-#define CONFIG_CFI_FLASH_USE_WEAK_ACCESSORS
#define CONFIG_SYS_WRITE_SWAPPED_DATA
/*
* NAND Flash Definitions
*/
-#define CONFIG_NAND_FSL_IFC
#define CONFIG_SYS_NAND_BASE 0x7e800000
#define CONFIG_SYS_NAND_BASE_PHYS CONFIG_SYS_NAND_BASE
| CSOR_NAND_SPRZ_64 /* Spare size = 64 */ \
| CSOR_NAND_PB(64)) /* 64 Pages Per Block */
-#define CONFIG_SYS_NAND_ONFI_DETECTION
-
#define CONFIG_SYS_NAND_FTIM0 (FTIM0_NAND_TCCST(0x7) | \
FTIM0_NAND_TWP(0x18) | \
FTIM0_NAND_TWCHT(0x7) | \
#define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND_BASE }
#define CONFIG_SYS_MAX_NAND_DEVICE 1
#define CONFIG_MTD_NAND_VERIFY_WRITE
-
-#define CONFIG_SYS_NAND_BLOCK_SIZE (128 * 1024)
#endif
#ifdef CONFIG_NAND_BOOT
-#define CONFIG_SPL_PAD_TO 0x20000 /* block aligned */
-#define CONFIG_SYS_NAND_U_BOOT_OFFS CONFIG_SPL_PAD_TO
#define CONFIG_SYS_NAND_U_BOOT_SIZE (640 << 10)
#endif
#if defined(CONFIG_TFABOOT) || \
defined(CONFIG_QSPI_BOOT) || defined(CONFIG_SD_BOOT_QSPI)
-#define CONFIG_QIXIS_I2C_ACCESS
#endif
/*
* QIXIS Definitions
*/
-#define CONFIG_FSL_QIXIS
#ifdef CONFIG_FSL_QIXIS
#define QIXIS_BASE 0x7fb00000
#define I2C_VOL_MONITOR_BUS_V_OVF 0x1
#define I2C_VOL_MONITOR_BUS_V_SHIFT 3
-#define CONFIG_VID_FLS_ENV "ls1043aqds_vdd_mv"
-#ifndef CONFIG_SPL_BUILD
-#define CONFIG_VID
-#endif
-#define CONFIG_VOL_MONITOR_IR36021_SET
-#define CONFIG_VOL_MONITOR_INA220
/* The lowest and highest voltage allowed for LS1043AQDS */
#define VDD_MV_MIN 819
#define VDD_MV_MAX 1212
* Miscellaneous configurable options
*/
-#define CONFIG_SYS_HZ 1000
-
-#define CONFIG_SYS_INIT_SP_OFFSET \
- (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-
-#ifdef CONFIG_SPL_BUILD
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SPL_TEXT_BASE
-#else
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */
-#endif
-
/*
* Environment
*/
-#define CONFIG_CMDLINE_TAG
-
#include <asm/fsl_secure_boot.h>
#endif /* __LS1043AQDS_H__ */