#ifndef __LS1043A_COMMON_H
#define __LS1043A_COMMON_H
+/* SPL build */
+#ifdef CONFIG_SPL_BUILD
+#define SPL_NO_FMAN
+#define SPL_NO_DSPI
+#define SPL_NO_PCIE
+#define SPL_NO_ENV
+#define SPL_NO_MISC
+#define SPL_NO_USB
+#define SPL_NO_SATA
+#define SPL_NO_QE
+#define SPL_NO_EEPROM
+#endif
+#if (defined(CONFIG_SPL_BUILD) && defined(CONFIG_NAND_BOOT))
+#define SPL_NO_MMC
+#endif
+#if (defined(CONFIG_SPL_BUILD) && defined(CONFIG_SD_BOOT))
+#define SPL_NO_IFC
+#endif
+
#define CONFIG_REMAKE_ELF
#define CONFIG_FSL_LAYERSCAPE
-#define CONFIG_LS1043A
#define CONFIG_MP
#define CONFIG_GICV2
#define CONFIG_SPL_TARGET "u-boot-with-spl.bin"
#define CONFIG_SPL_TEXT_BASE 0x10000000
-#define CONFIG_SPL_MAX_SIZE 0x1d000
+#define CONFIG_SPL_MAX_SIZE 0x17000
#define CONFIG_SPL_STACK 0x1001e000
#define CONFIG_SPL_PAD_TO 0x1d000
#define CONFIG_SYS_SPL_MALLOC_SIZE 0x100000
#define CONFIG_SPL_BSS_START_ADDR 0x80100000
#define CONFIG_SPL_BSS_MAX_SIZE 0x80000
-#define CONFIG_SYS_MONITOR_LEN 0xa0000
+
+#ifdef CONFIG_SECURE_BOOT
+#define CONFIG_U_BOOT_HDR_SIZE (16 << 10)
+/*
+ * HDR would be appended at end of image and copied to DDR along
+ * with U-Boot image. Here u-boot max. size is 512K. So if binary
+ * size increases then increase this size in case of secure boot as
+ * it uses raw u-boot image instead of fit image.
+ */
+#define CONFIG_SYS_MONITOR_LEN (0x100000 + CONFIG_U_BOOT_HDR_SIZE)
+#else
+#define CONFIG_SYS_MONITOR_LEN 0x100000
+#endif /* ifdef CONFIG_SECURE_BOOT */
#endif
/* NAND SPL */
#define CONFIG_SPL_BSS_START_ADDR 0x80100000
#define CONFIG_SYS_SPL_MALLOC_SIZE 0x100000
#define CONFIG_SPL_BSS_MAX_SIZE 0x80000
-#define CONFIG_SYS_MONITOR_LEN 0xa0000
+
+#ifdef CONFIG_SECURE_BOOT
+#define CONFIG_U_BOOT_HDR_SIZE (16 << 10)
+#endif /* ifdef CONFIG_SECURE_BOOT */
+
+#ifdef CONFIG_U_BOOT_HDR_SIZE
+/*
+ * HDR would be appended at end of image and copied to DDR along
+ * with U-Boot image. Here u-boot max. size is 512K. So if binary
+ * size increases then increase this size in case of secure boot as
+ * it uses raw u-boot image instead of fit image.
+ */
+#define CONFIG_SYS_MONITOR_LEN (0x100000 + CONFIG_U_BOOT_HDR_SIZE)
+#else
+#define CONFIG_SYS_MONITOR_LEN 0x100000
+#endif /* ifdef CONFIG_U_BOOT_HDR_SIZE */
+
#endif
/* IFC */
+#ifndef SPL_NO_IFC
#if !defined(CONFIG_QSPI_BOOT) && !defined(CONFIG_SD_BOOT_QSPI)
#define CONFIG_FSL_IFC
/*
#define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */
#endif
#endif
+#endif
/* I2C */
#define CONFIG_SYS_I2C
#define CONFIG_SYS_I2C_MXC_I2C4
/* PCIe */
+#ifndef SPL_NO_PCIE
#define CONFIG_PCIE1 /* PCIE controller 1 */
#define CONFIG_PCIE2 /* PCIE controller 2 */
#define CONFIG_PCIE3 /* PCIE controller 3 */
#define CONFIG_PCI_SCAN_SHOW
#define CONFIG_CMD_PCI
#endif
+#endif
/* Command line configuration */
-#define CONFIG_CMD_ENV
/* MMC */
+#ifndef SPL_NO_MMC
#ifdef CONFIG_MMC
#define CONFIG_FSL_ESDHC
#define CONFIG_SYS_FSL_MMC_HAS_CAPBLT_VS33
#endif
+#endif
/* DSPI */
+#ifndef SPL_NO_DSPI
#define CONFIG_FSL_DSPI
#ifdef CONFIG_FSL_DSPI
#define CONFIG_DM_SPI_FLASH
#define CONFIG_SF_DEFAULT_CS 0
#endif
#endif
+#endif
/* FMan ucode */
+#ifndef SPL_NO_FMAN
#define CONFIG_SYS_DPAA_FMAN
#ifdef CONFIG_SYS_DPAA_FMAN
#define CONFIG_SYS_FM_MURAM_SIZE 0x60000
#ifdef CONFIG_NAND_BOOT
-/* Store Fman ucode at offeset 0x160000(11 blocks). */
+/* Store Fman ucode at offeset 0x900000(72 blocks). */
#define CONFIG_SYS_QE_FMAN_FW_IN_NAND
-#define CONFIG_SYS_FMAN_FW_ADDR (11 * CONFIG_SYS_NAND_BLOCK_SIZE)
+#define CONFIG_SYS_FMAN_FW_ADDR (72 * CONFIG_SYS_NAND_BLOCK_SIZE)
#elif defined(CONFIG_SD_BOOT)
/*
* PBL SD boot image should stored at 0x1000(8 blocks), the size of the image is
* about 1MB (2040 blocks), Env is stored after the image, and the env size is
- * 0x2000 (16 blocks), 8 + 2040 + 16 = 2064, enlarge it to 2080(0x820).
+ * 0x2000 (16 blocks), 8 + 2040 + 16 = 2064, enlarge it to 18432(0x4800).
*/
#define CONFIG_SYS_QE_FMAN_FW_IN_MMC
-#define CONFIG_SYS_FMAN_FW_ADDR (512 * 0x820)
+#define CONFIG_SYS_FMAN_FW_ADDR (512 * 0x4800)
+#define CONFIG_SYS_QE_FW_ADDR (512 * 0x4a08)
#elif defined(CONFIG_QSPI_BOOT)
#define CONFIG_SYS_QE_FW_IN_SPIFLASH
-#define CONFIG_SYS_FMAN_FW_ADDR 0x400d0000
+#define CONFIG_SYS_FMAN_FW_ADDR 0x40900000
#define CONFIG_ENV_SPI_BUS 0
#define CONFIG_ENV_SPI_CS 0
#define CONFIG_ENV_SPI_MAX_HZ 1000000
#else
#define CONFIG_SYS_QE_FMAN_FW_IN_NOR
/* FMan fireware Pre-load address */
-#define CONFIG_SYS_FMAN_FW_ADDR 0x60300000
+#define CONFIG_SYS_FMAN_FW_ADDR 0x60900000
+#define CONFIG_SYS_QE_FW_ADDR 0x60940000
#endif
#define CONFIG_SYS_QE_FMAN_FW_LENGTH 0x10000
#define CONFIG_SYS_FDT_PAD (0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH)
#endif
+#endif
/* Miscellaneous configurable options */
#define CONFIG_SYS_LOAD_ADDR (CONFIG_SYS_DDR_SDRAM_BASE + 0x10000000)
#define CONFIG_HWCONFIG
#define HWCONFIG_BUFFER_SIZE 128
+#ifndef SPL_NO_MISC
#if defined(CONFIG_QSPI_BOOT) || defined(CONFIG_SD_BOOT_QSPI)
#define MTDPARTS_DEFAULT "mtdparts=spi0.0:1m(uboot)," \
"5m(kernel),1m(dtb),9m(file_system)"
#define CONFIG_BOOTCOMMAND "cp.b $kernel_start $kernel_load " \
"$kernel_size && bootm $kernel_load"
#endif
+#endif
/* Monitor Command Prompt */
#define CONFIG_SYS_CBSIZE 512 /* Console I/O Buffer Size */
sizeof(CONFIG_SYS_PROMPT) + 16)
#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot args buffer */
#define CONFIG_SYS_LONGHELP
+
+#ifndef SPL_NO_MISC
#define CONFIG_CMDLINE_EDITING 1
+#endif
+
#define CONFIG_AUTO_COMPLETE
#define CONFIG_SYS_MAXARGS 64 /* max command args */
#define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */
-/* Hash command with SHA acceleration supported in hardware */
-#ifdef CONFIG_FSL_CAAM
-#define CONFIG_CMD_HASH
-#define CONFIG_SHA_HW_ACCEL
-#endif
+#include <asm/arch/soc.h>
#endif /* __LS1043A_COMMON_H */