#ifndef __LS1043A_COMMON_H
#define __LS1043A_COMMON_H
+/* SPL build */
+#ifdef CONFIG_SPL_BUILD
+#define SPL_NO_FMAN
+#define SPL_NO_DSPI
+#define SPL_NO_PCIE
+#define SPL_NO_ENV
+#define SPL_NO_MISC
+#define SPL_NO_USB
+#define SPL_NO_SATA
+#define SPL_NO_QE
+#define SPL_NO_EEPROM
+#endif
+#if (defined(CONFIG_SPL_BUILD) && defined(CONFIG_NAND_BOOT))
+#define SPL_NO_MMC
+#endif
+#if (defined(CONFIG_SPL_BUILD) && defined(CONFIG_SD_BOOT_QSPI))
+#define SPL_NO_IFC
+#endif
+
#define CONFIG_REMAKE_ELF
#define CONFIG_FSL_LAYERSCAPE
-#define CONFIG_LS1043A
#define CONFIG_MP
#define CONFIG_GICV2
+#include <asm/arch/stream_id_lsch2.h>
#include <asm/arch/config.h>
/* Link Definitions */
#define CONFIG_SUPPORT_RAW_INITRD
#define CONFIG_SKIP_LOWLEVEL_INIT
-#define CONFIG_BOARD_EARLY_INIT_F 1
#define CONFIG_VERY_BIG_RAM
#define CONFIG_SYS_DDR_SDRAM_BASE 0x80000000
#define CONFIG_SYS_NS16550_REG_SIZE 1
#define CONFIG_SYS_NS16550_CLK (get_serial_clock())
-#define CONFIG_BAUDRATE 115200
#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
/* SD boot SPL */
#ifdef CONFIG_SD_BOOT
#define CONFIG_SPL_FRAMEWORK
-#define CONFIG_SPL_LDSCRIPT "arch/arm/cpu/armv8/u-boot-spl.lds"
#define CONFIG_SPL_TARGET "u-boot-with-spl.bin"
#define CONFIG_SPL_TEXT_BASE 0x10000000
-#define CONFIG_SPL_MAX_SIZE 0x1d000
+#define CONFIG_SPL_MAX_SIZE 0x17000
#define CONFIG_SPL_STACK 0x1001e000
#define CONFIG_SPL_PAD_TO 0x1d000
#define CONFIG_SYS_SPL_MALLOC_SIZE 0x100000
#define CONFIG_SPL_BSS_START_ADDR 0x80100000
#define CONFIG_SPL_BSS_MAX_SIZE 0x80000
-#define CONFIG_SYS_MONITOR_LEN 0xa0000
+
+#ifdef CONFIG_SECURE_BOOT
+#define CONFIG_U_BOOT_HDR_SIZE (16 << 10)
+/*
+ * HDR would be appended at end of image and copied to DDR along
+ * with U-Boot image. Here u-boot max. size is 512K. So if binary
+ * size increases then increase this size in case of secure boot as
+ * it uses raw u-boot image instead of fit image.
+ */
+#define CONFIG_SYS_MONITOR_LEN (0x100000 + CONFIG_U_BOOT_HDR_SIZE)
+#else
+#define CONFIG_SYS_MONITOR_LEN 0x100000
+#endif /* ifdef CONFIG_SECURE_BOOT */
#endif
/* NAND SPL */
#ifdef CONFIG_NAND_BOOT
#define CONFIG_SPL_PBL_PAD
#define CONFIG_SPL_FRAMEWORK
-#define CONFIG_SPL_LDSCRIPT "arch/arm/cpu/armv8/u-boot-spl.lds"
#define CONFIG_SPL_TARGET "u-boot-with-spl.bin"
#define CONFIG_SPL_TEXT_BASE 0x10000000
#define CONFIG_SPL_MAX_SIZE 0x1a000
#define CONFIG_SPL_BSS_START_ADDR 0x80100000
#define CONFIG_SYS_SPL_MALLOC_SIZE 0x100000
#define CONFIG_SPL_BSS_MAX_SIZE 0x80000
-#define CONFIG_SYS_MONITOR_LEN 0xa0000
+
+#ifdef CONFIG_SECURE_BOOT
+#define CONFIG_U_BOOT_HDR_SIZE (16 << 10)
+#endif /* ifdef CONFIG_SECURE_BOOT */
+
+#ifdef CONFIG_U_BOOT_HDR_SIZE
+/*
+ * HDR would be appended at end of image and copied to DDR along
+ * with U-Boot image. Here u-boot max. size is 512K. So if binary
+ * size increases then increase this size in case of secure boot as
+ * it uses raw u-boot image instead of fit image.
+ */
+#define CONFIG_SYS_MONITOR_LEN (0x100000 + CONFIG_U_BOOT_HDR_SIZE)
+#else
+#define CONFIG_SYS_MONITOR_LEN 0x100000
+#endif /* ifdef CONFIG_U_BOOT_HDR_SIZE */
+
#endif
/* IFC */
+#ifndef SPL_NO_IFC
#if !defined(CONFIG_QSPI_BOOT) && !defined(CONFIG_SD_BOOT_QSPI)
#define CONFIG_FSL_IFC
/*
#define CONFIG_SYS_FLASH_BASE_PHYS CONFIG_SYS_FLASH_BASE
#define CONFIG_SYS_FLASH_BASE_PHYS_EARLY 0x00000000
-#ifndef CONFIG_SYS_NO_FLASH
+#ifdef CONFIG_MTD_NOR_FLASH
#define CONFIG_FLASH_CFI_DRIVER
#define CONFIG_SYS_FLASH_CFI
#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
#define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */
#endif
#endif
+#endif
/* I2C */
#define CONFIG_SYS_I2C
#define CONFIG_SYS_I2C_MXC_I2C4
/* PCIe */
+#ifndef SPL_NO_PCIE
#define CONFIG_PCIE1 /* PCIE controller 1 */
#define CONFIG_PCIE2 /* PCIE controller 2 */
#define CONFIG_PCIE3 /* PCIE controller 3 */
#ifdef CONFIG_PCI
#define CONFIG_NET_MULTI
#define CONFIG_PCI_SCAN_SHOW
-#define CONFIG_CMD_PCI
+#endif
#endif
/* Command line configuration */
-#define CONFIG_CMD_ENV
/* MMC */
+#ifndef SPL_NO_MMC
#ifdef CONFIG_MMC
#define CONFIG_FSL_ESDHC
#define CONFIG_SYS_FSL_MMC_HAS_CAPBLT_VS33
-#define CONFIG_GENERIC_MMC
-#define CONFIG_DOS_PARTITION
+#endif
#endif
/* DSPI */
+#ifndef SPL_NO_DSPI
#define CONFIG_FSL_DSPI
#ifdef CONFIG_FSL_DSPI
#define CONFIG_DM_SPI_FLASH
#define CONFIG_SF_DEFAULT_CS 0
#endif
#endif
-
-#define CONFIG_FSL_CAAM /* Enable SEC/CAAM */
+#endif
/* FMan ucode */
+#ifndef SPL_NO_FMAN
#define CONFIG_SYS_DPAA_FMAN
#ifdef CONFIG_SYS_DPAA_FMAN
#define CONFIG_SYS_FM_MURAM_SIZE 0x60000
#ifdef CONFIG_NAND_BOOT
-/* Store Fman ucode at offeset 0x160000(11 blocks). */
+/* Store Fman ucode at offeset 0x900000(72 blocks). */
#define CONFIG_SYS_QE_FMAN_FW_IN_NAND
-#define CONFIG_SYS_FMAN_FW_ADDR (11 * CONFIG_SYS_NAND_BLOCK_SIZE)
+#define CONFIG_SYS_FMAN_FW_ADDR (72 * CONFIG_SYS_NAND_BLOCK_SIZE)
#elif defined(CONFIG_SD_BOOT)
/*
* PBL SD boot image should stored at 0x1000(8 blocks), the size of the image is
* about 1MB (2040 blocks), Env is stored after the image, and the env size is
- * 0x2000 (16 blocks), 8 + 2040 + 16 = 2064, enlarge it to 2080(0x820).
+ * 0x2000 (16 blocks), 8 + 2040 + 16 = 2064, enlarge it to 18432(0x4800).
*/
#define CONFIG_SYS_QE_FMAN_FW_IN_MMC
-#define CONFIG_SYS_FMAN_FW_ADDR (512 * 0x820)
+#define CONFIG_SYS_FMAN_FW_ADDR (512 * 0x4800)
+#define CONFIG_SYS_QE_FW_ADDR (512 * 0x4a08)
#elif defined(CONFIG_QSPI_BOOT)
#define CONFIG_SYS_QE_FW_IN_SPIFLASH
-#define CONFIG_SYS_FMAN_FW_ADDR 0x400d0000
+#define CONFIG_SYS_FMAN_FW_ADDR 0x40900000
#define CONFIG_ENV_SPI_BUS 0
#define CONFIG_ENV_SPI_CS 0
#define CONFIG_ENV_SPI_MAX_HZ 1000000
#else
#define CONFIG_SYS_QE_FMAN_FW_IN_NOR
/* FMan fireware Pre-load address */
-#define CONFIG_SYS_FMAN_FW_ADDR 0x60300000
+#define CONFIG_SYS_FMAN_FW_ADDR 0x60900000
+#define CONFIG_SYS_QE_FW_ADDR 0x60940000
#endif
#define CONFIG_SYS_QE_FMAN_FW_LENGTH 0x10000
#define CONFIG_SYS_FDT_PAD (0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH)
#endif
+#endif
/* Miscellaneous configurable options */
#define CONFIG_SYS_LOAD_ADDR (CONFIG_SYS_DDR_SDRAM_BASE + 0x10000000)
#define CONFIG_HWCONFIG
#define HWCONFIG_BUFFER_SIZE 128
+#ifndef SPL_NO_MISC
#if defined(CONFIG_QSPI_BOOT) || defined(CONFIG_SD_BOOT_QSPI)
#define MTDPARTS_DEFAULT "mtdparts=spi0.0:1m(uboot)," \
"5m(kernel),1m(dtb),9m(file_system)"
#else
-#define MTDPARTS_DEFAULT "mtdparts=60000000.nor:1m(nor_bank0_rcw)," \
- "1m(nor_bank0_uboot),1m(nor_bank0_uboot_env)," \
- "1m(nor_bank0_fman_uconde),40m(nor_bank0_fit)," \
- "1m(nor_bank4_rcw),1m(nor_bank4_uboot)," \
- "1m(nor_bank4_uboot_env),1m(nor_bank4_fman_ucode)," \
- "40m(nor_bank4_fit);7e800000.flash:" \
+#define MTDPARTS_DEFAULT "mtdparts=60000000.nor:" \
+ "2m@0x100000(nor_bank0_uboot),"\
+ "40m@0x1100000(nor_bank0_fit)," \
+ "7m(nor_bank0_user)," \
+ "2m@0x4100000(nor_bank4_uboot)," \
+ "40m@0x5100000(nor_bank4_fit),"\
+ "-(nor_bank4_user);" \
+ "7e800000.flash:" \
"1m(nand_uboot),1m(nand_uboot_env)," \
"20m(nand_fit);spi0.0:1m(uboot)," \
"5m(kernel),1m(dtb),9m(file_system)"
#endif
+#include <config_distro_defaults.h>
+#ifndef CONFIG_SPL_BUILD
+#define BOOT_TARGET_DEVICES(func) \
+ func(MMC, mmc, 0) \
+ func(USB, usb, 0)
+#include <config_distro_bootcmd.h>
+#endif
+
/* Initial environment variables */
#define CONFIG_EXTRA_ENV_SETTINGS \
"hwconfig=fsl_ddr:bank_intlv=auto\0" \
- "loadaddr=0x80100000\0" \
"fdt_high=0xffffffffffffffff\0" \
"initrd_high=0xffffffffffffffff\0" \
- "kernel_start=0x61100000\0" \
- "kernel_load=0xa0000000\0" \
+ "fdt_addr=0x64f00000\0" \
+ "kernel_addr=0x65000000\0" \
+ "scriptaddr=0x80000000\0" \
+ "scripthdraddr=0x80080000\0" \
+ "fdtheader_addr_r=0x80100000\0" \
+ "kernelheader_addr_r=0x80200000\0" \
+ "kernel_addr_r=0x81000000\0" \
+ "fdt_addr_r=0x90000000\0" \
+ "load_addr=0xa0000000\0" \
"kernel_size=0x2800000\0" \
- "console=ttyS0,115200\0" \
- "mtdparts=" MTDPARTS_DEFAULT "\0"
-
-#define CONFIG_BOOTARGS "console=ttyS0,115200 root=/dev/ram0 " \
- "earlycon=uart8250,mmio,0x21c0500 " \
- MTDPARTS_DEFAULT
-
+ "console=ttyS0,115200\0" \
+ "mtdparts=" MTDPARTS_DEFAULT "\0" \
+ BOOTENV \
+ "boot_scripts=ls1043ardb_boot.scr\0" \
+ "boot_script_hdr=hdr_ls1043ardb_bs.out\0" \
+ "scan_dev_for_boot_part=" \
+ "part list ${devtype} ${devnum} devplist; " \
+ "env exists devplist || setenv devplist 1; " \
+ "for distro_bootpart in ${devplist}; do " \
+ "if fstype ${devtype} " \
+ "${devnum}:${distro_bootpart} " \
+ "bootfstype; then " \
+ "run scan_dev_for_boot; " \
+ "fi; " \
+ "done\0" \
+ "scan_dev_for_boot=" \
+ "echo Scanning ${devtype} " \
+ "${devnum}:${distro_bootpart}...; " \
+ "for prefix in ${boot_prefixes}; do " \
+ "run scan_dev_for_scripts; " \
+ "done;\0" \
+ "boot_a_script=" \
+ "load ${devtype} ${devnum}:${distro_bootpart} " \
+ "${scriptaddr} ${prefix}${script}; " \
+ "env exists secureboot && load ${devtype} " \
+ "${devnum}:${distro_bootpart} " \
+ "${scripthdraddr} ${prefix}${boot_script_hdr} " \
+ "&& esbc_validate ${scripthdraddr};" \
+ "source ${scriptaddr}\0" \
+ "installer=load mmc 0:2 $load_addr " \
+ "/flex_installer_arm64.itb; " \
+ "bootm $load_addr#ls1043ardb\0" \
+ "qspi_bootcmd=echo Trying load from qspi..;" \
+ "sf probe && sf read $load_addr " \
+ "$kernel_addr $kernel_size && bootm $load_addr#$board\0" \
+ "nor_bootcmd=echo Trying load from nor..;" \
+ "cp.b $kernel_addr $load_addr " \
+ "$kernel_size && bootm $load_addr#$board\0"
+
+#undef CONFIG_BOOTCOMMAND
#if defined(CONFIG_QSPI_BOOT) || defined(CONFIG_SD_BOOT_QSPI)
-#define CONFIG_BOOTCOMMAND "sf probe && sf read $kernel_load " \
- "e0000 f00000 && bootm $kernel_load"
+#define CONFIG_BOOTCOMMAND "run distro_bootcmd; env exists secureboot" \
+ "&& esbc_halt; run qspi_bootcmd;"
#else
-#define CONFIG_BOOTCOMMAND "cp.b $kernel_start $kernel_load " \
- "$kernel_size && bootm $kernel_load"
+#define CONFIG_BOOTCOMMAND "run distro_bootcmd; env exists secureboot" \
+ "&& esbc_halt; run nor_bootcmd;"
+#endif
#endif
/* Monitor Command Prompt */
#define CONFIG_SYS_CBSIZE 512 /* Console I/O Buffer Size */
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \
- sizeof(CONFIG_SYS_PROMPT) + 16)
-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot args buffer */
#define CONFIG_SYS_LONGHELP
+
+#ifndef SPL_NO_MISC
+#ifndef CONFIG_CMDLINE_EDITING
#define CONFIG_CMDLINE_EDITING 1
+#endif
+#endif
+
#define CONFIG_AUTO_COMPLETE
#define CONFIG_SYS_MAXARGS 64 /* max command args */
#define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */
-/* Hash command with SHA acceleration supported in hardware */
-#ifdef CONFIG_FSL_CAAM
-#define CONFIG_CMD_HASH
-#define CONFIG_SHA_HW_ACCEL
-#endif
+#include <asm/arch/soc.h>
#endif /* __LS1043A_COMMON_H */