/* SPDX-License-Identifier: GPL-2.0+ */
/*
- * Copyright 2019 NXP
+ * Copyright 2019, 2021 NXP
*/
#ifndef __LS1028A_RDB_H
#include "ls1028a_common.h"
-#define CONFIG_SYS_CLK_FREQ 100000000
-#define CONFIG_DDR_CLK_FREQ 100000000
-#define COUNTER_FREQUENCY_REAL (CONFIG_SYS_CLK_FREQ / 4)
+#define COUNTER_FREQUENCY_REAL (get_board_sys_clk() / 4)
-#define CONFIG_SYS_RTC_BUS_NUM 0
+#define CFG_SYS_RTC_BUS_NUM 0
/* Store environment at top of flash */
-#define CONFIG_DIMM_SLOTS_PER_CTLR 1
-
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
-
-#define CONFIG_QIXIS_I2C_ACCESS
-
/*
* QIXIS Definitions
*/
-#define CONFIG_FSL_QIXIS
#ifdef CONFIG_FSL_QIXIS
#define QIXIS_BASE 0x7fb00000
#define QIXIS_BASE_PHYS QIXIS_BASE
-#define CONFIG_SYS_I2C_FPGA_ADDR 0x66
+#define CFG_SYS_I2C_FPGA_ADDR 0x66
#define QIXIS_LBMAP_SWITCH 2
#define QIXIS_LBMAP_MASK 0xe0
#define QIXIS_LBMAP_SHIFT 0x5
#define QIXIS_LBMAP_ALTBANK 0x00
#define QIXIS_LBMAP_SD 0x00
#define QIXIS_LBMAP_EMMC 0x00
-#define QIXIS_LBMAP_QSPI 0x00
+#define QIXIS_LBMAP_XSPI 0x00
#define QIXIS_RCW_SRC_SD 0xf8
#define QIXIS_RCW_SRC_EMMC 0xf9
-#define QIXIS_RCW_SRC_QSPI 0xff
+#define QIXIS_RCW_SRC_XSPI 0xff
#define QIXIS_RST_CTL_RESET 0x31
#define QIXIS_RCFG_CTL_RECONFIG_IDLE 0x10
#define QIXIS_RCFG_CTL_RECONFIG_START 0x11
#define QIXIS_RCFG_CTL_WATCHDOG_ENBLE 0x08
#define QIXIS_RST_FORCE_MEM 0x01
-#define CONFIG_SYS_FPGA_CSPR_EXT (0x0)
-#define CONFIG_SYS_FPGA_CSPR (CSPR_PHYS_ADDR(QIXIS_BASE_PHYS) | \
+#define CFG_SYS_FPGA_CSPR_EXT (0x0)
+#define CFG_SYS_FPGA_CSPR (CSPR_PHYS_ADDR(QIXIS_BASE_PHYS) | \
CSPR_PORT_SIZE_8 | \
CSPR_MSEL_GPCM | \
CSPR_V)
-#define CONFIG_SYS_FPGA_CSOR (CSOR_NOR_ADM_SHIFT(4) | \
+#define CFG_SYS_FPGA_CSOR (CSOR_NOR_ADM_SHIFT(4) | \
CSOR_NOR_NOR_MODE_AVD_NOR | \
CSOR_NOR_TRHZ_80)
#endif
/* SATA */
-#ifndef CONFIG_CMD_EXT2
-#define CONFIG_CMD_EXT2
-#endif
-#define CONFIG_SYS_SCSI_MAX_SCSI_ID 1
-#define CONFIG_SYS_SCSI_MAX_LUN 1
-#define CONFIG_SYS_SCSI_MAX_DEVICE (CONFIG_SYS_SCSI_MAX_SCSI_ID * \
- CONFIG_SYS_SCSI_MAX_LUN)
#define SCSI_VEND_ID 0x1b4b
#define SCSI_DEV_ID 0x9170
#define CONFIG_SCSI_DEV_LIST {SCSI_VEND_ID, SCSI_DEV_ID}
-#define CONFIG_SCSI_AHCI_PLAT
-#define CONFIG_SYS_SATA1 AHCI_BASE_ADDR1
+/* Initial environment variables */
+#ifndef SPL_NO_ENV
+#undef CONFIG_EXTRA_ENV_SETTINGS
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "board=ls1028ardb\0" \
+ "hwconfig=fsl_ddr:bank_intlv=auto\0" \
+ "ramdisk_addr=0x800000\0" \
+ "ramdisk_size=0x2000000\0" \
+ "bootm_size=0x10000000\0" \
+ "kernel_addr=0x01000000\0" \
+ "scriptaddr=0x80000000\0" \
+ "scripthdraddr=0x80080000\0" \
+ "fdtheader_addr_r=0x80100000\0" \
+ "kernelheader_addr_r=0x80200000\0" \
+ "load_addr=0xa0000000\0" \
+ "kernel_addr_r=0x81000000\0" \
+ "fdt_addr_r=0x90000000\0" \
+ "ramdisk_addr_r=0xa0000000\0" \
+ "kernel_start=0x1000000\0" \
+ "kernelheader_start=0x600000\0" \
+ "kernel_load=0xa0000000\0" \
+ "kernel_size=0x2800000\0" \
+ "kernelheader_size=0x40000\0" \
+ "kernel_addr_sd=0x8000\0" \
+ "kernel_size_sd=0x14000\0" \
+ "kernelhdr_addr_sd=0x3000\0" \
+ "kernelhdr_size_sd=0x20\0" \
+ "console=ttyS0,115200\0" \
+ BOOTENV \
+ "boot_scripts=ls1028ardb_boot.scr\0" \
+ "boot_script_hdr=hdr_ls1028ardb_bs.out\0" \
+ "scan_dev_for_boot_part=" \
+ "part list ${devtype} ${devnum} devplist; " \
+ "env exists devplist || setenv devplist 1; " \
+ "for distro_bootpart in ${devplist}; do " \
+ "if fstype ${devtype} " \
+ "${devnum}:${distro_bootpart} " \
+ "bootfstype; then " \
+ "run scan_dev_for_boot; " \
+ "fi; " \
+ "done\0" \
+ "boot_a_script=" \
+ "load ${devtype} ${devnum}:${distro_bootpart} " \
+ "${scriptaddr} ${prefix}${script}; " \
+ "env exists secureboot && load ${devtype} " \
+ "${devnum}:${distro_bootpart} " \
+ "${scripthdraddr} ${prefix}${boot_script_hdr} " \
+ "&& esbc_validate ${scripthdraddr};" \
+ "source ${scriptaddr}\0" \
+ "xspi_bootcmd=echo Trying load from FlexSPI flash ...;" \
+ "sf probe 0:0 && sf read $load_addr " \
+ "$kernel_start $kernel_size ; env exists secureboot &&" \
+ "sf read $kernelheader_addr_r $kernelheader_start " \
+ "$kernelheader_size && esbc_validate ${kernelheader_addr_r}; "\
+ " bootm $load_addr#$board\0" \
+ "xspi_hdploadcmd=echo Trying load HDP firmware from FlexSPI...;" \
+ "sf probe 0:0 && sf read $load_addr 0x940000 0x30000 " \
+ "&& hdp load $load_addr 0x2000\0" \
+ "sd_bootcmd=echo Trying load from SD ...;" \
+ "mmc dev 0;mmcinfo; mmc read $load_addr " \
+ "$kernel_addr_sd $kernel_size_sd && " \
+ "env exists secureboot && mmc read $kernelheader_addr_r " \
+ "$kernelhdr_addr_sd $kernelhdr_size_sd " \
+ " && esbc_validate ${kernelheader_addr_r};" \
+ "bootm $load_addr#$board\0" \
+ "sd_hdploadcmd=echo Trying load HDP firmware from SD..;" \
+ "mmc dev 0;mmcinfo;mmc read $load_addr 0x4a00 0x200 " \
+ "&& hdp load $load_addr 0x2000\0" \
+ "emmc_bootcmd=echo Trying load from EMMC ..;" \
+ "mmc dev 1;mmcinfo; mmc read $load_addr " \
+ "$kernel_addr_sd $kernel_size_sd && " \
+ "env exists secureboot && mmc read $kernelheader_addr_r " \
+ "$kernelhdr_addr_sd $kernelhdr_size_sd " \
+ " && esbc_validate ${kernelheader_addr_r};" \
+ "bootm $load_addr#$board\0" \
+ "emmc_hdploadcmd=echo Trying load HDP firmware from EMMC..;" \
+ "mmc dev 1;mmcinfo;mmc read $load_addr 0x4a00 0x200 " \
+ "&& hdp load $load_addr 0x2000\0"
+#endif
#endif /* __LS1028A_RDB_H */
projects / platform / kernel / u-boot.git / blobdiff