Convert CONFIG_PCI_GT64120 to Kconfig

[platform/kernel/u-boot.git] / include / configs / ls1028a_common.h

diff --git a/include/configs/ls1028a_common.h b/include/configs/ls1028a_common.h
index d184673..5b0b86b 100644 (file)
--- a/include/configs/ls1028a_common.h
+++ b/include/configs/ls1028a_common.h
@@ -1,23 +1,16 @@
 /* SPDX-License-Identifier: GPL-2.0+ */
 /*
- * Copyright 2019-2020 NXP
+ * Copyright 2019-2021 NXP
  */
 
 #ifndef __L1028A_COMMON_H
 #define __L1028A_COMMON_H
 
-#define CONFIG_REMAKE_ELF
-#define CONFIG_FSL_LAYERSCAPE
-#define CONFIG_MP
-
 #include <asm/arch/stream_id_lsch3.h>
 #include <asm/arch/config.h>
 #include <asm/arch/soc.h>
 
 /* Link Definitions */
-#define CONFIG_SYS_INIT_SP_ADDR                CONFIG_SYS_TEXT_BASE
-
-#define CONFIG_SKIP_LOWLEVEL_INIT
 
 #define CONFIG_VERY_BIG_RAM
 #define CONFIG_SYS_DDR_SDRAM_BASE      0x80000000UL
@@ -29,38 +22,24 @@
 /*
  * SMP Definitinos
  */
-#define CPU_RELEASE_ADDR               secondary_boot_func
+#define CPU_RELEASE_ADDR               secondary_boot_addr
 
-/* Generic Timer Definitions */
-#define COUNTER_FREQUENCY              25000000        /* 25MHz */
-
-/* Size of malloc() pool */
-#define CONFIG_SYS_MALLOC_LEN          (CONFIG_ENV_SIZE + 2048 * 1024)
+/* GPIO */
 
 /* I2C */
-#ifndef CONFIG_DM_I2C
-#define CONFIG_SYS_I2C
-#endif
 
 /* Serial Port */
 #define CONFIG_SYS_NS16550_SERIAL
 #define CONFIG_SYS_NS16550_REG_SIZE     1
 #define CONFIG_SYS_NS16550_CLK          (get_bus_freq(0) / 2)
 
-#define CONFIG_SYS_BAUDRATE_TABLE      { 9600, 19200, 38400, 57600, 115200 }
-
 /* Miscellaneous configurable options */
-#define CONFIG_SYS_LOAD_ADDR   (CONFIG_SYS_DDR_SDRAM_BASE + 0x10000000)
 
 /* Physical Memory Map */
-#define CONFIG_CHIP_SELECTS_PER_CTRL   4
 
 #define CONFIG_HWCONFIG
 #define HWCONFIG_BUFFER_SIZE           128
 
-/* Allow to overwrite serial and ethaddr */
-#define CONFIG_ENV_OVERWRITE
-
 #define BOOT_TARGET_DEVICES(func) \
        func(MMC, mmc, 0) \
        func(MMC, mmc, 1) \
@@ -68,8 +47,6 @@
        func(DHCP, dhcp, na)
 #include <config_distro_bootcmd.h>
 
-#undef CONFIG_BOOTCOMMAND
-
 #define XSPI_NOR_BOOTCOMMAND   \
        "run xspi_hdploadcmd; run distro_bootcmd; run xspi_bootcmd; " \
        "env exists secureboot && esbc_halt;;"
@@ -80,39 +57,18 @@
        "run emmc_hdploadcmd; run distro_bootcmd;run emmc_bootcmd; " \
        "env exists secureboot && esbc_halt;"
 
-/* Monitor Command Prompt */
-#define CONFIG_SYS_CBSIZE              512     /* Console I/O Buffer Size */
-#define CONFIG_SYS_PBSIZE              (CONFIG_SYS_CBSIZE + \
-                                       sizeof(CONFIG_SYS_PROMPT) + 16)
-#define CONFIG_SYS_BARGSIZE            CONFIG_SYS_CBSIZE /* Boot args buffer */
-
-#define CONFIG_SYS_MAXARGS             64      /* max command args */
-
 #define CONFIG_SYS_BOOTM_LEN   (64 << 20)      /* Increase max gunzip size */
 
-/*  MMC  */
-#ifdef CONFIG_MMC
-#define CONFIG_SYS_FSL_MMC_HAS_CAPBLT_VS33
-#endif
-
-#define CONFIG_SYS_MMC_ENV_DEV         0
 #define OCRAM_NONSECURE_SIZE           0x00010000
 #define CONFIG_SYS_FSL_QSPI_BASE       0x20000000
 
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
-
 /* I2C bus multiplexer */
 #define I2C_MUX_PCA_ADDR_PRI            0x77 /* Primary Mux*/
 #define I2C_MUX_CH_DEFAULT              0x8
 
 /* EEPROM */
-#define CONFIG_ID_EEPROM
 #define CONFIG_SYS_I2C_EEPROM_NXID
 #define CONFIG_SYS_EEPROM_BUS_NUM              0
-#define CONFIG_SYS_I2C_EEPROM_ADDR             0x57
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN         1
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS      3
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS  5
 
 /* DisplayPort */
 #define DP_PWD_EN_DEFAULT_MASK          0x8
@@ -121,8 +77,4 @@
 #include <asm/fsl_secure_boot.h>
 #endif
 
-/* Ethernet */
-/* smallest ENETC BD ring has 8 entries */
-#define CONFIG_SYS_RX_ETH_BUFFER               8
-
 #endif /* __L1028A_COMMON_H */