+/* SPDX-License-Identifier: GPL-2.0+ */
/*
* Copyright 2014 Freescale Semiconductor, Inc.
- *
- * SPDX-License-Identifier: GPL-2.0+
*/
#ifndef __CONFIG_H
#define CONFIG_SYS_INIT_RAM_ADDR OCRAM_BASE_ADDR
#define CONFIG_SYS_INIT_RAM_SIZE OCRAM_SIZE
-/*
- * USB
- */
-
-/*
- * EHCI Support - disbaled by default as
- * there is no signal coming out of soc on
- * this board for this controller. However,
- * the silicon still has this controller,
- * and anyone can use this controller by
- * taking signals out on their board.
- */
-
-/*#define CONFIG_HAS_FSL_DR_USB*/
-
-#ifdef CONFIG_HAS_FSL_DR_USB
-#define CONFIG_USB_EHCI_FSL
-#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
-#endif
-
-/* XHCI Support - enabled by default */
-#define CONFIG_HAS_FSL_XHCI_USB
-
-#ifdef CONFIG_HAS_FSL_XHCI_USB
-#define CONFIG_USB_XHCI_FSL
-#define CONFIG_USB_MAX_CONTROLLER_COUNT 1
-#endif
-
#define CONFIG_SYS_CLK_FREQ 100000000
#define CONFIG_DDR_CLK_FREQ 100000000
#define CONFIG_SYS_FSL_PBL_RCW \
board/freescale/ls1021atwr/ls102xa_rcw_sd_ifc.cfg
#endif
-#define CONFIG_SPL_FRAMEWORK
-#define CONFIG_SPL_LDSCRIPT "arch/$(ARCH)/cpu/u-boot-spl.lds"
#ifdef CONFIG_SECURE_BOOT
/*
#define CONFIG_U_BOOT_HDR_SIZE (16 << 10)
#endif /* ifdef CONFIG_SECURE_BOOT */
-#define CONFIG_SPL_TEXT_BASE 0x10000000
#define CONFIG_SPL_MAX_SIZE 0x1a000
#define CONFIG_SPL_STACK 0x1001d000
#define CONFIG_SPL_PAD_TO 0x1c000
-#define CONFIG_SYS_TEXT_BASE 0x82000000
#define CONFIG_SYS_SPL_MALLOC_START (CONFIG_SYS_TEXT_BASE + \
CONFIG_SYS_MONITOR_LEN)
#endif /* ifdef CONFIG_U_BOOT_HDR_SIZE */
#endif
-#ifdef CONFIG_QSPI_BOOT
-#define CONFIG_SYS_TEXT_BASE 0x40100000
-#endif
-
-#ifndef CONFIG_SYS_TEXT_BASE
-#define CONFIG_SYS_TEXT_BASE 0x60100000
-#endif
-
-#define CONFIG_NR_DRAM_BANKS 1
#define PHYS_SDRAM 0x80000000
#define PHYS_SDRAM_SIZE (1u * 1024 * 1024 * 1024)
#define CONFIG_SYS_DDR_SDRAM_BASE 0x80000000UL
#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE
+#define CONFIG_CHIP_SELECTS_PER_CTRL 4
+
#if !defined(CONFIG_SD_BOOT) && !defined(CONFIG_NAND_BOOT) && \
!defined(CONFIG_QSPI_BOOT)
-#define CONFIG_U_QE
#define CONFIG_SYS_QE_FMAN_FW_IN_NOR
#endif
FTIM2_NOR_TWPH(0x0e))
#define CONFIG_SYS_NOR_FTIM3 0
-#define CONFIG_FLASH_CFI_DRIVER
-#define CONFIG_SYS_FLASH_CFI
-#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
#define CONFIG_SYS_FLASH_QUIET_TEST
#define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */
#ifdef CONFIG_LPUART
#define CONFIG_LPUART_32B_REG
#else
-#define CONFIG_CONS_INDEX 1
#define CONFIG_SYS_NS16550_SERIAL
#ifndef CONFIG_DM_SERIAL
#define CONFIG_SYS_NS16550_REG_SIZE 1
/*
* MMC
*/
-#define CONFIG_FSL_ESDHC
/* SPI */
#if defined(CONFIG_QSPI_BOOT) || defined(CONFIG_SD_BOOT_QSPI)
/*
* eTSEC
*/
-#define CONFIG_TSEC_ENET
#ifdef CONFIG_TSEC_ENET
-#define CONFIG_MII
#define CONFIG_MII_DEFAULT_TSEC 1
#define CONFIG_TSEC1 1
#define CONFIG_TSEC1_NAME "eTSEC1"
#define CONFIG_ETHPRIME "eTSEC1"
-#define CONFIG_PHY_GIGE
-#define CONFIG_PHYLIB
#define CONFIG_PHY_ATHEROS
#define CONFIG_HAS_ETH0
#ifdef CONFIG_PCI
#define CONFIG_PCI_SCAN_SHOW
-#define CONFIG_CMD_PCI
#endif
#define CONFIG_CMDLINE_TAG
-#define CONFIG_CMDLINE_EDITING
#define CONFIG_PEN_ADDR_BIG_ENDIAN
#define CONFIG_LAYERSCAPE_NS_ACCESS
#define CONFIG_FSL_DEVICE_DISABLE
+#define BOOT_TARGET_DEVICES(func) \
+ func(MMC, mmc, 0) \
+ func(USB, usb, 0) \
+ func(DHCP, dhcp, na)
+#include <config_distro_bootcmd.h>
#ifdef CONFIG_LPUART
#define CONFIG_EXTRA_ENV_SETTINGS \
"bootargs=root=/dev/ram0 rw console=ttyLP0,115200\0" \
"initrd_high=0xffffffff\0" \
- "fdt_high=0xffffffff\0"
+ "fdt_high=0xffffffff\0" \
+ "fdt_addr=0x64f00000\0" \
+ "kernel_addr=0x65000000\0" \
+ "scriptaddr=0x80000000\0" \
+ "scripthdraddr=0x80080000\0" \
+ "fdtheader_addr_r=0x80100000\0" \
+ "kernelheader_addr_r=0x80200000\0" \
+ "kernel_addr_r=0x81000000\0" \
+ "fdt_addr_r=0x90000000\0" \
+ "ramdisk_addr_r=0xa0000000\0" \
+ "load_addr=0xa0000000\0" \
+ "kernel_size=0x2800000\0" \
+ "kernel_addr_sd=0x8000\0" \
+ "kernel_size_sd=0x14000\0" \
+ BOOTENV \
+ "boot_scripts=ls1021atwr_boot.scr\0" \
+ "boot_script_hdr=hdr_ls1021atwr_bs.out\0" \
+ "scan_dev_for_boot_part=" \
+ "part list ${devtype} ${devnum} devplist; " \
+ "env exists devplist || setenv devplist 1; " \
+ "for distro_bootpart in ${devplist}; do " \
+ "if fstype ${devtype} " \
+ "${devnum}:${distro_bootpart} " \
+ "bootfstype; then " \
+ "run scan_dev_for_boot; " \
+ "fi; " \
+ "done\0" \
+ "scan_dev_for_boot=" \
+ "echo Scanning ${devtype} " \
+ "${devnum}:${distro_bootpart}...; " \
+ "for prefix in ${boot_prefixes}; do " \
+ "run scan_dev_for_scripts; " \
+ "done;" \
+ "\0" \
+ "boot_a_script=" \
+ "load ${devtype} ${devnum}:${distro_bootpart} " \
+ "${scriptaddr} ${prefix}${script}; " \
+ "env exists secureboot && load ${devtype} " \
+ "${devnum}:${distro_bootpart} " \
+ "${scripthdraddr} ${prefix}${boot_script_hdr}; " \
+ "env exists secureboot " \
+ "&& esbc_validate ${scripthdraddr};" \
+ "source ${scriptaddr}\0" \
+ "installer=load mmc 0:2 $load_addr " \
+ "/flex_installer_arm32.itb; " \
+ "bootm $load_addr#ls1021atwr\0" \
+ "qspi_bootcmd=echo Trying load from qspi..;" \
+ "sf probe && sf read $load_addr " \
+ "$kernel_addr $kernel_size && bootm $load_addr#$board\0" \
+ "nor_bootcmd=echo Trying load from nor..;" \
+ "cp.b $kernel_addr $load_addr " \
+ "$kernel_size && bootm $load_addr#$board\0"
#else
#define CONFIG_EXTRA_ENV_SETTINGS \
"bootargs=root=/dev/ram0 rw console=ttyS0,115200\0" \
"initrd_high=0xffffffff\0" \
- "fdt_high=0xffffffff\0"
+ "fdt_high=0xffffffff\0" \
+ "fdt_addr=0x64f00000\0" \
+ "kernel_addr=0x61000000\0" \
+ "kernelheader_addr=0x60800000\0" \
+ "scriptaddr=0x80000000\0" \
+ "scripthdraddr=0x80080000\0" \
+ "fdtheader_addr_r=0x80100000\0" \
+ "kernelheader_addr_r=0x80200000\0" \
+ "kernel_addr_r=0x81000000\0" \
+ "kernelheader_size=0x40000\0" \
+ "fdt_addr_r=0x90000000\0" \
+ "ramdisk_addr_r=0xa0000000\0" \
+ "load_addr=0xa0000000\0" \
+ "kernel_size=0x2800000\0" \
+ "kernel_addr_sd=0x8000\0" \
+ "kernel_size_sd=0x14000\0" \
+ "kernelhdr_addr_sd=0x4000\0" \
+ "kernelhdr_size_sd=0x10\0" \
+ BOOTENV \
+ "boot_scripts=ls1021atwr_boot.scr\0" \
+ "boot_script_hdr=hdr_ls1021atwr_bs.out\0" \
+ "scan_dev_for_boot_part=" \
+ "part list ${devtype} ${devnum} devplist; " \
+ "env exists devplist || setenv devplist 1; " \
+ "for distro_bootpart in ${devplist}; do " \
+ "if fstype ${devtype} " \
+ "${devnum}:${distro_bootpart} " \
+ "bootfstype; then " \
+ "run scan_dev_for_boot; " \
+ "fi; " \
+ "done\0" \
+ "scan_dev_for_boot=" \
+ "echo Scanning ${devtype} " \
+ "${devnum}:${distro_bootpart}...; " \
+ "for prefix in ${boot_prefixes}; do " \
+ "run scan_dev_for_scripts; " \
+ "done;" \
+ "\0" \
+ "boot_a_script=" \
+ "load ${devtype} ${devnum}:${distro_bootpart} " \
+ "${scriptaddr} ${prefix}${script}; " \
+ "env exists secureboot && load ${devtype} " \
+ "${devnum}:${distro_bootpart} " \
+ "${scripthdraddr} ${prefix}${boot_script_hdr} " \
+ "&& esbc_validate ${scripthdraddr};" \
+ "source ${scriptaddr}\0" \
+ "qspi_bootcmd=echo Trying load from qspi..;" \
+ "sf probe && sf read $load_addr " \
+ "$kernel_addr $kernel_size; env exists secureboot " \
+ "&& sf read $kernelheader_addr_r $kernelheader_addr " \
+ "$kernelheader_size && esbc_validate ${kernelheader_addr_r}; " \
+ "bootm $load_addr#$board\0" \
+ "nor_bootcmd=echo Trying load from nor..;" \
+ "cp.b $kernel_addr $load_addr " \
+ "$kernel_size; env exists secureboot " \
+ "&& cp.b $kernelheader_addr $kernelheader_addr_r " \
+ "$kernelheader_size && esbc_validate ${kernelheader_addr_r}; " \
+ "bootm $load_addr#$board\0" \
+ "sd_bootcmd=echo Trying load from SD ..;" \
+ "mmcinfo && mmc read $load_addr " \
+ "$kernel_addr_sd $kernel_size_sd && " \
+ "env exists secureboot && mmc read $kernelheader_addr_r " \
+ "$kernelhdr_addr_sd $kernelhdr_size_sd " \
+ " && esbc_validate ${kernelheader_addr_r};" \
+ "bootm $load_addr#$board\0"
+#endif
+
+#undef CONFIG_BOOTCOMMAND
+#if defined(CONFIG_QSPI_BOOT) || defined(CONFIG_SD_BOOT_QSPI)
+#define CONFIG_BOOTCOMMAND "run distro_bootcmd; run qspi_bootcmd" \
+ "env exists secureboot && esbc_halt"
+#elif defined(CONFIG_SD_BOOT)
+#define CONFIG_BOOTCOMMAND "run distro_bootcmd; run sd_bootcmd; " \
+ "env exists secureboot && esbc_halt;"
+#else
+#define CONFIG_BOOTCOMMAND "run distro_bootcmd; run nor_bootcmd;" \
+ "env exists secureboot && esbc_halt;"
#endif
/*
* Miscellaneous configurable options
*/
-#define CONFIG_SYS_LONGHELP /* undef to save memory */
-#define CONFIG_AUTO_COMPLETE
-#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
-#define CONFIG_SYS_PBSIZE \
- (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
-#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
#define CONFIG_SYS_MEMTEST_START 0x80000000
#define CONFIG_SYS_MEMTEST_END 0x9fffffff
#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K (one sector) */
#endif
-#define CONFIG_MISC_INIT_R
-
#include <asm/fsl_secure_boot.h>
#define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */