global: Migrate CONFIG_MXC_UART_BASE to CFG

[platform/kernel/u-boot.git] / include / configs / ls1021atsn.h

diff --git a/include/configs/ls1021atsn.h b/include/configs/ls1021atsn.h
index 905c63d..b722586 100644 (file)
--- a/include/configs/ls1021atsn.h
+++ b/include/configs/ls1021atsn.h
@@ -6,11 +6,10 @@
 #ifndef __CONFIG_H
 #define __CONFIG_H
 
-#define CONFIG_SYS_INIT_RAM_ADDR       OCRAM_BASE_ADDR
-#define CONFIG_SYS_INIT_RAM_SIZE       OCRAM_SIZE
+#define CFG_SYS_INIT_RAM_ADDR  OCRAM_BASE_ADDR
+#define CFG_SYS_INIT_RAM_SIZE  OCRAM_SIZE
 
 /* XHCI Support - enabled by default */
-#define CONFIG_USB_MAX_CONTROLLER_COUNT        1
 
 #define DDR_SDRAM_CFG                  0x470c0008
 #define DDR_CS0_BNDS                   0x008000bf
@@ -39,69 +38,29 @@
 #define SDRAM_CFG2_FRC_SR              0x80000000
 #define SDRAM_CFG_BI                   0x00000001
 
-#ifdef CONFIG_SD_BOOT
-#ifdef CONFIG_NXP_ESBC
-#define CONFIG_U_BOOT_HDR_SIZE         (16 << 10)
-#endif /* ifdef CONFIG_NXP_ESBC */
-
-#ifdef CONFIG_U_BOOT_HDR_SIZE
-/*
- * HDR would be appended at end of image and copied to DDR along
- * with U-Boot image. Here u-boot max. size is 512K. So if binary
- * size increases then increase this size in case of secure boot as
- * it uses raw U-Boot image instead of FIT image.
- */
-#define CONFIG_SYS_MONITOR_LEN         (0x100000 + CONFIG_U_BOOT_HDR_SIZE)
-#else
-#define CONFIG_SYS_MONITOR_LEN         0x100000
-#endif /* ifdef CONFIG_U_BOOT_HDR_SIZE */
-#endif
-
 #define PHYS_SDRAM                     0x80000000
 #define PHYS_SDRAM_SIZE                        (1u * 1024 * 1024 * 1024)
 
-#define CONFIG_SYS_DDR_SDRAM_BASE      0x80000000UL
-#define CONFIG_SYS_SDRAM_BASE          CONFIG_SYS_DDR_SDRAM_BASE
+#define CFG_SYS_DDR_SDRAM_BASE 0x80000000UL
+#define CFG_SYS_SDRAM_BASE             CFG_SYS_DDR_SDRAM_BASE
 
 /* Serial Port */
-#define CONFIG_SYS_NS16550_SERIAL
-#ifndef CONFIG_DM_SERIAL
-#define CONFIG_SYS_NS16550_REG_SIZE    1
-#endif
-#define CONFIG_SYS_NS16550_CLK         get_serial_clock()
+#define CFG_SYS_NS16550_CLK            get_serial_clock()
 
 /* I2C */
 
-/* EEPROM */
-#define CONFIG_SYS_I2C_EEPROM_NXID
-#define CONFIG_SYS_EEPROM_BUS_NUM      0
-
-/* QSPI */
-#define FSL_QSPI_FLASH_SIZE            (1 << 24)
-#define FSL_QSPI_FLASH_NUM             2
-
 /* PCIe */
-#define CONFIG_PCIE1                   /* PCIE controller 1 */
-#define CONFIG_PCIE2                   /* PCIE controller 2 */
 #define FSL_PCIE_COMPAT                        "fsl,ls1021a-pcie"
-#ifdef CONFIG_PCI
-#define CONFIG_PCI_SCAN_SHOW
-#endif
-
-#define CONFIG_LAYERSCAPE_NS_ACCESS
 
-#define CONFIG_HWCONFIG
 #define HWCONFIG_BUFFER_SIZE           256
 
-#define CONFIG_FSL_DEVICE_DISABLE
-
 #define BOOT_TARGET_DEVICES(func) \
        func(MMC, mmc, 0) \
        func(USB, usb, 0) \
        func(DHCP, dhcp, na)
 #include <config_distro_bootcmd.h>
 
-#define CONFIG_EXTRA_ENV_SETTINGS                                      \
+#define CFG_EXTRA_ENV_SETTINGS                                 \
        "bootargs=root=/dev/ram0 rw console=ttyS0,115200\0"             \
        "initrd_high=0xffffffff\0"                                      \
        "kernel_addr=0x61000000\0"                                      \
@@ -164,12 +123,8 @@
                "bootm $load_addr#$board\0"
 
 /* Miscellaneous configurable options */
-#define CONFIG_SYS_BOOTMAPSZ           (256 << 20)
-
-#define CONFIG_LS102XA_STREAM_ID
+#define CFG_SYS_BOOTMAPSZ              (256 << 20)
 
 /* Environment */
 
-#define CONFIG_SYS_BOOTM_LEN           0x8000000 /* 128 MB */
-
 #endif