arm: Disable ATAGs support

[platform/kernel/u-boot.git] / include / configs / ls1021aqds.h

diff --git a/include/configs/ls1021aqds.h b/include/configs/ls1021aqds.h
index 7f65845..a164796 100644 (file)
--- a/include/configs/ls1021aqds.h
+++ b/include/configs/ls1021aqds.h
@@ -11,45 +11,23 @@
 
 #define CONFIG_SYS_FSL_CLK
 
-#define CONFIG_SKIP_LOWLEVEL_INIT
-
 #define CONFIG_DEEP_SLEEP
 
-/*
- * Size of malloc() pool
- */
-#define CONFIG_SYS_MALLOC_LEN          (CONFIG_ENV_SIZE + 16 * 1024 * 1024)
-
 #define CONFIG_SYS_INIT_RAM_ADDR       OCRAM_BASE_ADDR
 #define CONFIG_SYS_INIT_RAM_SIZE       OCRAM_SIZE
 
 #ifndef __ASSEMBLY__
 unsigned long get_board_sys_clk(void);
-unsigned long get_board_ddr_clk(void);
 #endif
 
 #if defined(CONFIG_QSPI_BOOT) || defined(CONFIG_SD_BOOT_QSPI)
 #define CONFIG_SYS_CLK_FREQ            100000000
-#define CONFIG_DDR_CLK_FREQ            100000000
 #define CONFIG_QIXIS_I2C_ACCESS
 #else
 #define CONFIG_SYS_CLK_FREQ            get_board_sys_clk()
-#define CONFIG_DDR_CLK_FREQ            get_board_ddr_clk()
-#endif
-
-#ifdef CONFIG_RAMBOOT_PBL
-#define CONFIG_SYS_FSL_PBL_PBI board/freescale/ls1021aqds/ls102xa_pbi.cfg
 #endif
 
 #ifdef CONFIG_SD_BOOT
-#ifdef CONFIG_SD_BOOT_QSPI
-#define CONFIG_SYS_FSL_PBL_RCW \
-       board/freescale/ls1021aqds/ls102xa_rcw_sd_qspi.cfg
-#else
-#define CONFIG_SYS_FSL_PBL_RCW \
-       board/freescale/ls1021aqds/ls102xa_rcw_sd_ifc.cfg
-#endif
-
 #define CONFIG_SPL_MAX_SIZE            0x1a000
 #define CONFIG_SPL_STACK               0x1001d000
 #define CONFIG_SPL_PAD_TO              0x1c000
@@ -63,8 +41,6 @@ unsigned long get_board_ddr_clk(void);
 #endif
 
 #ifdef CONFIG_NAND_BOOT
-#define CONFIG_SYS_FSL_PBL_RCW board/freescale/ls1021aqds/ls102xa_rcw_nand.cfg
-
 #define CONFIG_SPL_MAX_SIZE            0x1a000
 #define CONFIG_SPL_STACK               0x1001d000
 #define CONFIG_SPL_PAD_TO              0x1c000
@@ -82,7 +58,6 @@ unsigned long get_board_ddr_clk(void);
 #define CONFIG_SYS_MONITOR_LEN         0x80000
 #endif
 
-#define CONFIG_DDR_SPD
 #define SPD_EEPROM_ADDRESS             0x51
 #define CONFIG_SYS_SPD_BUS_NUM         0
 
@@ -95,9 +70,7 @@ unsigned long get_board_ddr_clk(void);
 #define CONFIG_SYS_DDR_SDRAM_BASE      0x80000000UL
 #define CONFIG_SYS_SDRAM_BASE          CONFIG_SYS_DDR_SDRAM_BASE
 
-#define CONFIG_DDR_ECC
 #ifdef CONFIG_DDR_ECC
-#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER
 #define CONFIG_MEM_INIT_VALUE           0xdeadbeef
 #endif
 
@@ -330,16 +303,6 @@ unsigned long get_board_ddr_clk(void);
 /*
  * I2C
  */
-#if !CONFIG_IS_ENABLED(DM_I2C)
-#define CONFIG_SYS_I2C
-#else
-#define CONFIG_I2C_SET_DEFAULT_BUS_NUM
-#define CONFIG_I2C_DEFAULT_BUS_NUMBER 0
-#endif
-#define CONFIG_SYS_I2C_MXC
-#define CONFIG_SYS_I2C_MXC_I2C1                /* enable I2C bus 1 */
-#define CONFIG_SYS_I2C_MXC_I2C2                /* enable I2C bus 2 */
-#define CONFIG_SYS_I2C_MXC_I2C3                /* enable I2C bus 3 */
 
 /* GPIO */
 #ifdef CONFIG_DM_GPIO
@@ -349,13 +312,8 @@ unsigned long get_board_ddr_clk(void);
 #endif
 
 /* EEPROM */
-#define CONFIG_ID_EEPROM
 #define CONFIG_SYS_I2C_EEPROM_NXID
 #define CONFIG_SYS_EEPROM_BUS_NUM              0
-#define CONFIG_SYS_I2C_EEPROM_ADDR             0x57
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN         1
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS      3
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS  5
 
 /*
  * I2C bus multiplexer
@@ -429,8 +387,6 @@ unsigned long get_board_ddr_clk(void);
 #define CONFIG_PCI_SCAN_SHOW
 #endif
 
-#define CONFIG_CMDLINE_TAG
-
 #define CONFIG_PEN_ADDR_BIG_ENDIAN
 #define CONFIG_LAYERSCAPE_NS_ACCESS
 #define CONFIG_SMP_PEN_ADDR            0x01ee0200
@@ -461,8 +417,6 @@ unsigned long get_board_ddr_clk(void);
  */
 #define CONFIG_SYS_BOOTMAPSZ           (256 << 20)
 
-#define CONFIG_SYS_LOAD_ADDR           0x82000000
-
 #define CONFIG_LS102XA_STREAM_ID
 
 #define CONFIG_SYS_INIT_SP_OFFSET \