serial: Use the default CONFIG_SYS_BAUDRATE_TABLE in more platforms

[platform/kernel/u-boot.git] / include / configs / ls1012a_common.h

diff --git a/include/configs/ls1012a_common.h b/include/configs/ls1012a_common.h
index e9baa2a..8a49f2d 100644 (file)
--- a/include/configs/ls1012a_common.h
+++ b/include/configs/ls1012a_common.h
@@ -6,21 +6,17 @@
 #ifndef __LS1012A_COMMON_H
 #define __LS1012A_COMMON_H
 
-#define CONFIG_GICV2
-
 #include <asm/arch/config.h>
 #include <asm/arch/stream_id_lsch2.h>
+#include <linux/sizes.h>
 
 #define CONFIG_SYS_CLK_FREQ            125000000
 
-#define CONFIG_SKIP_LOWLEVEL_INIT
-
 #ifdef CONFIG_TFABOOT
 #define CONFIG_SYS_INIT_SP_ADDR                CONFIG_SYS_TEXT_BASE
 #else
 #define CONFIG_SYS_INIT_SP_ADDR                (CONFIG_SYS_FSL_OCRAM_BASE + 0xfff0)
 #endif
-#define CONFIG_SYS_LOAD_ADDR   (CONFIG_SYS_DDR_SDRAM_BASE + 0x10000000)
 
 #define CONFIG_SYS_DDR_SDRAM_BASE      0x80000000
 #define CONFIG_SYS_FSL_DDR_SDRAM_BASE_PHY      0
@@ -33,27 +29,12 @@
 /* CSU */
 #define CONFIG_LAYERSCAPE_NS_ACCESS
 
-/* Size of malloc() pool */
-#define CONFIG_SYS_MALLOC_LEN          (CONFIG_ENV_SIZE + 128 * 1024)
-
-/*SPI device */
-#if defined(CONFIG_QSPI_BOOT) || defined(CONFIG_TFABOOT)
+/* PFE */
 #define CONFIG_SYS_FMAN_FW_ADDR                0x400d0000
-#define CONFIG_SPI_FLASH_SPANSION
-#define CONFIG_FSL_SPI_INTERFACE
-#define CONFIG_SF_DATAFLASH
+#define CONFIG_SYS_QE_FMAN_FW_LENGTH   0x300000
 
-#define QSPI0_AMBA_BASE                0x40000000
-#define CONFIG_SPI_FLASH_SPANSION
-
-#define FSL_QSPI_FLASH_SIZE            SZ_64M
-#define FSL_QSPI_FLASH_NUM             2
-
-/*
- * Environment
- */
-#define CONFIG_ENV_OVERWRITE
-#endif
+/*SPI device */
+#define CONFIG_SYS_FSL_QSPI_BASE       0x40000000
 
 /* SATA */
 #define CONFIG_SCSI_AHCI_PLAT
@@ -66,19 +47,18 @@
                                                CONFIG_SYS_SCSI_MAX_LUN)
 
 /* I2C */
-#ifndef CONFIG_DM_I2C
-#define CONFIG_SYS_I2C
-#else
-#define CONFIG_I2C_SET_DEFAULT_BUS_NUM
-#define CONFIG_I2C_DEFAULT_BUS_NUMBER 0
+
+/* GPIO */
+#ifdef CONFIG_DM_GPIO
+#ifndef CONFIG_MPC8XXX_GPIO
+#define CONFIG_MPC8XXX_GPIO
+#endif
 #endif
 
 #define CONFIG_SYS_NS16550_SERIAL
 #define CONFIG_SYS_NS16550_REG_SIZE     1
 #define CONFIG_SYS_NS16550_CLK          (get_serial_clock())
 
-#define CONFIG_SYS_BAUDRATE_TABLE      { 9600, 19200, 38400, 57600, 115200 }
-
 #define CONFIG_SYS_HZ                  1000
 
 #define CONFIG_HWCONFIG
@@ -98,19 +78,19 @@
        "verify=no\0"                           \
        "loadaddr=0x80100000\0"                 \
        "kernel_addr=0x100000\0"                \
-       "fdt_high=0xffffffffffffffff\0"         \
        "initrd_high=0xffffffffffffffff\0"      \
        "kernel_start=0x1000000\0"              \
        "kernel_load=0xa0000000\0"              \
        "kernel_size=0x2800000\0"               \
+       "bootm_size=0x10000000\0"               \
 
 #undef CONFIG_BOOTCOMMAND
 #ifdef CONFIG_TFABOOT
-#define QSPI_NOR_BOOTCOMMAND   "pfe stop; sf probe 0:0; sf read $kernel_load "\
+#define QSPI_NOR_BOOTCOMMAND   "sf probe 0:0; sf read $kernel_load "\
                                "$kernel_start $kernel_size && "\
                                "bootm $kernel_load"
 #else
-#define CONFIG_BOOTCOMMAND     "pfe stop; sf probe 0:0; sf read $kernel_load "\
+#define CONFIG_BOOTCOMMAND     "sf probe 0:0; sf read $kernel_load "\
                                "$kernel_start $kernel_size && "\
                                "bootm $kernel_load"
 #endif