Convert CONFIG_SCSI_AHCI_PLAT et al to Kconfig

[platform/kernel/u-boot.git] / include / configs / ls1012a_common.h

diff --git a/include/configs/ls1012a_common.h b/include/configs/ls1012a_common.h
index 74af0b9..f92ff17 100644 (file)
--- a/include/configs/ls1012a_common.h
+++ b/include/configs/ls1012a_common.h
@@ -1,30 +1,20 @@
+/* SPDX-License-Identifier: GPL-2.0+ */
 /*
  * Copyright 2016 Freescale Semiconductor
- *
- * SPDX-License-Identifier:    GPL-2.0+
  */
 
 #ifndef __LS1012A_COMMON_H
 #define __LS1012A_COMMON_H
 
-#define CONFIG_FSL_LAYERSCAPE
-#define CONFIG_GICV2
-
 #include <asm/arch/config.h>
 #include <asm/arch/stream_id_lsch2.h>
+#include <linux/sizes.h>
 
-#define CONFIG_SUPPORT_RAW_INITRD
-
-#define CONFIG_DISPLAY_BOARDINFO_LATE
-
-#define CONFIG_SYS_TEXT_BASE           0x40100000
-
-#define CONFIG_SYS_CLK_FREQ            125000000
-
-#define CONFIG_SKIP_LOWLEVEL_INIT
-
+#ifdef CONFIG_TFABOOT
+#define CONFIG_SYS_INIT_SP_ADDR                CONFIG_SYS_TEXT_BASE
+#else
 #define CONFIG_SYS_INIT_SP_ADDR                (CONFIG_SYS_FSL_OCRAM_BASE + 0xfff0)
-#define CONFIG_SYS_LOAD_ADDR   (CONFIG_SYS_DDR_SDRAM_BASE + 0x10000000)
+#endif
 
 #define CONFIG_SYS_DDR_SDRAM_BASE      0x80000000
 #define CONFIG_SYS_FSL_DDR_SDRAM_BASE_PHY      0
@@ -32,92 +22,59 @@
 #define CONFIG_SYS_DDR_BLOCK2_BASE     0x880000000ULL
 
 /* Generic Timer Definitions */
-#define COUNTER_FREQUENCY              CONFIG_SYS_CLK_FREQ/4   /* 25MHz */
+#define COUNTER_FREQUENCY              25000000        /* 25MHz */
 
 /* CSU */
 #define CONFIG_LAYERSCAPE_NS_ACCESS
 
-/* Size of malloc() pool */
-#define CONFIG_SYS_MALLOC_LEN          (CONFIG_ENV_SIZE + 128 * 1024)
-
 /*SPI device */
-#ifdef CONFIG_QSPI_BOOT
-#define CONFIG_SYS_QE_FW_IN_SPIFLASH
-#define CONFIG_SYS_FMAN_FW_ADDR                0x400d0000
-#define CONFIG_ENV_SPI_BUS             0
-#define CONFIG_ENV_SPI_CS              0
-#define CONFIG_ENV_SPI_MAX_HZ          1000000
-#define CONFIG_ENV_SPI_MODE            0x03
-#define CONFIG_SPI_FLASH_SPANSION
-#define CONFIG_FSL_SPI_INTERFACE
-#define CONFIG_SF_DATAFLASH
-
-#define CONFIG_FSL_QSPI
-#define QSPI0_AMBA_BASE                0x40000000
-#define CONFIG_SPI_FLASH_SPANSION
-
-#define FSL_QSPI_FLASH_SIZE            SZ_64M
-#define FSL_QSPI_FLASH_NUM             2
+#define CONFIG_SYS_FSL_QSPI_BASE       0x40000000
 
-/*
- * Environment
- */
-#define CONFIG_ENV_OVERWRITE
+/* SATA */
 
-#define CONFIG_ENV_SIZE                        0x40000          /* 256KB */
-#define CONFIG_ENV_OFFSET              0x200000        /* 2MB */
-#define CONFIG_ENV_SECT_SIZE           0x40000
-#endif
+#define CONFIG_SYS_SATA                                AHCI_BASE_ADDR
 
 /* I2C */
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_I2C_MXC
-#define CONFIG_SYS_I2C_MXC_I2C1                /* enable I2C bus 1 */
-#define CONFIG_SYS_I2C_MXC_I2C2                /* enable I2C bus 2 */
 
-#define CONFIG_CONS_INDEX       1
+/* GPIO */
+
 #define CONFIG_SYS_NS16550_SERIAL
 #define CONFIG_SYS_NS16550_REG_SIZE     1
 #define CONFIG_SYS_NS16550_CLK          (get_serial_clock())
 
-#define CONFIG_SYS_BAUDRATE_TABLE      { 9600, 19200, 38400, 57600, 115200 }
-
-/* Command line configuration */
-#undef CONFIG_CMD_IMLS
-
-#define CONFIG_SYS_HZ                  1000
-
 #define CONFIG_HWCONFIG
 #define HWCONFIG_BUFFER_SIZE           128
 
+#ifndef CONFIG_SPL_BUILD
+#define BOOT_TARGET_DEVICES(func) \
+       func(MMC, mmc, 0) \
+       func(USB, usb, 0) \
+       func(SCSI, scsi, 0) \
+       func(DHCP, dhcp, na)
+#include <config_distro_bootcmd.h>
+#endif
+
 /* Initial environment variables */
 #define CONFIG_EXTRA_ENV_SETTINGS              \
        "verify=no\0"                           \
        "loadaddr=0x80100000\0"                 \
        "kernel_addr=0x100000\0"                \
-       "fdt_high=0xffffffffffffffff\0"         \
        "initrd_high=0xffffffffffffffff\0"      \
-       "kernel_start=0xa00000\0"               \
+       "kernel_start=0x1000000\0"              \
        "kernel_load=0xa0000000\0"              \
        "kernel_size=0x2800000\0"               \
+       "bootm_size=0x10000000\0"               \
 
-#define CONFIG_BOOTARGS                "console=ttyS0,115200 root=/dev/ram0 " \
-                               "earlycon=uart8250,mmio,0x21c0500 quiet lpj=250000"
-#define CONFIG_BOOTCOMMAND             "sf probe 0:0; sf read $kernel_load "\
-                                       "$kernel_start $kernel_size && "\
-                                       "bootm $kernel_load"
+#ifdef CONFIG_TFABOOT
+#define QSPI_NOR_BOOTCOMMAND   "sf probe 0:0; sf read $kernel_load "\
+                               "$kernel_start $kernel_size && "\
+                               "bootm $kernel_load"
+#endif
 
 /* Monitor Command Prompt */
 #define CONFIG_SYS_CBSIZE              512     /* Console I/O Buffer Size */
-#define CONFIG_SYS_PBSIZE              (CONFIG_SYS_CBSIZE + \
-                                       sizeof(CONFIG_SYS_PROMPT) + 16)
-#define CONFIG_SYS_BARGSIZE            CONFIG_SYS_CBSIZE /* Boot args buffer */
-#define CONFIG_SYS_LONGHELP
-#define CONFIG_CMDLINE_EDITING         1
-#define CONFIG_AUTO_COMPLETE
 #define CONFIG_SYS_MAXARGS             64      /* max command args */
 
-#define CONFIG_PANIC_HANG
 #define CONFIG_SYS_BOOTM_LEN   (64 << 20)      /* Increase max gunzip size */
 
 #include <asm/arch/soc.h>