#ifndef __CONFIG_H
#define __CONFIG_H
+/*
+ * Valid values for CONFIG_SYS_TEXT_BASE are:
+ *
+ * Standard configuration - all models
+ * 0xFFF00000 boot from flash
+ *
+ * Test configuration (boot from RAM using uloader.o)
+ * LinkStation HD-HLAN and KuroBox Standard
+ * 0x03F00000 boot from RAM
+ * LinkStation HD-HGLAN and KuroBox HG
+ * 0x07F00000 boot from RAM
+ */
+#ifndef CONFIG_SYS_TEXT_BASE
+#define CONFIG_SYS_TEXT_BASE 0xFFF00000
+#endif
+
#if 0
#define DEBUG
#endif
#define CONFIG_OF_LIBFDT 1
-#define OF_CPU "PowerPC,603e"
-#define OF_SOC "soc10x@80000000"
#define OF_STDOUT_PATH "/soc10x/serial@80004600"
/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
#define CONFIG_SYS_CONSOLE_IS_IN_ENV
-#define XMK_STR(x) #x
-#define MK_STR(x) XMK_STR(x)
-
#if defined(CONFIG_HLAN) || defined(CONFIG_LAN)
#define UBFILE "share/u-boot/u-boot-hd.flash.bin"
#elif defined(CONFIG_HGLAN)
"stdin=nc\0" \
"stdout=nc\0" \
"stderr=nc\0" \
- "ipaddr="MK_STR(CONFIG_IPADDR_LS)"\0" \
+ "ipaddr="__stringify(CONFIG_IPADDR_LS)"\0" \
"netmask=255.255.255.0\0" \
- "serverip="MK_STR(CONFIG_SERVERIP_LS)"\0" \
- "ncip="MK_STR(CONFIG_NCIP_LS)"\0" \
+ "serverip="__stringify(CONFIG_SERVERIP_LS)"\0" \
+ "ncip="__stringify(CONFIG_NCIP_LS)"\0" \
"netretry=no\0" \
"nc=setenv stdin nc;setenv stdout nc;setenv stderr nc\0" \
"ser=setenv stdin serial;setenv stdout serial;setenv stderr serial\0" \
/*-----------------------------------------------------------------------
* Ethernet stuff
*/
-#define CONFIG_NET_MULTI
#if defined(CONFIG_LAN) || defined(CONFIG_HLAN)
#define CONFIG_TULIP
#define CONFIG_SYS_FLASH_BASE 0xFFC00000
#define CONFIG_SYS_FLASH_SIZE 0x00400000
-#define CONFIG_SYS_MONITOR_BASE TEXT_BASE
+#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
#define CONFIG_SYS_RESET_ADDRESS 0xFFF00100
#define CONFIG_SYS_EUMB_ADDR 0x80000000
#endif
/*-----------------------------------------------------------------------
- * Change TEXT_BASE in bord/linkstation/config.mk to get a RAM build
+ * Change CONFIG_SYS_TEXT_BASE in bord/linkstation/config.mk to get a RAM build
*
* RAM based builds are for testing purposes. A Linux module, uloader.o,
* exists to load U-Boot and pass control to it
#else
#define CONFIG_SYS_INIT_RAM_ADDR 0x40000000
#endif
-#define CONFIG_SYS_INIT_RAM_END 0x1000
-#define CONFIG_SYS_GBL_DATA_SIZE 128
-#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_RAM_SIZE 0x1000
+#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
/*----------------------------------------------------------------------
* Serial configuration
*/
#define CONFIG_CONS_INDEX 1
#define CONFIG_BAUDRATE 57600
-#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
#define CONFIG_SYS_NS16550
#define CONFIG_SYS_NS16550_SERIAL
* taken from the orignal Linkstation boot code
*
* Most of the low level configuration setttings are normally used
- * in cpu/mpc824x/cpu_init.c which is NOT used by this implementation.
+ * in arch/powerpc/cpu/mpc824x/cpu_init.c which is NOT used by this implementation.
* Low level initialisation is done in board/linkstation/early_init.S
* The values below are included for reference purpose only
*/
*/
#define CONFIG_DOS_PARTITION
-/*-----------------------------------------------------------------------
- * Internal Definitions
- *
- * Boot Flags
- */
-#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
-#define BOOTFLAG_WARM 0x02 /* Software reboot */
-
#endif /* __CONFIG_H */