i2c, ppc4xx_i2c: switch to new multibus/multiadapter support

[platform/kernel/u-boot.git] / include / configs / korat.h

diff --git a/include/configs/korat.h b/include/configs/korat.h
index 3a0531b..c2e7118 100644 (file)
--- a/include/configs/korat.h
+++ b/include/configs/korat.h
@@ -88,9 +88,8 @@
 /* 440EPx has 16KB of internal SRAM, so no need for D-Cache            */
 #undef CONFIG_SYS_INIT_RAM_DCACHE
 #define CONFIG_SYS_INIT_RAM_ADDR       CONFIG_SYS_OCM_BASE     /* OCM                  */
-#define CONFIG_SYS_INIT_RAM_END        (4 << 10)
-#define CONFIG_SYS_GBL_DATA_SIZE       256     /* num bytes initial data       */
-#define CONFIG_SYS_GBL_DATA_OFFSET     (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_RAM_SIZE       (4 << 10)
+#define CONFIG_SYS_GBL_DATA_OFFSET     (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 #define CONFIG_SYS_INIT_SP_OFFSET      (CONFIG_SYS_GBL_DATA_OFFSET - 0x4)
 
 /*
@@ -103,7 +102,6 @@
 #define CONFIG_SYS_NS16550_CLK         get_serial_clock()
 #define CONFIG_SYS_EXT_SERIAL_CLOCK    11059200        /* ext. 11.059MHz clk   */
 #define CONFIG_BAUDRATE                115200
-#define CONFIG_SERIAL_MULTI    1
 
 #define CONFIG_SYS_BAUDRATE_TABLE                                              \
        {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
@@ -157,11 +155,11 @@
 /*
  * I2C
  */
-#define CONFIG_HARD_I2C                1       /* I2C with hardware support    */
-#undef CONFIG_SOFT_I2C                 /* I2C bit-banged               */
-#define CONFIG_PPC4XX_I2C              /* use PPC4xx driver            */
-#define CONFIG_SYS_I2C_SPEED           400000  /* I2C speed and slave address  */
-#define CONFIG_SYS_I2C_SLAVE           0x7F
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_PPC4XX
+#define CONFIG_SYS_I2C_PPC4XX_CH0
+#define CONFIG_SYS_I2C_PPC4XX_SPEED_0          400000
+#define CONFIG_SYS_I2C_PPC4XX_SLAVE_0          0x7F
 
 #define CONFIG_SYS_I2C_MULTI_EEPROMS
 #define CONFIG_SYS_I2C_EEPROM_ADDR     (0xa8>>1)
@@ -251,7 +249,6 @@
 #define CONFIG_HAS_ETH0
 #define CONFIG_SYS_RX_ETH_BUFFER       32      /* Number of ethernet rx        */
                                        /*   buffers & descriptors      */
-#define CONFIG_NET_MULTI       1
 #define CONFIG_HAS_ETH1                1       /* add support for "eth1addr"   */
 #define CONFIG_PHY1_ADDR       3
 
@@ -358,6 +355,7 @@
  */
 /* General PCI */
 #define CONFIG_PCI                     /* include pci support          */
+#define CONFIG_PCI_INDIRECT_BRIDGE     /* indirect PCI bridge support */
 #define CONFIG_PCI_PNP                 /* do pci plug-and-play         */
 #define CONFIG_SYS_PCI_CACHE_LINE_SIZE 0       /* to avoid problems with PNP   */
 #define CONFIG_PCI_SCAN_SHOW           /* show pci devices on startup  */