Makefile: move all Power Architecture boards into boards.cfg

[platform/kernel/u-boot.git] / include / configs / korat.h

diff --git a/include/configs/korat.h b/include/configs/korat.h
index 026dd08..96a984d 100644 (file)
--- a/include/configs/korat.h
+++ b/include/configs/korat.h
@@ -38,6 +38,12 @@
 #define CONFIG_4xx             1       /* ... PPC4xx family            */
 #define CONFIG_SYS_CLK_FREQ    33333333
 
+#ifdef CONFIG_KORAT_PERMANENT
+#define CONFIG_SYS_TEXT_BASE   0xFFFA0000
+#else
+#define        CONFIG_SYS_TEXT_BASE    0xF7F60000
+#endif
+
 #define CONFIG_BOARD_EARLY_INIT_F 1    /* Call board_early_init_f      */
 #define CONFIG_MISC_INIT_R     1       /* Call misc_init_r             */
 
@@ -64,16 +70,13 @@
 #define CONFIG_SYS_FLASH1_MAX_SIZE     0x08000000
 #define CONFIG_SYS_FLASH1_ADDR         (CONFIG_SYS_FLASH1_TOP - CONFIG_SYS_FLASH1_MAX_SIZE)
 #define CONFIG_SYS_FLASH_BASE          CONFIG_SYS_FLASH1_ADDR  /* start of FLASH       */
-#define CONFIG_SYS_MONITOR_BASE        TEXT_BASE
+#define CONFIG_SYS_MONITOR_BASE        CONFIG_SYS_TEXT_BASE
 #define CONFIG_SYS_OCM_BASE            0xe0010000      /* ocm                  */
 #define CONFIG_SYS_OCM_DATA_ADDR       CONFIG_SYS_OCM_BASE
 #define CONFIG_SYS_PCI_BASE            0xe0000000      /* Internal PCI regs    */
 #define CONFIG_SYS_PCI_MEMBASE         0x80000000      /* mapped pci memory    */
 #define CONFIG_SYS_PCI_MEMBASE2                (CONFIG_SYS_PCI_MEMBASE + 0x20000000)
 
-/* Don't change either of these */
-#define CONFIG_SYS_PERIPHERAL_BASE     0xef600000      /* internal peripherals */
-
 #define CONFIG_SYS_USB2D0_BASE         0xe0000100
 #define CONFIG_SYS_USB_DEVICE          0xe0000000
 #define CONFIG_SYS_USB_HOST            0xe0000400
@@ -88,16 +91,19 @@
 #define CONFIG_SYS_INIT_RAM_END        (4 << 10)
 #define CONFIG_SYS_GBL_DATA_SIZE       256     /* num bytes initial data       */
 #define CONFIG_SYS_GBL_DATA_OFFSET     (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET      CONFIG_SYS_POST_WORD_ADDR
+#define CONFIG_SYS_INIT_SP_OFFSET      (CONFIG_SYS_GBL_DATA_OFFSET - 0x4)
 
 /*
  * Serial Port
  */
+#define CONFIG_CONS_INDEX      1       /* Use UART0                    */
+#define CONFIG_SYS_NS16550
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE    1
+#define CONFIG_SYS_NS16550_CLK         get_serial_clock()
 #define CONFIG_SYS_EXT_SERIAL_CLOCK    11059200        /* ext. 11.059MHz clk   */
 #define CONFIG_BAUDRATE                115200
 #define CONFIG_SERIAL_MULTI    1
-/* define this if you want console on UART1 */
-#undef CONFIG_UART1_CONSOLE
 
 #define CONFIG_SYS_BAUDRATE_TABLE                                              \
        {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
@@ -153,6 +159,7 @@
  */
 #define CONFIG_HARD_I2C                1       /* I2C with hardware support    */
 #undef CONFIG_SOFT_I2C                 /* I2C bit-banged               */
+#define CONFIG_PPC4XX_I2C              /* use PPC4xx driver            */
 #define CONFIG_SYS_I2C_SPEED           400000  /* I2C speed and slave address  */
 #define CONFIG_SYS_I2C_SLAVE           0x7F
 
@@ -305,7 +312,6 @@
                                 CONFIG_SYS_POST_SPR    | \
                                 CONFIG_SYS_POST_UART)
 
-#define CONFIG_SYS_POST_WORD_ADDR      (CONFIG_SYS_GBL_DATA_OFFSET - 0x4)
 #define CONFIG_LOGBUFFER
 #define CONFIG_SYS_POST_CACHE_ADDR     0xC8000000      /* free virtual address     */