+/* SPDX-License-Identifier: GPL-2.0+ */
/*
- * Copyright (C) 2006 Freescale Semiconductor, Inc.
- * Dave Liu <daveliu@freescale.com>
- *
- * Copyright (C) 2007 Logic Product Development, Inc.
- * Peter Barada <peterb@logicpd.com>
- *
- * Copyright (C) 2007 MontaVista Software, Inc.
- * Anton Vorontsov <avorontsov@ru.mvista.com>
- *
- * (C) Copyright 2008
- * Heiko Schocher, DENX Software Engineering, hs@denx.de.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
+ * (C) Copyright 2012
+ * Holger Brunck, Keymile GmbH Hannover, <holger.brunck@keymile.com>
+ * Christian Herzig, Keymile AG Switzerland, <christian.herzig@keymile.com>
*/
#ifndef __CONFIG_H
#define __CONFIG_H
-/*
- * High Level Configuration Options
- */
-#define CONFIG_E300 1 /* E300 family */
-#define CONFIG_QE 1 /* Has QE */
-#define CONFIG_MPC83xx 1 /* MPC83xx family */
-#define CONFIG_MPC8360 1 /* MPC8360 CPU specific */
-#define CONFIG_KMETER1 1 /* KMETER1 board specific */
-#define CONFIG_HOSTNAME kmeter1
+#define CONFIG_HOSTNAME "kmeter1"
/* include common defines/options for all Keymile boards */
-#include "keymile-common.h"
-
-#define CONFIG_KM_UBI_PARTITION_NAME "ubi0"
-
-#define MTDIDS_DEFAULT "nor0=boot"
-#define MTDPARTS_DEFAULT \
- "mtdparts=boot:768k(u-boot),128k(env),128k(envred)," \
- "-(" CONFIG_KM_UBI_PARTITION_NAME ")"
-
-#define CONFIG_MISC_INIT_R 1
-/*
- * System Clock Setup
- */
-#define CONFIG_83XX_CLKIN 66000000
-#define CONFIG_SYS_CLK_FREQ 66000000
-#define CONFIG_83XX_PCICLK 66000000
-
-/*
- * Hardware Reset Configuration Word
- */
-#define CONFIG_SYS_HRCW_LOW (\
- HRCWL_CSB_TO_CLKIN_4X1 | \
- HRCWL_CORE_TO_CSB_2X1 | \
- HRCWL_CE_PLL_VCO_DIV_2 | \
- HRCWL_CE_TO_PLL_1X6 )
-
-#define CONFIG_SYS_HRCW_HIGH (\
- HRCWH_CORE_ENABLE | \
- HRCWH_FROM_0X00000100 | \
- HRCWH_BOOTSEQ_DISABLE | \
- HRCWH_SW_WATCHDOG_DISABLE | \
- HRCWH_ROM_LOC_LOCAL_16BIT | \
- HRCWH_BIG_ENDIAN | \
- HRCWH_LALE_EARLY | \
- HRCWH_LDP_CLEAR )
-
-/*
- * System IO Config
- */
-#define CONFIG_SYS_SICRH 0x00000006
-#define CONFIG_SYS_SICRL 0x00000000
-
-/*
- * IMMR new address
- */
-#define CONFIG_SYS_IMMR 0xE0000000
-
-/*
- * Bus Arbitration Configuration Register (ACR)
- */
-#define CONFIG_SYS_ACR_PIPE_DEP 3 /* pipeline depth 4 transactions */
-#define CONFIG_SYS_ACR_RPTCNT 3 /* 4 consecutive transactions */
-#define CONFIG_SYS_ACR_APARK 0 /* park bus to master (below) */
-#define CONFIG_SYS_ACR_PARKM 3 /* parking master = QuiccEngine */
-
-/*
- * DDR Setup
- */
-#define CONFIG_SYS_DDR_BASE 0x00000000 /* DDR is system memory */
-#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_BASE
-#define CONFIG_SYS_DDR_SDRAM_BASE CONFIG_SYS_DDR_BASE
-#define CONFIG_SYS_DDR_SDRAM_CLK_CNTL (DDR_SDRAM_CLK_CNTL_SS_EN | \
- DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05)
+#include "km/keymile-common.h"
+#include "km/km-powerpc.h"
+#include "km/km-mpc83xx.h"
+#include "km/km-mpc8360.h"
-#define CFG_83XX_DDR_USES_CS0
-
-#undef CONFIG_DDR_ECC
-
-/*
- * DDRCDR - DDR Control Driver Register
- */
-
-#undef CONFIG_SPD_EEPROM /* Do not use SPD EEPROM for DDR setup */
-
-/*
- * Manually set up DDR parameters
- */
-#define CONFIG_DDR_II
-#define CONFIG_SYS_DDR_SIZE 2048 /* MB */
-#define CONFIG_SYS_DDR_CS0_BNDS 0x0000007f
#define CONFIG_SYS_DDR_CS0_CONFIG (CSCONFIG_EN | CSCONFIG_AP | \
CSCONFIG_ROW_BIT_13 | \
- CSCONFIG_COL_BIT_10 | CSCONFIG_ODT_WR_ACS)
-
-#define CONFIG_SYS_DDR_SDRAM_CFG (SDRAM_CFG_SDRAM_TYPE_DDR2 | \
- SDRAM_CFG_SREN)
-#define CONFIG_SYS_DDR_SDRAM_CFG2 0x00401000
-#define CONFIG_SYS_DDR_CLK_CNTL (DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05)
-#define CONFIG_SYS_DDR_INTERVAL ((0x080 << SDRAM_INTERVAL_BSTOPRE_SHIFT) | \
- (0x3cf << SDRAM_INTERVAL_REFINT_SHIFT))
-
-#define CONFIG_SYS_DDRCDR 0x40000001
-#define CONFIG_SYS_DDR_MODE 0x47860452
-#define CONFIG_SYS_DDR_MODE2 0x8080c000
-
-#define CONFIG_SYS_DDR_TIMING_0 ((2 << TIMING_CFG0_MRS_CYC_SHIFT) | \
- (8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) | \
- (6 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) | \
- (2 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) | \
- (0 << TIMING_CFG0_WWT_SHIFT) | \
- (0 << TIMING_CFG0_RRT_SHIFT) | \
- (0 << TIMING_CFG0_WRT_SHIFT) | \
- (0 << TIMING_CFG0_RWT_SHIFT))
-
-#define CONFIG_SYS_DDR_TIMING_1 (( TIMING_CFG1_CASLAT_50) | \
- ( 2 << TIMING_CFG1_WRTORD_SHIFT) | \
- ( 2 << TIMING_CFG1_ACTTOACT_SHIFT) | \
- ( 3 << TIMING_CFG1_WRREC_SHIFT) | \
- ( 7 << TIMING_CFG1_REFREC_SHIFT) | \
- ( 3 << TIMING_CFG1_ACTTORW_SHIFT) | \
- ( 8 << TIMING_CFG1_ACTTOPRE_SHIFT) | \
- ( 3 << TIMING_CFG1_PRETOACT_SHIFT))
-
-#define CONFIG_SYS_DDR_TIMING_2 ((8 << TIMING_CFG2_FOUR_ACT_SHIFT) | \
- (3 << TIMING_CFG2_CKE_PLS_SHIFT) | \
- (2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) | \
- (2 << TIMING_CFG2_RD_TO_PRE_SHIFT) | \
- (4 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) | \
- (0 << TIMING_CFG2_ADD_LAT_SHIFT) | \
- (5 << TIMING_CFG2_CPO_SHIFT))
-
-#define CONFIG_SYS_DDR_TIMING_3 0x00000000
-
-/*
- * The reserved memory
- */
-#define CONFIG_SYS_MONITOR_BASE TEXT_BASE /* start of monitor */
-#define CONFIG_SYS_FLASH_BASE 0xF0000000
-#define CONFIG_SYS_PIGGY_BASE 0xE8000000
-#define CONFIG_SYS_PIGGY_SIZE 128
-#define CONFIG_SYS_PAXE_BASE 0xA0000000
-#define CONFIG_SYS_PAXE_SIZE 512
-
-#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
-#define CONFIG_SYS_RAMBOOT
-#else
-#undef CONFIG_SYS_RAMBOOT
-#endif
-
-#define CONFIG_SYS_MONITOR_LEN (384 * 1024) /* Reserve 384 kB for Mon */
-
-/*
- * Initial RAM Base Address Setup
- */
-#define CONFIG_SYS_INIT_RAM_LOCK 1
-#define CONFIG_SYS_INIT_RAM_ADDR 0xE6000000 /* Initial RAM address */
-#define CONFIG_SYS_INIT_RAM_END 0x1000 /* End of used area in RAM */
-#define CONFIG_SYS_GBL_DATA_SIZE 0x100 /* num bytes initial data */
-#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
-
-/*
- * Local Bus Configuration & Clock Setup
- */
-#define CONFIG_SYS_LCRR_DBYP LCRR_DBYP
-#define CONFIG_SYS_LCRR_EADC LCRR_EADC_2
-#define CONFIG_SYS_LCRR_CLKDIV LCRR_CLKDIV_4
-
-/*
- * Init Local Bus Memory Controller:
- *
- * Bank Bus Machine PortSz Size Device
- * ---- --- ------- ------ ----- ------
- * 0 Local GPCM 16 bit 256MB FLASH
- * 1 Local GPCM 8 bit 128MB GPIO/PIGGY
- * 3 Local GPCM 8 bit 512MB PAXE
- *
- */
-/*
- * FLASH on the Local Bus
- */
-#define CONFIG_SYS_FLASH_CFI /* use the Common Flash Interface */
-#define CONFIG_FLASH_CFI_DRIVER /* use the CFI driver */
-#define CONFIG_SYS_FLASH_SIZE 256 /* max FLASH size is 256M */
-#define CONFIG_SYS_FLASH_PROTECTION 1
-#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1
-
-#define CONFIG_SYS_LBLAWBAR0_PRELIM CONFIG_SYS_FLASH_BASE /* Window base at flash base */
-#define CONFIG_SYS_LBLAWAR0_PRELIM 0x8000001b /* 256MB window size */
-
-#define CONFIG_SYS_BR0_PRELIM (CONFIG_SYS_FLASH_BASE | \
- (2 << BR_PS_SHIFT) | /* 16 bit port size */ \
- BR_V)
-
-#define CONFIG_SYS_OR0_PRELIM (MEG_TO_AM(CONFIG_SYS_FLASH_SIZE) | \
- OR_GPCM_CSNT | OR_GPCM_ACS_DIV2 | \
- OR_GPCM_SCY_5 | \
- OR_GPCM_TRLX | OR_GPCM_EAD)
-
-#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max num of flash banks */
-#define CONFIG_SYS_MAX_FLASH_SECT 512 /* max num of sects on one chip */
-#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE }
-
-#undef CONFIG_SYS_FLASH_CHECKSUM
-
-/*
- * PRIO1/PIGGY on the local bus CS1
- */
-#define CONFIG_SYS_LBLAWBAR1_PRELIM CONFIG_SYS_PIGGY_BASE /* Window base at flash base */
-#define CONFIG_SYS_LBLAWAR1_PRELIM 0x8000001A /* 128MB window size */
-
-#define CONFIG_SYS_BR1_PRELIM (CONFIG_SYS_PIGGY_BASE | \
- (1 << BR_PS_SHIFT) | /* 8 bit port size */ \
- BR_V)
-#define CONFIG_SYS_OR1_PRELIM (MEG_TO_AM(CONFIG_SYS_PIGGY_SIZE) | /* 128MB */ \
- OR_GPCM_CSNT | OR_GPCM_ACS_DIV2 | \
- OR_GPCM_SCY_2 | \
- OR_GPCM_TRLX | OR_GPCM_EAD)
-
-/*
- * PAXE on the local bus CS3
- */
-#define CONFIG_SYS_LBLAWBAR3_PRELIM CONFIG_SYS_PAXE_BASE /* Window base at flash base */
-#define CONFIG_SYS_LBLAWAR3_PRELIM 0x8000001C /* 512MB window size */
-
-#define CONFIG_SYS_BR3_PRELIM (CONFIG_SYS_PAXE_BASE | \
- (1 << BR_PS_SHIFT) | /* 8 bit port size */ \
- BR_V)
-#define CONFIG_SYS_OR3_PRELIM (MEG_TO_AM(CONFIG_SYS_PAXE_SIZE) | \
- OR_GPCM_CSNT | OR_GPCM_ACS_DIV2 | \
- OR_GPCM_SCY_2 | \
- OR_GPCM_TRLX | OR_GPCM_EAD)
-
-/*
- * Serial Port
- */
-#define CONFIG_CONS_INDEX 1
-#undef CONFIG_SERIAL_SOFTWARE_FIFO
-#define CONFIG_SYS_NS16550
-#define CONFIG_SYS_NS16550_SERIAL
-#define CONFIG_SYS_NS16550_REG_SIZE 1
-#define CONFIG_SYS_NS16550_CLK get_bus_freq(0)
-
-#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR+0x4500)
-#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR+0x4600)
-
-/* Pass open firmware flat tree */
-#define CONFIG_OF_LIBFDT 1
-#define CONFIG_OF_BOARD_SETUP 1
-#define CONFIG_OF_STDOUT_VIA_ALIAS
-
-/*
- * General PCI
- * Addresses are mapped 1-1.
- */
-#undef CONFIG_PCI /* No PCI */
-
-#ifndef CONFIG_NET_MULTI
-#define CONFIG_NET_MULTI 1
-#endif
-/*
- * QE UEC ethernet configuration
- */
-#define CONFIG_UEC_ETH
-#define CONFIG_ETHPRIME "UEC0"
-
-#define CONFIG_UEC_ETH1 /* GETH1 */
-#define UEC_VERBOSE_DEBUG 1
-
-#ifdef CONFIG_UEC_ETH1
-#define CONFIG_SYS_UEC1_UCC_NUM 3 /* UCC4 */
-#define CONFIG_SYS_UEC1_RX_CLK QE_CLK_NONE /* not used in RMII Mode */
-#define CONFIG_SYS_UEC1_TX_CLK QE_CLK17
-#define CONFIG_SYS_UEC1_ETH_TYPE FAST_ETH
-#define CONFIG_SYS_UEC1_PHY_ADDR 0
-#define CONFIG_SYS_UEC1_INTERFACE_TYPE RMII
-#define CONFIG_SYS_UEC1_INTERFACE_SPEED 100
-#endif
-
-/*
- * Environment
- */
-
-#ifndef CONFIG_SYS_RAMBOOT
-#define CONFIG_ENV_IS_IN_FLASH 1
-#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN)
-#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K(one sector) for env */
-#define CONFIG_ENV_OFFSET (CONFIG_SYS_MONITOR_LEN)
-
-/* Address and size of Redundant Environment Sector */
-#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET+CONFIG_ENV_SECT_SIZE)
-#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE)
-
-#else /* CFG_RAMBOOT */
-#define CONFIG_SYS_NO_FLASH 1 /* Flash is not usable now */
-#define CONFIG_ENV_IS_NOWHERE 1 /* Store ENV in memory only */
-#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000)
-#define CONFIG_ENV_SIZE 0x2000
-#endif /* CFG_RAMBOOT */
-
-/* I2C */
-#define CONFIG_HARD_I2C /* I2C with hardware support */
-#undef CONFIG_SOFT_I2C /* I2C bit-banged */
-#define CONFIG_FSL_I2C
-#define CONFIG_SYS_I2C_SPEED 200000 /* I2C speed and slave address */
-#define CONFIG_SYS_I2C_SLAVE 0x7F
-#define CONFIG_SYS_I2C_OFFSET 0x3000
-#define CONFIG_I2C_MULTI_BUS 1
-#define CONFIG_I2C_MUX 1
-
-/* EEprom support */
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2
-
-/* I2C SYSMON (LM75, AD7414 is almost compatible) */
-#define CONFIG_DTT_LM75 1 /* ON Semi's LM75 */
-#define CONFIG_DTT_SENSORS {0, 1, 2, 3} /* Sensor addresses */
-#define CONFIG_SYS_DTT_MAX_TEMP 70
-#define CONFIG_SYS_DTT_LOW_TEMP -30
-#define CONFIG_SYS_DTT_HYSTERESIS 3
-#define CONFIG_SYS_DTT_BUS_NUM (CONFIG_SYS_MAX_I2C_BUS)
-
-#if defined(CONFIG_CMD_NAND)
-#define CONFIG_NAND_KMETER1
-#define CONFIG_SYS_MAX_NAND_DEVICE 1
-#define CONFIG_SYS_NAND_BASE CONFIG_SYS_PIGGY_BASE
-#endif
-
-#if defined(CONFIG_PCI)
-#define CONFIG_CMD_PCI
-#endif
-
-#if defined(CFG_RAMBOOT)
-#undef CONFIG_CMD_SAVEENV
-#undef CONFIG_CMD_LOADS
-#endif
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
-
-/*
- * Core HID Setup
- */
-#define CONFIG_SYS_HID0_INIT 0x000000000
-#define CONFIG_SYS_HID0_FINAL (HID0_ENABLE_MACHINE_CHECK | \
- HID0_ENABLE_INSTRUCTION_CACHE)
-#define CONFIG_SYS_HID2 HID2_HBE
-
-/*
- * MMU Setup
- */
-
-#define CONFIG_HIGH_BATS 1 /* High BATs supported */
-
-/* DDR: cache cacheable */
-#define CONFIG_SYS_IBAT0L (CONFIG_SYS_SDRAM_BASE | BATL_PP_10 | \
- BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
-#define CONFIG_SYS_IBAT0U (CONFIG_SYS_SDRAM_BASE | BATU_BL_256M | BATU_VS | BATU_VP)
-#define CONFIG_SYS_DBAT0L CONFIG_SYS_IBAT0L
-#define CONFIG_SYS_DBAT0U CONFIG_SYS_IBAT0U
-
-/* IMMRBAR & PCI IO: cache-inhibit and guarded */
-#define CONFIG_SYS_IBAT1L (CONFIG_SYS_IMMR | BATL_PP_10 | \
- BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
-#define CONFIG_SYS_IBAT1U (CONFIG_SYS_IMMR | BATU_BL_4M | BATU_VS | BATU_VP)
-#define CONFIG_SYS_DBAT1L CONFIG_SYS_IBAT1L
-#define CONFIG_SYS_DBAT1U CONFIG_SYS_IBAT1U
-
-/* PRIO1, PIGGY: icache cacheable, but dcache-inhibit and guarded */
-#define CONFIG_SYS_IBAT2L (CONFIG_SYS_PIGGY_BASE | BATL_PP_10 | BATL_MEMCOHERENCE)
-#define CONFIG_SYS_IBAT2U (CONFIG_SYS_PIGGY_BASE | BATU_BL_128M | BATU_VS | BATU_VP)
-#define CONFIG_SYS_DBAT2L (CONFIG_SYS_PIGGY_BASE | BATL_PP_10 | \
- BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
-#define CONFIG_SYS_DBAT2U CONFIG_SYS_IBAT2U
-
-/* FLASH: icache cacheable, but dcache-inhibit and guarded */
-#define CONFIG_SYS_IBAT3L (CONFIG_SYS_FLASH_BASE | BATL_PP_10 | BATL_MEMCOHERENCE)
-#define CONFIG_SYS_IBAT3U (CONFIG_SYS_FLASH_BASE | BATU_BL_256M | BATU_VS | BATU_VP)
-#define CONFIG_SYS_DBAT3L (CONFIG_SYS_FLASH_BASE | BATL_PP_10 | \
- BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
-#define CONFIG_SYS_DBAT3U CONFIG_SYS_IBAT3U
-
-/* Stack in dcache: cacheable, no memory coherence */
-#define CONFIG_SYS_IBAT4L (CONFIG_SYS_INIT_RAM_ADDR | BATL_PP_10)
-#define CONFIG_SYS_IBAT4U (CONFIG_SYS_INIT_RAM_ADDR | BATU_BL_128K | BATU_VS | BATU_VP)
-#define CONFIG_SYS_DBAT4L CONFIG_SYS_IBAT4L
-#define CONFIG_SYS_DBAT4U CONFIG_SYS_IBAT4U
-
-/* PAXE: icache cacheable, but dcache-inhibit and guarded */
-#define CONFIG_SYS_IBAT5L (CONFIG_SYS_PAXE_BASE | BATL_PP_10 | BATL_MEMCOHERENCE)
-#define CONFIG_SYS_IBAT5U (CONFIG_SYS_PAXE_BASE | BATU_BL_256M | BATU_VS | BATU_VP)
-#define CONFIG_SYS_DBAT5L (CONFIG_SYS_PAXE_BASE | BATL_PP_10 | \
- BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
-#define CONFIG_SYS_DBAT5U CONFIG_SYS_IBAT5U
-
-#ifdef CONFIG_PCI
-/* PCI MEM space: cacheable */
-#define CFG_IBAT6L (CFG_PCI1_MEM_PHYS | BATL_PP_10 | BATL_MEMCOHERENCE)
-#define CFG_IBAT6U (CFG_PCI1_MEM_PHYS | BATU_BL_256M | BATU_VS | BATU_VP)
-#define CFG_DBAT6L CFG_IBAT6L
-#define CFG_DBAT6U CFG_IBAT6U
-/* PCI MMIO space: cache-inhibit and guarded */
-#define CFG_IBAT7L (CFG_PCI1_MMIO_PHYS | BATL_PP_10 | \
- BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
-#define CFG_IBAT7U (CFG_PCI1_MMIO_PHYS | BATU_BL_256M | BATU_VS | BATU_VP)
-#define CFG_DBAT7L CFG_IBAT7L
-#define CFG_DBAT7U CFG_IBAT7U
-#else /* CONFIG_PCI */
-#define CONFIG_SYS_IBAT6L (0)
-#define CONFIG_SYS_IBAT6U (0)
-#define CONFIG_SYS_IBAT7L (0)
-#define CONFIG_SYS_IBAT7U (0)
-#define CONFIG_SYS_DBAT6L CONFIG_SYS_IBAT6L
-#define CONFIG_SYS_DBAT6U CONFIG_SYS_IBAT6U
-#define CONFIG_SYS_DBAT7L CONFIG_SYS_IBAT7L
-#define CONFIG_SYS_DBAT7U CONFIG_SYS_IBAT7U
-#endif /* CONFIG_PCI */
-
-/*
- * Internal Definitions
- *
- * Boot Flags
- */
-#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
-#define BOOTFLAG_WARM 0x02 /* Software reboot */
-
-#define BOOTFLASH_START F0000000
-
-#define CONFIG_PRAM 512 /* protected RAM [KBytes] */
-
-/*
- * Environment Configuration
- */
-#define CONFIG_ENV_OVERWRITE
-#ifndef CONFIG_KM_DEF_ENV /* if not set by keymile-common.h */
-#define CONFIG_KM_DEF_ENV "km-common=empty\0"
-#endif
-
-#define CONFIG_EXTRA_ENV_SETTINGS \
- CONFIG_KM_DEF_ENV \
- "rootpath=/opt/eldk/ppc_82xx\0" \
- "addcon=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\
- "ramdisk_file=/tftpboot/kmeter1/uRamdisk\0" \
- "loadram=tftp ${ramdisk_addr_r} ${ramdisk_file}\0" \
- "loadfdt=tftp ${fdt_addr_r} ${fdt_file}\0" \
- "loadkernel=tftp ${kernel_addr_r} ${bootfile}\0" \
- "unlock=yes\0" \
- "fdt_addr=F0080000\0" \
- "kernel_addr=F00a0000\0" \
- "ramdisk_addr=F03a0000\0" \
- "ramdisk_addr_r=F10000\0" \
- "EEprom_ivm=pca9547:70:9\0" \
- "dtt_bus=pca9547:70:a\0" \
- "mtdids=nor0=app \0" \
- "mtdparts=" MK_STR(MTDPARTS_DEFAULT) "\0" \
- ""
-
-#if defined(CONFIG_UEC_ETH)
-#define CONFIG_HAS_ETH0
-#endif
-
-#endif /* __CONFIG_H */
+ CSCONFIG_COL_BIT_10 | \
+ CSCONFIG_ODT_WR_ONLY_CURRENT)
+#endif /* CONFIG */