/*
* High Level Configuration Options (easy to change)
*/
-#define CONFIG_MARVELL
#define CONFIG_FEROCEON_88FR131 /* CPU Core subversion */
#define CONFIG_KW88F6281 /* SOC Name */
/* include common defines/options for all Keymile boards */
#include "keymile-common.h"
-/* SPI NOR Flash default params, used by sf commands */
-#define CONFIG_SF_DEFAULT_SPEED 8100000
-#define CONFIG_SF_DEFAULT_MODE SPI_MODE_3
-
-#if defined CONFIG_KM_ENV_IS_IN_SPI_NOR
-#define CONFIG_ENV_SPI_BUS 0
-#define CONFIG_ENV_SPI_CS 0
-#define CONFIG_ENV_SPI_MAX_HZ 8100000
-#define CONFIG_ENV_SPI_MODE SPI_MODE_3
-#endif
-
/* Reserve 4 MB for malloc */
#define CONFIG_SYS_MALLOC_LEN (4 * 1024 * 1024)
#include "asm/arch/config.h"
-#define CONFIG_SYS_MEMTEST_START 0x00400000 /* 4M */
-#define CONFIG_SYS_MEMTEST_END 0x007fffff /*(_8M -1) */
#define CONFIG_SYS_LOAD_ADDR 0x00800000 /* default load adr- 8M */
-/* pseudo-non volatile RAM [hex] */
-#define CONFIG_KM_PNVRAM 0x80000
-/* physical RAM MTD size [hex] */
-#define CONFIG_KM_PHRAM 0x17F000
-
-#define CONFIG_KM_CRAMFS_ADDR 0x2400000
-#define CONFIG_KM_KERNEL_ADDR 0x2000000 /* 3098KBytes */
-#define CONFIG_KM_FDT_ADDR 0x23E0000 /* 128KBytes */
-
/* architecture specific default bootargs */
#define CONFIG_KM_DEF_BOOT_ARGS_CPU \
"bootcountaddr=${bootcountaddr} ${mtdparts}" \
""
#define CONFIG_SKIP_LOWLEVEL_INIT /* disable board lowlevel_init */
-#define CONFIG_MISC_INIT_R
-
-/*
- * NS16550 Configuration
- */
-#define CONFIG_SYS_NS16550_SERIAL
-#define CONFIG_SYS_NS16550_REG_SIZE (-4)
-#define CONFIG_SYS_NS16550_CLK CONFIG_SYS_TCLK
-#define CONFIG_SYS_NS16550_COM1 KW_UART0_BASE
-#define CONFIG_SYS_NS16550_COM2 KW_UART1_BASE
-
-/*
- * Serial Port configuration
- * The following definitions let you select what serial you want to use
- * for your console driver.
- */
/*
* For booting Linux, the board info and command line data
* have to be in the first 8 MB of memory, since this is
* the maximum mapped by the Linux kernel during initialization.
*/
-#define CONFIG_BOOTMAPSZ (8 << 20) /* Initial Memmap for Linux */
#define CONFIG_CMDLINE_TAG /* enable passing of ATAGs */
#define CONFIG_INITRD_TAG /* enable INITRD tag */
#define CONFIG_SETUP_MEMORY_TAGS /* enable memory tag */
*/
#define CONFIG_SYS_MAX_NAND_DEVICE 1
-#define BOOTFLASH_START 0x0
-
-/* Kirkwood has two serial IF */
-#if (CONFIG_CONS_INDEX == 2)
-#define CONFIG_KM_CONSOLE_TTY "ttyS1"
-#else
-#define CONFIG_KM_CONSOLE_TTY "ttyS0"
-#endif
-
/*
* Other required minimal configurations
*/
-#define CONFIG_ARCH_CPU_INIT /* call arch_cpu_init() */
-#define CONFIG_SYS_RESET_ADDRESS 0xffff0000 /* Rst Vector Adr */
/*
* Ethernet Driver configuration
*/
-#define CONFIG_NETCONSOLE /* include NetConsole support */
-#define CONFIG_SYS_FAULT_ECHO_LINK_DOWN /* detect link using phy */
+#define PHY_ANEG_TIMEOUT 8000 /* PHY needs a longer autoneg timeout */
#define CONFIG_MVGBE_PORTS {1, 0} /* enable port 0 only */
#define CONFIG_PHY_BASE_ADR 0
-#define CONFIG_ENV_OVERWRITE /* ethaddr can be reprogrammed */
-#define CONFIG_KM_COMMON_ETH_INIT /* standard km ethernet_present for piggy */
/*
* I2C related stuff
#ifndef __ASSEMBLY__
#include <asm/arch/gpio.h>
+#include <linux/delay.h>
+#include <linux/stringify.h>
extern void __set_direction(unsigned pin, int high);
void set_sda(int state);
void set_scl(int state);
* Environment variables configurations
*/
#if defined CONFIG_KM_ENV_IS_IN_SPI_NOR
-#define CONFIG_ENV_OFFSET 0xc0000 /* no bracets! */
-#define CONFIG_ENV_SIZE 0x02000 /* Size of Environment */
-#define CONFIG_ENV_SECT_SIZE 0x10000
-#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + \
- CONFIG_ENV_SECT_SIZE)
#define CONFIG_ENV_TOTAL_SIZE 0x20000 /* no bracets! */
#else
#define CONFIG_SYS_DEF_EEPROM_ADDR 0x50
#define CONFIG_ENV_EEPROM_IS_ON_I2C
#define CONFIG_SYS_EEPROM_WREN
-#define CONFIG_ENV_OFFSET 0x0 /* no bracets! */
-#define CONFIG_ENV_SIZE (0x2000 - CONFIG_ENV_OFFSET)
#define CONFIG_I2C_ENV_EEPROM_BUS 5 /* I2C2 (Mux-Port 5) */
-#define CONFIG_ENV_OFFSET_REDUND 0x2000 /* no bracets! */
-#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE)
#endif
-#define CONFIG_SYS_REDUNDAND_ENVIRONMENT
-
-
-/* SPI bus claim MPP configuration */
-#define CONFIG_SYS_KW_SPI_MPP 0x0
-
-#define FLASH_GPIO_PIN 0x00010000
#define KM_FLASH_GPIO_PIN 16
#define CONFIG_KM_UPDATE_UBOOT \
"arch=arm\0" \
""
-#if !defined(CONFIG_MTD_NOR_FLASH)
-#undef CONFIG_FLASH_CFI_MTD
-#undef CONFIG_JFFS2_CMDLINE
-#endif
-
/* additions for new relocation code, must be added to all boards */
#define CONFIG_SYS_SDRAM_BASE 0x00000000
-/* Do early setups now in board_init_f() */
-/*
- * resereved pram area at the end of memroy [hex]
- * 8Mbytes for switch + 4Kbytes for bootcount
- */
-#define CONFIG_KM_RESERVED_PRAM 0x801000
/* address for the bootcount (taken from end of RAM) */
#define BOOTCOUNT_ADDR (CONFIG_KM_RESERVED_PRAM)
#define CONFIG_POST_SKIP_ENV_FLAGS
#define CONFIG_POST_EXTERNAL_WORD_FUNCS
-/* we do the whole PCIe FPGA config stuff here */
-
#endif /* _CONFIG_KM_ARM_H */