#ifndef _CONFIG_KM_ARM_H
#define _CONFIG_KM_ARM_H
-#define CONFIG_SYS_GENERIC_BOARD
-
-/* We got removed from Linux mach-types.h */
-#define MACH_TYPE_KM_KIRKWOOD 2255
-
/*
* High Level Configuration Options (easy to change)
*/
/* include common defines/options for all Keymile boards */
#include "keymile-common.h"
-#define CONFIG_CMD_NAND
-#define CONFIG_CMD_SF
-
/* SPI NOR Flash default params, used by sf commands */
#define CONFIG_SF_DEFAULT_SPEED 8100000
#define CONFIG_SF_DEFAULT_MODE SPI_MODE_3
"u-boot="__stringify(CONFIG_HOSTNAME) "/u-boot.kwb\0" \
CONFIG_KM_UPDATE_UBOOT \
"set_fdthigh=setenv fdt_high ${kernelmem}\0" \
+ "checkfdt=" \
+ "if cramfsls fdt_0x${IVM_BoardId}_0x${IVM_HWKey}.dtb; " \
+ "then true; else setenv cramfsloadfdt true; " \
+ "setenv boot bootm ${load_addr_r}; " \
+ "echo No FDT found, booting with the kernel " \
+ "appended one; fi\0" \
""
#define CONFIG_SKIP_LOWLEVEL_INIT /* disable board lowlevel_init */
#define CONFIG_MISC_INIT_R
-/* Pass open firmware flat tree */
-#define CONFIG_OF_LIBFDT
-
/*
* NS16550 Configuration
*/
-#define CONFIG_SYS_NS16550
#define CONFIG_SYS_NS16550_SERIAL
#define CONFIG_SYS_NS16550_REG_SIZE (-4)
#define CONFIG_SYS_NS16550_CLK CONFIG_SYS_TCLK
#define CONFIG_SETUP_MEMORY_TAGS /* enable memory tag */
/*
- * Commands configuration
- */
-#define CONFIG_CMD_ELF
-#define CONFIG_CMD_MTDPARTS
-
-/*
- * Without NOR FLASH we need this
- */
-#define CONFIG_SYS_NO_FLASH
-
-/*
* NAND Flash configuration
*/
#define CONFIG_SYS_MAX_NAND_DEVICE 1
/*
* Other required minimal configurations
*/
-#define CONFIG_CONSOLE_INFO_QUIET /* some code reduction */
#define CONFIG_ARCH_CPU_INIT /* call arch_cpu_init() */
-#define CONFIG_ARCH_MISC_INIT /* call arch_misc_init() */
-#define CONFIG_DISPLAY_CPUINFO /* Display cpu info */
#define CONFIG_NR_DRAM_BANKS 4
#define CONFIG_SYS_RESET_ADDRESS 0xffff0000 /* Rst Vector Adr */
*/
#define CONFIG_NETCONSOLE /* include NetConsole support */
#define CONFIG_MII /* expose smi ove miiphy interface */
-#define CONFIG_CMD_MII /* to debug mdio phy config */
#define CONFIG_MVGBE /* Enable Marvell Gbe Controller Driver */
#define CONFIG_SYS_FAULT_ECHO_LINK_DOWN /* detect link using phy */
#define CONFIG_MVGBE_PORTS {1, 0} /* enable port 0 only */
#define CONFIG_KM_COMMON_ETH_INIT /* standard km ethernet_present for piggy */
/*
- * UBI related stuff
- */
-#define CONFIG_SYS_USE_UBI
-
-/*
* I2C related stuff
*/
#undef CONFIG_I2C_MVTWSI
#define CONFIG_SYS_I2C_SOFT_SPEED 100000
/* EEprom support 24C128, 24C256 valid for environment eeprom */
-#define CONFIG_SYS_I2C_MULTI_EEPROMS
#define CONFIG_SYS_EEPROM_PAGE_WRITE_ENABLE
#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 6 /* 64 Byte write page */
#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10
* Environment variables configurations
*/
#if defined CONFIG_KM_ENV_IS_IN_SPI_NOR
-#define CONFIG_ENV_IS_IN_SPI_FLASH /* use SPI-Flash for environment vars */
#define CONFIG_ENV_OFFSET 0xc0000 /* no bracets! */
#define CONFIG_ENV_SIZE 0x02000 /* Size of Environment */
#define CONFIG_ENV_SECT_SIZE 0x10000
CONFIG_ENV_SECT_SIZE)
#define CONFIG_ENV_TOTAL_SIZE 0x20000 /* no bracets! */
#else
-#define CONFIG_ENV_IS_IN_EEPROM /* use EEPROM for environment vars */
#define CONFIG_SYS_DEF_EEPROM_ADDR 0x50
#define CONFIG_ENV_EEPROM_IS_ON_I2C
#define CONFIG_SYS_EEPROM_WREN
#define CONFIG_ENV_OFFSET 0x0 /* no bracets! */
#define CONFIG_ENV_SIZE (0x2000 - CONFIG_ENV_OFFSET)
-#define CONFIG_I2C_ENV_EEPROM_BUS KM_ENV_BUS
+#define CONFIG_I2C_ENV_EEPROM_BUS 5 /* I2C2 (Mux-Port 5) */
#define CONFIG_ENV_OFFSET_REDUND 0x2000 /* no bracets! */
#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE)
#endif
#define CONFIG_SYS_REDUNDAND_ENVIRONMENT
-#define CONFIG_SPI_FLASH_STMICRO
/* SPI bus claim MPP configuration */
#define CONFIG_SYS_KW_SPI_MPP 0x0
"arch=arm\0" \
""
-#if defined(CONFIG_SYS_NO_FLASH)
+#if !defined(CONFIG_MTD_NOR_FLASH)
#undef CONFIG_FLASH_CFI_MTD
#undef CONFIG_JFFS2_CMDLINE
#endif
/* additions for new relocation code, must be added to all boards */
#define CONFIG_SYS_SDRAM_BASE 0x00000000
/* Do early setups now in board_init_f() */
-#define CONFIG_BOARD_EARLY_INIT_F
/*
* resereved pram area at the end of memroy [hex]
#define CONFIG_POST (CONFIG_SYS_POST_MEM_REGIONS)
#define CONFIG_POST_SKIP_ENV_FLAGS
#define CONFIG_POST_EXTERNAL_WORD_FUNCS
-#define CONFIG_CMD_DIAG
/* we do the whole PCIe FPGA config stuff here */
-#define CONFIG_BOARD_LATE_INIT
#endif /* _CONFIG_KM_ARM_H */