arm: Disable ATAGs support

[platform/kernel/u-boot.git] / include / configs / km / km_arm.h

diff --git a/include/configs/km/km_arm.h b/include/configs/km/km_arm.h
index 29060fa..29fcce9 100644 (file)
--- a/include/configs/km/km_arm.h
+++ b/include/configs/km/km_arm.h
@@ -32,16 +32,11 @@
 /* include common defines/options for all Keymile boards */
 #include "keymile-common.h"
 
-/* Reserve 4 MB for malloc */
-#define CONFIG_SYS_MALLOC_LEN          (4 * 1024 * 1024)
-
 /* Increase max size of compressed kernel */
 #define CONFIG_SYS_BOOTM_LEN           (32 << 20)
 
 #include "asm/arch/config.h"
 
-#define CONFIG_SYS_LOAD_ADDR   0x00800000      /* default load adr- 8M */
-
 /* architecture specific default bootargs */
 #define CONFIG_KM_DEF_BOOT_ARGS_CPU                                    \
                "bootcountaddr=${bootcountaddr} ${mtdparts}"            \
@@ -59,17 +54,6 @@
                "appended one; fi\0"                                    \
        ""
 
-#define CONFIG_SKIP_LOWLEVEL_INIT      /* disable board lowlevel_init */
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_CMDLINE_TAG             /* enable passing of ATAGs  */
-#define CONFIG_INITRD_TAG              /* enable INITRD tag */
-#define CONFIG_SETUP_MEMORY_TAGS       /* enable memory tag */
-
 /*
  * NAND Flash configuration
  */
@@ -90,8 +74,6 @@
  * I2C related stuff
  */
 #undef CONFIG_I2C_MVTWSI
-#define CONFIG_SYS_I2C
-#define        CONFIG_SYS_I2C_SOFT     /* I2C bit-banged       */
 #define CONFIG_SYS_I2C_INIT_BOARD
 
 #define        CONFIG_KIRKWOOD_GPIO            /* Enable GPIO Support */
@@ -110,10 +92,6 @@
 #include <linux/delay.h>
 #include <linux/stringify.h>
 extern void __set_direction(unsigned pin, int high);
-void set_sda(int state);
-void set_scl(int state);
-int get_sda(void);
-int get_scl(void);
 #define KM_KIRKWOOD_SDA_PIN    8
 #define KM_KIRKWOOD_SCL_PIN    9
 #define KM_KIRKWOOD_SOFT_I2C_GPIOS     0x0300
@@ -129,16 +107,8 @@ int get_scl(void);
 #define I2C_DELAY      udelay(1)
 #define I2C_SOFT_DECLARATIONS
 
-#define        CONFIG_SYS_I2C_SOFT_SLAVE       0x0
-#define        CONFIG_SYS_I2C_SOFT_SPEED       100000
-
 /* EEprom support 24C128, 24C256 valid for environment eeprom */
 #define CONFIG_SYS_EEPROM_PAGE_WRITE_ENABLE
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS      6 /* 64 Byte write page */
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS  10
-
-#define CONFIG_SYS_I2C_EEPROM_ADDR     0x50
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2
 
 /*
  *  Environment variables configurations
@@ -146,8 +116,6 @@ int get_scl(void);
 #if defined CONFIG_KM_ENV_IS_IN_SPI_NOR
 #define CONFIG_ENV_TOTAL_SIZE          0x20000     /* no bracets! */
 #else
-#define CONFIG_SYS_DEF_EEPROM_ADDR     0x50
-#define CONFIG_ENV_EEPROM_IS_ON_I2C
 #define CONFIG_SYS_EEPROM_WREN
 #define CONFIG_I2C_ENV_EEPROM_BUS 5 /* I2C2 (Mux-Port 5) */
 #endif
@@ -169,9 +137,9 @@ int get_scl(void);
        "newenv=setenv addr 0x100000 && "                               \
                "i2c dev " __stringify(CONFIG_I2C_ENV_EEPROM_BUS) "; "  \
                "mw.b ${addr} 0 4 && "                                  \
-               "eeprom write " __stringify(CONFIG_SYS_DEF_EEPROM_ADDR) \
+               "eeprom write " __stringify(CONFIG_SYS_I2C_EEPROM_ADDR) \
                " ${addr} " __stringify(CONFIG_ENV_OFFSET) " 4 && "     \
-               "eeprom write " __stringify(CONFIG_SYS_DEF_EEPROM_ADDR) \
+               "eeprom write " __stringify(CONFIG_SYS_I2C_EEPROM_ADDR) \
                " ${addr} " __stringify(CONFIG_ENV_OFFSET_REDUND) " 4\0"
 #endif