#define CONFIG_405EX 1 /* Specifc 405EX support*/
#define CONFIG_SYS_CLK_FREQ 33333333 /* ext frequency to pll */
+#ifndef CONFIG_SYS_TEXT_BASE
+#define CONFIG_SYS_TEXT_BASE 0xFFFA0000
+#endif
+
+/*
+ * CHIP_21 errata - you must set this to match your exact CPU, else your
+ * board will not boot. DO NOT enable this unless you have JTAG available
+ * for recovery, in the event you get it wrong.
+ *
+ * Kilauea uses the 405EX, while Haleakala uses the 405EXr. Either board
+ * may be equipped for security or not. You must look at the CPU part
+ * number to be sure what you have.
+ */
+/* #define CONFIG_SYS_4xx_CHIP_21_405EX_NO_SECURITY */
+/* #define CONFIG_SYS_4xx_CHIP_21_405EX_SECURITY */
+/* #define CONFIG_SYS_4xx_CHIP_21_405EXr_NO_SECURITY */
+/* #define CONFIG_SYS_4xx_CHIP_21_405EXr_SECURITY */
+
/*
* Include common defines/options for all AMCC eval boards
*/
#define CONFIG_SYS_INIT_RAM_ADDR (CONFIG_SYS_SDRAM_BASE + (32 << 20)) /* 32 MiB */
#endif /* defined(CONFIG_SYS_INIT_DCACHE_CS) */
-#define CONFIG_SYS_INIT_RAM_END (4 << 10) /* 4 KiB */
-#define CONFIG_SYS_GBL_DATA_SIZE 256 /* num bytes initial data */
-#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_RAM_SIZE (4 << 10) /* 4 KiB */
+#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
/*
* If the data cache is being used for the primordial stack and global
#define CONFIG_SYS_NAND_ECCSIZE 256
#define CONFIG_SYS_NAND_ECCBYTES 3
-#define CONFIG_SYS_NAND_ECCSTEPS (CONFIG_SYS_NAND_PAGE_SIZE / CONFIG_SYS_NAND_ECCSIZE)
#define CONFIG_SYS_NAND_OOBSIZE 16
-#define CONFIG_SYS_NAND_ECCTOTAL (CONFIG_SYS_NAND_ECCBYTES * CONFIG_SYS_NAND_ECCSTEPS)
#define CONFIG_SYS_NAND_ECCPOS {0, 1, 2, 3, 6, 7}
#ifdef CONFIG_ENV_IS_IN_NAND
*/
#define CONFIG_CMD_CHIP_CONFIG
#define CONFIG_CMD_DATE
-#define CONFIG_CMD_LOG
#define CONFIG_CMD_NAND
#define CONFIG_CMD_PCI
#define CONFIG_CMD_SNTP
CONFIG_SYS_POST_UART)
/* Define here the base-addresses of the UARTs to test in POST */
-#define CONFIG_SYS_POST_UART_TABLE {UART0_BASE, UART1_BASE}
+#define CONFIG_SYS_POST_UART_TABLE { CONFIG_SYS_NS16550_COM1, \
+ CONFIG_SYS_NS16550_COM2 }
#define CONFIG_LOGBUFFER
#define CONFIG_SYS_POST_CACHE_ADDR 0x00800000 /* free virtual address */