#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */
#define CONFIG_MISC_INIT_R 1 /* Call misc_init_r */
+#define CONFIG_BOARD_EMAC_COUNT
/*-----------------------------------------------------------------------
* Base addresses -- Note these are effective addresses where the
#define CFG_FPGA_BASE 0xF0000000
#define CFG_PERIPHERAL_BASE 0xEF600000 /* internal peripherals*/
#define CFG_MONITOR_LEN (384 * 1024) /* Reserve 384 kB for Monitor */
-#define CFG_MALLOC_LEN (128 * 1024) /* Reserve 128 kB for malloc() */
+#define CFG_MALLOC_LEN (512 * 1024) /* Reserve 512 kB for malloc() */
#define CFG_MONITOR_BASE (TEXT_BASE)
/*-----------------------------------------------------------------------
#define CFG_ENV_SIZE_REDUND (CFG_ENV_SIZE)
#endif /* CFG_ENV_IS_IN_FLASH */
+/*
+ * IPL (Initial Program Loader, integrated inside CPU)
+ * Will load first 4k from NAND (SPL) into cache and execute it from there.
+ *
+ * SPL (Secondary Program Loader)
+ * Will load special U-Boot version (NUB) from NAND and execute it. This SPL
+ * has to fit into 4kByte. It sets up the CPU and configures the SDRAM
+ * controller and the NAND controller so that the special U-Boot image can be
+ * loaded from NAND to SDRAM.
+ *
+ * NUB (NAND U-Boot)
+ * This NAND U-Boot (NUB) is a special U-Boot version which can be started
+ * from RAM. Therefore it mustn't (re-)configure the SDRAM controller.
+ *
+ * On 440EPx the SPL is copied to SDRAM before the NAND controller is
+ * set up. While still running from cache, I experienced problems accessing
+ * the NAND controller. sr - 2006-08-25
+ */
+#define CFG_NAND_BOOT_SPL_SRC 0xfffff000 /* SPL location */
+#define CFG_NAND_BOOT_SPL_SIZE (4 << 10) /* SPL size */
+#define CFG_NAND_BOOT_SPL_DST 0x00800000 /* Copy SPL here */
+#define CFG_NAND_U_BOOT_DST 0x01000000 /* Load NUB to this addr */
+#define CFG_NAND_U_BOOT_START CFG_NAND_U_BOOT_DST /* Start NUB from this addr */
+#define CFG_NAND_BOOT_SPL_DELTA (CFG_NAND_BOOT_SPL_SRC - CFG_NAND_BOOT_SPL_DST)
+
+/*
+ * Define the partitioning of the NAND chip (only RAM U-Boot is needed here)
+ */
+#define CFG_NAND_U_BOOT_OFFS (16 << 10) /* Offset to RAM U-Boot image */
+#define CFG_NAND_U_BOOT_SIZE (384 << 10) /* Size of RAM U-Boot image */
+
+/*
+ * Now the NAND chip has to be defined (no autodetection used!)
+ */
+#define CFG_NAND_PAGE_SIZE 512 /* NAND chip page size */
+#define CFG_NAND_BLOCK_SIZE (16 << 10) /* NAND chip block size */
+#define CFG_NAND_PAGE_COUNT 32 /* NAND chip page count */
+#define CFG_NAND_BAD_BLOCK_POS 5 /* Location of bad block marker */
+#define CFG_NAND_4_ADDR_CYCLE 1 /* Fourth addr used (>32MB) */
+
+#define CFG_NAND_ECCSIZE 256
+#define CFG_NAND_ECCBYTES 3
+#define CFG_NAND_ECCSTEPS (CFG_NAND_PAGE_SIZE / CFG_NAND_ECCSIZE)
+#define CFG_NAND_OOBSIZE 16
+#define CFG_NAND_ECCTOTAL (CFG_NAND_ECCBYTES * CFG_NAND_ECCSTEPS)
+#define CFG_NAND_ECCPOS {0, 1, 2, 3, 6, 7}
+
+#ifdef CFG_ENV_IS_IN_NAND
+/*
+ * For NAND booting the environment is embedded in the U-Boot image. Please take
+ * look at the file board/amcc/sequoia/u-boot-nand.lds for details.
+ */
+#define CFG_ENV_SIZE CFG_NAND_BLOCK_SIZE
+#define CFG_ENV_OFFSET (CFG_NAND_U_BOOT_OFFS + CFG_ENV_SIZE)
+#define CFG_ENV_OFFSET_REDUND (CFG_ENV_OFFSET + CFG_ENV_SIZE)
+#endif
+
+/*-----------------------------------------------------------------------
+ * NAND FLASH
+ *----------------------------------------------------------------------*/
+#define CFG_MAX_NAND_DEVICE 1
+#define NAND_MAX_CHIPS 1
+#define CFG_NAND_BASE (CFG_NAND_ADDR + CFG_NAND_CS)
+#define CFG_NAND_SELECT_DEVICE 1 /* nand driver supports mutipl. chips */
+
/*-----------------------------------------------------------------------
* DDR SDRAM
*----------------------------------------------------------------------*/
#define CFG_RX_ETH_BUFFER 32 /* Number of ethernet rx buffers & descriptors */
#define CONFIG_PREBOOT "echo;" \
- "echo Type \"run flash_nfs\" to mount root filesystem over NFS;" \
+ "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \
"echo"
#undef CONFIG_BOOTARGS
-#undef USE_LIBFDT
-#ifdef USE_LIBFDT
-/*
- * LIBFDT support is disabled for now since first Linux port is still
- * arch/ppc.
- */
#define CONFIG_EXTRA_ENV_SETTINGS \
"logversion=2\0" \
"netdev=eth0\0" \
"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
":${hostname}:${netdev}:off panic=1\0" \
"addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\
- "net_nfs=tftp 200000 ${bootfile};" \
- "tftp ${fdt_addr} ${fdt_file};" \
- "run nfsargs addip addtty;" \
- "bootm 200000 - ${fdt_addr}\0" \
- "flash_nfs=run nfsargs addip addtty;" \
- "bootm ${kernel_addr}\0" \
- "flash_self=run ramargs addip addtty;" \
+ "flash_self_old=run ramargs addip addtty;" \
"bootm ${kernel_addr} ${ramdisk_addr}\0" \
- "rootpath=/opt/eldk/ppc_4xx\0" \
- "bootfile=kilauea/uImage\0" \
- "fdt_file=kilauea/kilauea.dtb\0" \
- "fdt_addr=400000\0" \
- "kernel_addr=fc000000\0" \
- "ramdisk_addr=fc200000\0" \
- "initrd_high=30000000\0" \
- "load=tftp 200000 kilauea/u-boot.bin\0" \
- "update=protect off fffa0000 ffffffff;era fffa0000 ffffffff;" \
- "cp.b ${fileaddr} fffa0000 ${filesize};" \
- "setenv filesize;saveenv\0" \
- "upd=run load update\0" \
- "nload=tftp 200000 kilauea/u-boot-nand.bin\0" \
- "nupdate=nand erase 0 60000;nand write 200000 0 60000;" \
- "setenv filesize;saveenv\0" \
- "nupd=run nload nupdate\0" \
- ""
-#else
-#define CONFIG_EXTRA_ENV_SETTINGS \
- "logversion=2\0" \
- "netdev=eth0\0" \
- "hostname=kilauea\0" \
- "nfsargs=setenv bootargs root=/dev/nfs rw " \
- "nfsroot=${serverip}:${rootpath}\0" \
- "ramargs=setenv bootargs root=/dev/ram rw\0" \
- "addip=setenv bootargs ${bootargs} " \
- "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
- ":${hostname}:${netdev}:off panic=1\0" \
- "addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\
- "net_nfs=tftp 200000 ${bootfile};" \
- "run nfsargs addip addtty;" \
- "bootm 200000\0" \
- "flash_nfs=run nfsargs addip addtty;" \
- "bootm ${kernel_addr}\0" \
"flash_self=run ramargs addip addtty;" \
- "bootm ${kernel_addr} ${ramdisk_addr}\0" \
+ "bootm ${kernel_addr} ${ramdisk_addr} ${fdt_addr}\0" \
+ "flash_nfs_old=run nfsargs addip addtty;" \
+ "bootm ${kernel_addr}\0" \
+ "flash_nfs=run nfsargs addip addtty;" \
+ "bootm ${kernel_addr} - ${fdt_addr}\0" \
+ "net_nfs_old=tftp ${kernel_addr_r} ${bootfile};" \
+ "run nfsargs addip addtty;bootm ${kernel_addr_r}\0" \
+ "net_nfs=tftp ${kernel_addr_r} ${bootfile}; " \
+ "tftp ${fdt_addr_r} ${fdt_file}; " \
+ "run nfsargs addip addtty;" \
+ "bootm ${kernel_addr_r} - ${fdt_addr_r}\0" \
"rootpath=/opt/eldk/ppc_4xx\0" \
"bootfile=kilauea/uImage\0" \
+ "fdt_file=kilauea/kilauea.dtb\0" \
+ "kernel_addr_r=400000\0" \
+ "fdt_addr_r=800000\0" \
"kernel_addr=fc000000\0" \
+ "fdt_addr=fc1e0000\0" \
"ramdisk_addr=fc200000\0" \
"initrd_high=30000000\0" \
"load=tftp 200000 kilauea/u-boot.bin\0" \
"setenv filesize;saveenv\0" \
"nupd=run nload nupdate\0" \
"pciconfighost=1\0" \
+ "pcie_mode=RP:RP\0" \
""
-#endif
#define CONFIG_BOOTCOMMAND "run flash_self"
#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
#define CONFIG_BOOTP_BOOTPATH
#define CONFIG_BOOTP_GATEWAY
#define CONFIG_BOOTP_HOSTNAME
+#define CONFIG_BOOTP_SUBNETMASK
/*
* Command line configuration.
#define CONFIG_CMD_PCI
#define CONFIG_CMD_PING
#define CONFIG_CMD_REGINFO
+#define CONFIG_CMD_SNTP
/* POST support */
#define CONFIG_POST (CFG_POST_MEMORY | \
#define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */
#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */
#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */
+#define CFG_CONSOLE_INFO_QUIET 1 /* don't print console @ startup*/
/*-----------------------------------------------------------------------
* PCI stuff
#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
/*-----------------------------------------------------------------------
- * Cache Configuration
- *----------------------------------------------------------------------*/
-#define CFG_DCACHE_SIZE (16 << 10) /* For IBM 405EX */
-#define CFG_CACHELINE_SIZE 32
-#if defined(CONFIG_CMD_KGDB)
-#define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */
-#endif
-
-/*-----------------------------------------------------------------------
* External Bus Controller (EBC) Setup
*----------------------------------------------------------------------*/
+#if defined(CONFIG_NAND_U_BOOT) || defined(CONFIG_NAND_SPL)
+/* booting from NAND, so NAND chips select has to be on CS 0 */
+#define CFG_NAND_CS 0 /* NAND chip connected to CSx */
+
+/* Memory Bank 1 (NOR-FLASH) initialization */
+#define CFG_EBC_PB1AP 0x05806500
+#define CFG_EBC_PB1CR 0xFC0DA000 /* BAS=0xFC0,BS=64MB,BU=R/W,BW=16bit*/
+
+/* Memory Bank 0 (NAND-FLASH) initialization */
+#define CFG_EBC_PB0AP 0x018003c0
+#define CFG_EBC_PB0CR (CFG_NAND_ADDR | 0x1e000)
+#else
#define CFG_NAND_CS 1 /* NAND chip connected to CSx */
/* Memory Bank 0 (NOR-FLASH) initialization */
/* Memory Bank 1 (NAND-FLASH) initialization */
#define CFG_EBC_PB1AP 0x018003c0
#define CFG_EBC_PB1CR (CFG_NAND_ADDR | 0x1e000)
+#endif
/* Memory Bank 2 (FPGA) initialization */
#define CFG_EBC_PB2AP 0x9400C800
#define CFG_EBC_CFG 0x7FC00000 /* EBC0_CFG */
/*-----------------------------------------------------------------------
- * NAND FLASH
- *----------------------------------------------------------------------*/
-#define CFG_MAX_NAND_DEVICE 1
-#define NAND_MAX_CHIPS 1
-#define CFG_NAND_BASE (CFG_NAND_ADDR + CFG_NAND_CS)
-#define CFG_NAND_SELECT_DEVICE 1 /* nand driver supports mutipl. chips */
-
-/*-----------------------------------------------------------------------
* GPIO Setup
*----------------------------------------------------------------------*/
-/*-----------------------------------------------------------------------
- * Definitions for GPIO setup (PPC405EX specific)
- *
- * GPIO0[0-3] - EBC data 0-3 inputs/outputs
- * GPIO0[4-7] - USB data 4-7 inputs/outputs
- * GPIO0[8-11] - NFCE# 1-3 inputs/outputs, GPIO11: IRQ6 inputs
- * GPIO0[12-15] - USB data 0-3 inputs/outputs
- * GPIO0[16-21] - UART0 control signal inputs/outputs
- *
- * GPIO0[22-25,27] - EBC control signal inputs/outputs
- * GPIO0[26] - Instruction trace outputs
- * GPIO0[28] - Float, N/C
- * GPIO0[29-31] - DMA control signal inputs/outputs
- */
-#define CFG_GPIO0_OSRL 0x00AA54AA
-#define CFG_GPIO0_OSRH 0x21800000
-#define CFG_GPIO0_TSRL 0x00AA55AA
-#define CFG_GPIO0_TSRH 0xA5A00000
-
-#define CFG_GPIO0_ISR1L 0x00000100
-#define CFG_GPIO0_ISR1H 0x04000000
-#define CFG_GPIO0_ISR2L 0x00550055
-#define CFG_GPIO0_ISR2H 0x40100000
+#define CFG_4xx_GPIO_TABLE { /* Out GPIO Alternate1 Alternate2 Alternate3 */ \
+{ \
+/* GPIO Core 0 */ \
+{GPIO0_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_0}, /* GPIO0 EBC_DATA_PAR(0) */ \
+{GPIO0_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_0}, /* GPIO1 EBC_DATA_PAR(1) */ \
+{GPIO0_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_0}, /* GPIO2 EBC_DATA_PAR(2) */ \
+{GPIO0_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_0}, /* GPIO3 EBC_DATA_PAR(3) */ \
+{GPIO0_BASE, GPIO_BI, GPIO_ALT2, GPIO_OUT_0}, /* GPIO4 EBC_DATA(20) USB2_DATA(4) */ \
+{GPIO0_BASE, GPIO_BI, GPIO_ALT2, GPIO_OUT_0}, /* GPIO5 EBC_DATA(21) USB2_DATA(5) */ \
+{GPIO0_BASE, GPIO_BI, GPIO_ALT2, GPIO_OUT_0}, /* GPIO6 EBC_DATA(22) USB2_DATA(6) */ \
+{GPIO0_BASE, GPIO_BI, GPIO_ALT2, GPIO_OUT_0}, /* GPIO7 EBC_DATA(23) USB2_DATA(7) */ \
+{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO8 CS(1)/NFCE(1) IRQ(7) */ \
+{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO9 CS(2)/NFCE(2) IRQ(8) */ \
+{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO10 CS(3)/NFCE(3) IRQ(9) */ \
+{GPIO0_BASE, GPIO_IN, GPIO_ALT1, GPIO_OUT_0}, /* GPIO11 IRQ(6) */ \
+{GPIO0_BASE, GPIO_BI, GPIO_ALT2, GPIO_OUT_0}, /* GPIO12 EBC_DATA(16) USB2_DATA(0) */ \
+{GPIO0_BASE, GPIO_BI, GPIO_ALT2, GPIO_OUT_0}, /* GPIO13 EBC_DATA(17) USB2_DATA(1) */ \
+{GPIO0_BASE, GPIO_BI, GPIO_ALT2, GPIO_OUT_0}, /* GPIO14 EBC_DATA(18) USB2_DATA(2) */ \
+{GPIO0_BASE, GPIO_BI, GPIO_ALT2, GPIO_OUT_0}, /* GPIO15 EBC_DATA(19) USB2_DATA(3) */ \
+{GPIO0_BASE, GPIO_IN, GPIO_ALT1, GPIO_OUT_0}, /* GPIO16 UART0_DCD UART1_CTS */ \
+{GPIO0_BASE, GPIO_IN, GPIO_ALT1, GPIO_OUT_0}, /* GPIO17 UART0_DSR UART1_RTS */ \
+{GPIO0_BASE, GPIO_IN, GPIO_ALT1, GPIO_OUT_0}, /* GPIO18 UART0_CTS */ \
+{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO19 UART0_RTS */ \
+{GPIO0_BASE, GPIO_OUT, GPIO_ALT2, GPIO_OUT_0}, /* GPIO20 UART0_DTR UART1_TX */ \
+{GPIO0_BASE, GPIO_IN, GPIO_ALT2, GPIO_OUT_0}, /* GPIO21 UART0_RI UART1_RX */ \
+{GPIO0_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_0}, /* GPIO22 EBC_HOLD_REQ DMA_ACK2 */ \
+{GPIO0_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_0}, /* GPIO23 EBC_HOLD_ACK DMA_REQ2 */ \
+{GPIO0_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_0}, /* GPIO24 EBC_EXT_REQ DMA_EOT2 IRQ(4) */ \
+{GPIO0_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_0}, /* GPIO25 EBC_EXT_ACK DMA_ACK3 IRQ(3) */ \
+{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO26 EBC_ADDR(5) DMA_EOT0 TS(3) */ \
+{GPIO0_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_0}, /* GPIO27 EBC_BUS_REQ DMA_EOT3 IRQ(5) */ \
+{GPIO0_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_0}, /* GPIO28 */ \
+{GPIO0_BASE, GPIO_IN, GPIO_ALT2, GPIO_OUT_0}, /* GPIO29 DMA_EOT1 IRQ(2) */ \
+{GPIO0_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_0}, /* GPIO30 DMA_REQ1 IRQ(1) */ \
+{GPIO0_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_0}, /* GPIO31 DMA_ACK1 IRQ(0) */ \
+} \
+}
/*
* Internal Definitions
#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
#define BOOTFLAG_WARM 0x02 /* Software reboot */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
#endif
* Some Kilauea stuff..., mainly fpga registers
*/
#define CFG_FPGA_REG_BASE CFG_FPGA_BASE
-#define CFG_FPGA_FIFO_BASE (in32(CFG_FPGA_BASE) | (1 << 11))
+#define CFG_FPGA_FIFO_BASE (in32(CFG_FPGA_BASE) | (1 << 10))
/* interrupt */
#define CFG_FPGA_SLIC0_R_DPRAM_INT 0x80000000
#define CFG_FPGA_USER_LED0 0x00000200
#define CFG_FPGA_USER_LED1 0x00000100
-#endif /* __CONFIG_H */
-
-#ifdef USE_LIBFDT
/* pass open firmware flat tree */
#define CONFIG_OF_LIBFDT 1
#define CONFIG_OF_BOARD_SETUP 1
-#define OF_CPU "PowerPC,405EX@0"
-#endif
+#endif /* __CONFIG_H */
projects / platform / kernel / u-boot.git / blobdiff