* Base addresses -- Note these are effective addresses where the
* actual resources get mapped (not physical addresses)
*----------------------------------------------------------------------*/
-#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */
-#define CFG_MALLOC_LEN (512 * 1024) /* Reserve 512 kB for malloc */
-
#define CFG_SDRAM_BASE 0x00000000 /* _must_ be 0 */
#define CFG_FLASH_BASE 0xff000000 /* start of FLASH */
-#define CFG_MONITOR_BASE TEXT_BASE
#define CFG_PERIPHERAL_BASE 0xa0000000 /* internal peripherals */
#define CFG_ISRAM_BASE 0x90000000 /* internal SRAM */
#define CFG_ACE_BASE 0xfe000000 /* Xilinx ACE controller - Compact Flash */
+#define CFG_MONITOR_BASE TEXT_BASE
+#define CFG_MONITOR_LEN (0xFFFFFFFF - CFG_MONITOR_BASE + 1)
+#define CFG_MALLOC_LEN (512 * 1024) /* Reserve 512 kB for malloc */
+
/*-----------------------------------------------------------------------
* Initial RAM & stack pointer (placed in internal SRAM)
*----------------------------------------------------------------------*/
#define CONFIG_SPD_EEPROM 1 /* Use SPD EEPROM for setup */
#define SPD_EEPROM_ADDRESS {0x51, 0x52} /* SPD i2c spd addresses*/
#define CONFIG_DDR_ECC 1 /* with ECC support */
+#define CONFIG_DDR_RQDC_FIXED 0x80000038 /* optimal value found by GDA*/
#undef CONFIG_STRESS
/*-----------------------------------------------------------------------
#define CFG_ENV_IS_IN_FLASH 1 /* Environment uses flash */
#define CONFIG_PREBOOT "echo;" \
- "echo Type \"run flash_nfs\" to mount root filesystem over NFS;" \
+ "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \
"echo"
#undef CONFIG_BOOTARGS
+#define xstr(s) str(s)
+#define str(s) #s
+
#define CONFIG_EXTRA_ENV_SETTINGS \
"netdev=eth0\0" \
"hostname=katmai\0" \
"bootm ${kernel_addr} ${ramdisk_addr}\0" \
"net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;" \
"bootm\0" \
- "rootpath=/opt/eldk/ppc_4xx\0" \
+ "net_nfs_fdt=tftp 200000 ${bootfile};" \
+ "tftp ${fdt_addr} ${fdt_file};" \
+ "run nfsargs addip addtty;" \
+ "bootm 200000 - ${fdt_addr}\0" \
+ "rootpath=/opt/eldk/ppc_4xx\0" \
"bootfile=katmai/uImage\0" \
+ "fdt_file=katmai/katmai.dtb\0" \
+ "fdt_addr=400000\0" \
"kernel_addr=fff10000\0" \
"ramdisk_addr=fff20000\0" \
"initrd_high=30000000\0" \
"load=tftp 200000 katmai/u-boot.bin\0" \
- "update=protect off fffc0000 ffffffff;era fffc0000 ffffffff;" \
- "cp.b ${fileaddr} fffc0000 ${filesize};" \
+ "update=protect off " xstr(CFG_MONITOR_BASE) " FFFFFFFF;" \
+ "era " xstr(CFG_MONITOR_BASE) " FFFFFFFF;" \
+ "cp.b ${fileaddr} " xstr(CFG_MONITOR_BASE) " ${filesize};" \
"setenv filesize;saveenv\0" \
- "upd=run load;run update\0" \
+ "upd=run load update\0" \
"kozio=bootm ffc60000\0" \
"pciconfighost=1\0" \
"pcie_mode=RP:RP:RP\0" \
#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
#endif
+/* pass open firmware flat tree */
+#define CONFIG_OF_LIBFDT 1
+#define CONFIG_OF_BOARD_SETUP 1
+
#endif /* __CONFIG_H */