Drop digital thermometer and thermostat (DTT) drivers

[platform/kernel/u-boot.git] / include / configs / katmai.h

diff --git a/include/configs/katmai.h b/include/configs/katmai.h
index e3fede5..c3b9da0 100644 (file)
--- a/include/configs/katmai.h
+++ b/include/configs/katmai.h
@@ -37,7 +37,6 @@
 #define CONFIG_HOSTNAME                katmai
 #include "amcc-common.h"
 
-#define CONFIG_BOARD_EARLY_INIT_F 1    /* Call board_pre_init          */
 #undef  CONFIG_SHOW_BOOT_PROGRESS
 
 /*-----------------------------------------------------------------------
@@ -124,31 +123,6 @@
 #define CONFIG_SYS_I2C_RTC_ADDR        0x68
 #define CONFIG_SYS_M41T11_BASE_YEAR    1900    /* play along with linux        */
 
-/* I2C DTT */
-#define CONFIG_DTT_ADM1021     1       /* ADM1021 temp sensor support  */
-#define CONFIG_SYS_DTT_BUS_NUM         1       /* The I2C bus for DTT          */
-/*
- * standard dtt sensor configuration - bottom bit will determine local or
- * remote sensor of the ADM1021, the rest determines index into
- * CONFIG_SYS_DTT_ADM1021 array below.
- */
-#define CONFIG_DTT_SENSORS     { 0, 1 }
-
-/*
- * ADM1021 temp sensor configuration (see dtt/adm1021.c for details).
- * there will be one entry in this array for each two (dummy) sensors in
- * CONFIG_DTT_SENSORS.
- *
- * For Katmai board:
- * - only one ADM1021
- * - i2c addr 0x18
- * - conversion rate 0x02 = 0.25 conversions/second
- * - ALERT ouput disabled
- * - local temp sensor enabled, min set to 0 deg, max set to 85 deg
- * - remote temp sensor enabled, min set to 0 deg, max set to 85 deg
- */
-#define CONFIG_SYS_DTT_ADM1021         { { 0x18, 0x02, 0, 1, 0, 85, 1, 0, 58} }
-
 /*-----------------------------------------------------------------------
  * Environment
  *----------------------------------------------------------------------*/
@@ -171,8 +145,6 @@
 /*
  * Commands additional to the ones defined in amcc-common.h
  */
-#define CONFIG_CMD_CHIP_CONFIG
-#define CONFIG_CMD_DATE
 #define CONFIG_CMD_ECCTEST
 #define CONFIG_CMD_PCI
 #define CONFIG_CMD_SDRAM
@@ -214,9 +186,7 @@
  *-----------------------------------------------------------------------
  */
 /* General PCI */
-#define CONFIG_PCI                     /* include pci support          */
 #define CONFIG_PCI_INDIRECT_BRIDGE     /* indirect PCI bridge support */
-#define CONFIG_PCI_PNP         1       /* do pci plug-and-play         */
 #define CONFIG_PCI_SCAN_SHOW   1       /* show pci devices on startup  */
 #define CONFIG_PCI_CONFIG_HOST_BRIDGE
 
@@ -240,7 +210,6 @@
 #define CONFIG_SYSTEMACE       1       /* Enable SystemACE support     */
 #define CONFIG_SYS_SYSTEMACE_WIDTH     16      /* Data bus width is 16         */
 #define CONFIG_SYS_SYSTEMACE_BASE      CONFIG_SYS_ACE_BASE
-#define CONFIG_DOS_PARTITION   1
 
 /*-----------------------------------------------------------------------
  * External Bus Controller (EBC) Setup