#define __CONFIG_J721E_EVM_H
#include <linux/sizes.h>
-#include <config_distro_bootcmd.h>
-#include <environment/ti/mmc.h>
-#include <environment/ti/k3_rproc.h>
-#include <environment/ti/ufs.h>
-#include <environment/ti/k3_dfu.h>
/* DDR Configuration */
-#define CONFIG_SYS_SDRAM_BASE1 0x880000000
+#define CFG_SYS_SDRAM_BASE1 0x880000000
+/* FLASH Configuration */
+#define CFG_SYS_FLASH_BASE 0x000000000
/* SPL Loader Configuration */
#if defined(CONFIG_TARGET_J721E_A72_EVM) || defined(CONFIG_TARGET_J7200_A72_EVM)
-#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SPL_TEXT_BASE + \
- CONFIG_SYS_K3_NON_SECURE_MSRAM_SIZE)
-#define CONFIG_SYS_UBOOT_BASE 0x50280000
+#define CFG_SYS_UBOOT_BASE 0x50280000
/* Image load address in RAM for DFU boot*/
#else
-#define CONFIG_SYS_UBOOT_BASE 0x50080000
-/*
- * Maximum size in memory allocated to the SPL BSS. Keep it as tight as
- * possible (to allow the build to go through), as this directly affects
- * our memory footprint. The less we use for BSS the more we have available
- * for everything else.
- */
-#define CONFIG_SPL_BSS_MAX_SIZE 0xA000
-/*
- * Link BSS to be within SPL in a dedicated region located near the top of
- * the MCU SRAM, this way making it available also before relocation. Note
- * that we are not using the actual top of the MCU SRAM as there is a memory
- * location filled in by the boot ROM that we want to read out without any
- * interference from the C context.
- */
-#define CONFIG_SPL_BSS_START_ADDR (CONFIG_SYS_K3_BOOT_PARAM_TABLE_INDEX -\
- CONFIG_SPL_BSS_MAX_SIZE)
-/* Set the stack right below the SPL BSS section */
-#define CONFIG_SYS_INIT_SP_ADDR CONFIG_SPL_BSS_START_ADDR
-/* Configure R5 SPL post-relocation malloc pool in DDR */
-#define CONFIG_SYS_SPL_MALLOC_START 0x84000000
-#define CONFIG_SYS_SPL_MALLOC_SIZE SZ_16M
-/* Image load address in RAM for DFU boot*/
+#define CFG_SYS_UBOOT_BASE 0x50080000
#endif
-#ifdef CONFIG_SYS_K3_SPL_ATF
-#define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME "tispl.bin"
+#if CONFIG_IS_ENABLED(CMD_PXE)
+# define BOOT_TARGET_PXE(func) func(PXE, pxe, na)
+#else
+# define BOOT_TARGET_PXE(func)
#endif
-#define CONFIG_SPL_MAX_SIZE CONFIG_SYS_K3_MAX_DOWNLODABLE_IMAGE_SIZE
-
-#define CONFIG_SYS_BOOTM_LEN SZ_64M
-#define CONFIG_CQSPI_REF_CLK 133333333
-
-/* HyperFlash related configuration */
-#define CONFIG_SYS_MAX_FLASH_BANKS_DETECT 1
-
-/* U-Boot general configuration */
-#define EXTRA_ENV_J721E_BOARD_SETTINGS \
- "default_device_tree=" CONFIG_DEFAULT_DEVICE_TREE ".dtb\0" \
- "findfdt=" \
- "setenv name_fdt ${default_device_tree};" \
- "setenv fdtfile ${name_fdt}\0" \
- "loadaddr=0x80080000\0" \
- "fdtaddr=0x82000000\0" \
- "overlayaddr=0x83000000\0" \
- "name_kern=Image\0" \
- "console=ttyS2,115200n8\0" \
- "args_all=setenv optargs earlycon=ns16550a,mmio32,0x02800000 " \
- "${mtdparts}\0" \
- "run_kern=booti ${loadaddr} ${rd_spec} ${fdtaddr}\0"
-
-#define PARTS_DEFAULT \
- /* Linux partitions */ \
- "uuid_disk=${uuid_gpt_disk};" \
- "name=rootfs,start=0,size=-,uuid=${uuid_gpt_rootfs}\0"
-
-#ifdef CONFIG_SYS_K3_SPL_ATF
-#define EXTRA_ENV_R5_SPL_RPROC_FW_ARGS_MMC \
- "addr_mainr5f0_0load=0x88000000\0" \
- "name_mainr5f0_0fw=/lib/firmware/j7-main-r5f0_0-fw\0" \
- "addr_mcur5f0_0load=0x89000000\0" \
- "name_mcur5f0_0fw=/lib/firmware/j7-mcu-r5f0_0-fw\0"
+#if CONFIG_IS_ENABLED(CMD_DHCP)
+# define BOOT_TARGET_DHCP(func) func(DHCP, dhcp, na)
#else
-#define EXTRA_ENV_R5_SPL_RPROC_FW_ARGS_MMC ""
-#endif /* CONFIG_SYS_K3_SPL_ATF */
-
-/* U-Boot MMC-specific configuration */
-#define EXTRA_ENV_J721E_BOARD_SETTINGS_MMC \
- "boot=mmc\0" \
- "mmcdev=1\0" \
- "bootpart=1:2\0" \
- "bootdir=/boot\0" \
- EXTRA_ENV_R5_SPL_RPROC_FW_ARGS_MMC \
- "rd_spec=-\0" \
- "init_mmc=run args_all args_mmc\0" \
- "get_fdt_mmc=load mmc ${bootpart} ${fdtaddr} ${bootdir}/${name_fdt}\0" \
- "get_overlay_mmc=" \
- "fdt address ${fdtaddr};" \
- "fdt resize 0x100000;" \
- "for overlay in $name_overlays;" \
- "do;" \
- "load mmc ${bootpart} ${overlayaddr} ${bootdir}/${overlay} && " \
- "fdt apply ${overlayaddr};" \
- "done;\0" \
- "partitions=" PARTS_DEFAULT \
- "get_kern_mmc=load mmc ${bootpart} ${loadaddr} " \
- "${bootdir}/${name_kern}\0" \
- "get_fit_mmc=load mmc ${bootpart} ${addr_fit} " \
- "${bootdir}/${name_fit}\0" \
- "partitions=" PARTS_DEFAULT
-
-/* Set the default list of remote processors to boot */
-#if defined(CONFIG_TARGET_J721E_A72_EVM) || defined(CONFIG_TARGET_J7200_A72_EVM)
-#ifdef DEFAULT_RPROCS
-#undef DEFAULT_RPROCS
+# define BOOT_TARGET_DHCP(func)
#endif
-#endif
-
-#ifdef CONFIG_TARGET_J721E_A72_EVM
-#define DEFAULT_RPROCS "" \
- "3 /lib/firmware/j7-main-r5f0_1-fw " \
- "4 /lib/firmware/j7-main-r5f1_0-fw " \
- "5 /lib/firmware/j7-main-r5f1_1-fw " \
- "6 /lib/firmware/j7-c66_0-fw " \
- "7 /lib/firmware/j7-c66_1-fw " \
- "8 /lib/firmware/j7-c71_0-fw "
-#endif /* CONFIG_TARGET_J721E_A72_EVM */
-
-#ifdef CONFIG_TARGET_J7200_A72_EVM
-#define DEFAULT_RPROCS "" \
- "2 /lib/firmware/j7200-main-r5f0_0-fw " \
- "3 /lib/firmware/j7200-main-r5f0_1-fw "
-#endif /* CONFIG_TARGET_J7200_A72_EVM */
-/* set default dfu_bufsiz to 128KB (sector size of OSPI) */
-#define EXTRA_ENV_DFUARGS \
- "dfu_bufsiz=0x20000\0" \
- DFU_ALT_INFO_MMC \
- DFU_ALT_INFO_EMMC \
- DFU_ALT_INFO_RAM \
- DFU_ALT_INFO_OSPI
-
-#if defined(CONFIG_TARGET_J721E_A72_EVM) || defined(CONFIG_TARGET_J7200_A72_EVM)
-#define EXTRA_ENV_J721E_BOARD_SETTINGS_MTD \
- "mtdids=" CONFIG_MTDIDS_DEFAULT "\0" \
- "mtdparts=" CONFIG_MTDPARTS_DEFAULT "\0"
+#ifdef CONFIG_CMD_USB
+# define BOOT_TARGET_USB(func) func(USB, usb, 0)
#else
-#define EXTRA_ENV_J721E_BOARD_SETTINGS_MTD
+# define BOOT_TARGET_USB(func)
#endif
+#define BOOT_TARGET_DEVICES(func) \
+ BOOT_TARGET_USB(func) \
+ func(MMC, mmc, 1) \
+ func(MMC, mmc, 0) \
+ BOOT_TARGET_PXE(func) \
+ BOOT_TARGET_DHCP(func)
+
+#include <config_distro_bootcmd.h>
+
/* Incorporate settings into the U-Boot environment */
-#define CONFIG_EXTRA_ENV_SETTINGS \
- DEFAULT_MMC_TI_ARGS \
- DEFAULT_FIT_TI_ARGS \
- EXTRA_ENV_J721E_BOARD_SETTINGS \
- EXTRA_ENV_J721E_BOARD_SETTINGS_MMC \
- EXTRA_ENV_RPROC_SETTINGS \
- EXTRA_ENV_DFUARGS \
- DEFAULT_UFS_TI_ARGS \
- EXTRA_ENV_J721E_BOARD_SETTINGS_MTD
+#define CFG_EXTRA_ENV_SETTINGS \
+ BOOTENV
/* Now for the remaining common defines */
#include <configs/ti_armv7_common.h>
projects / platform / kernel / u-boot.git / blobdiff