Convert CONFIG_CMD_IRQ to Kconfig

[platform/kernel/u-boot.git] / include / configs / ipek01.h

diff --git a/include/configs/ipek01.h b/include/configs/ipek01.h
index 3f6f8dd..c6390db 100644 (file)
--- a/include/configs/ipek01.h
+++ b/include/configs/ipek01.h
@@ -19,8 +19,6 @@
 #define CONFIG_MPX5200         1       /* MPX5200 board */
 #define CONFIG_MPC5200_DDR     1       /* use DDR RAM */
 #define CONFIG_IPEK01                  /* Motherboard is ipek01 */
-#define CONFIG_SYS_GENERIC_BOARD
-#define CONFIG_DISPLAY_BOARDINFO
 
 #define        CONFIG_SYS_TEXT_BASE    0xfc000000
 
@@ -37,7 +35,6 @@
  * Serial console configuration
  */
 #define CONFIG_PSC_CONSOLE     1       /* console is on PSC1 */
-#define CONFIG_BAUDRATE                115200  /* ... at 9600 bps */
 #define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 }
 
 #define CONFIG_CMDLINE_EDITING 1       /* add command line history */
@@ -45,18 +42,12 @@
 /*
  * Video configuration for LIME GDC
  */
-#define CONFIG_VIDEO
 #ifdef CONFIG_VIDEO
 #define CONFIG_VIDEO_MB862xx
 #define CONFIG_VIDEO_MB862xx_ACCEL
 #define VIDEO_FB_16BPP_WORD_SWAP
-#define CONFIG_CFB_CONSOLE
 #define CONFIG_VIDEO_LOGO
 #define CONFIG_VIDEO_BMP_LOGO
-#define CONFIG_CONSOLE_EXTRA_INFO
-#define CONFIG_VGA_AS_SINGLE_DEVICE
-#define CONFIG_SYS_CONSOLE_IS_IN_ENV
-#define CONFIG_VIDEO_SW_CURSOR
 #define CONFIG_SPLASH_SCREEN
 #define CONFIG_VIDEO_BMP_GZIP
 #define CONFIG_SYS_VIDEO_LOGO_MAX_SIZE (2 << 20)       /* decompressed img */
@@ -71,8 +62,6 @@
  * 0x40000000 - 0x4fffffff - PCI Memory
  * 0x50000000 - 0x50ffffff - PCI IO Space
  */
-#define CONFIG_PCI             1
-#define CONFIG_PCI_PNP         1
 #define CONFIG_PCI_SCAN_SHOW   1
 
 #define CONFIG_PCI_MEM_BUS     0x40000000
@@ -87,13 +76,9 @@
 #define CONFIG_EEPRO100                1
 #define CONFIG_SYS_RX_ETH_BUFFER       8  /* use 8 rx buffer on eepro100  */
 
-/* Partitions */
-#define CONFIG_DOS_PARTITION
-
 /* USB */
 #define CONFIG_USB_OHCI_NEW
 #define CONFIG_SYS_OHCI_BE_CONTROLLER
-#define CONFIG_USB_STORAGE
 
 #define CONFIG_SYS_USB_OHCI_CPU_INIT
 #define CONFIG_SYS_USB_OHCI_REGS_BASE          MPC5XXX_USB
@@ -103,25 +88,13 @@
 /*
  * Command line configuration.
  */
-#ifdef CONFIG_VIDEO
-#define CONFIG_CMD_BMP         /* BMP support */
-#endif
-#define CONFIG_CMD_DATE                /* support for RTC, date/time...*/
-#define CONFIG_CMD_DHCP                /* DHCP Support */
-#define CONFIG_CMD_FAT         /* FAT support */
-#define CONFIG_CMD_I2C         /* I2C serial bus support */
-#define CONFIG_CMD_IDE         /* IDE harddisk support */
-#define CONFIG_CMD_IRQ         /* irqinfo */
-#define CONFIG_CMD_MII         /* MII support */
 #define CONFIG_CMD_PCI         /* pciinfo */
-#define CONFIG_CMD_USB         /* USB Support */
 
 #define CONFIG_SYS_LOWBOOT     1
 
 /*
  * Autobooting
  */
-#define CONFIG_BOOTDELAY       5       /* autoboot after 5 seconds */
 
 #define CONFIG_PREBOOT "echo;" \
        "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \
@@ -171,36 +144,10 @@
 /*
  * Open firmware flat tree support
  */
-#define CONFIG_OF_LIBFDT       1
-#define CONFIG_OF_BOARD_SETUP  1
-
 #define OF_CPU                 "PowerPC,5200@0"
 #define OF_SOC                 "soc5200@f0000000"
 #define OF_TBCLK               (bd->bi_busfreq / 4)
 
-/*
- * I2C configuration
- */
-#define CONFIG_HARD_I2C                1       /* I2C with hardware support */
-#define CONFIG_SYS_I2C_MODULE  2       /* Select I2C module #1 or #2 */
-
-#define CONFIG_SYS_I2C_SPEED   100000  /* 100 kHz */
-#define CONFIG_SYS_I2C_SLAVE   0x7F
-
-/*
- * EEPROM configuration
- */
-#define CONFIG_SYS_I2C_EEPROM_ADDR             0x53
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN         2
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS      6
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS  10
-
-/*
- * RTC configuration
- */
-#define CONFIG_RTC_PCF8563
-#define CONFIG_SYS_I2C_RTC_ADDR                0x51
-
 #define CONFIG_SYS_FLASH_BASE          0xFC000000
 #define CONFIG_SYS_FLASH_SIZE          0x01000000
 #define CONFIG_ENV_ADDR                        (CONFIG_SYS_FLASH_BASE + \
@@ -295,8 +242,6 @@
 
 #define CONFIG_SYS_LOAD_ADDR           0x100000 /* default load address */
 
-#define CONFIG_LOOPW
-
 /*
  * Various low-level settings
  */