#define CONFIG_SYS_OSCIN_FREQ 24000000
#define CONFIG_SYS_TIMERBASE DAVINCI_TIMER0_BASE
#define CONFIG_SYS_HZ_CLOCK clk_get(DAVINCI_AUXCLK_CLKID)
-#define CONFIG_SYS_DA850_PLL_INIT
-#define CONFIG_SYS_DA850_DDR_INIT
#define CONFIG_SYS_TEXT_BASE 0xc1080000
/*
#define CONFIG_SYS_NS16550_COM1 DAVINCI_UART0_BASE /* Base address of UART0 */
#define CONFIG_SYS_NS16550_CLK clk_get(DAVINCI_UART2_CLKID)
#define CONFIG_CONS_INDEX 1 /* use UART0 for console */
-#define CONFIG_BAUDRATE 115200 /* Default baud rate */
/*
* Flash & Environment
*/
#define CONFIG_NAND_DAVINCI
-#define CONFIG_SYS_NO_FLASH
-#define CONFIG_ENV_IS_IN_NAND /* U-Boot env in NAND Flash */
#define CONFIG_ENV_OFFSET 0x0 /* Block 0--not used by bootcode */
#define CONFIG_ENV_SIZE (128 << 10)
#define CONFIG_SYS_NAND_USE_FLASH_BBT
#define CONFIG_SYS_NAND_ECCSIZE 512
#define CONFIG_SYS_NAND_ECCBYTES 10
#define CONFIG_SYS_NAND_OOBSIZE 64
-#define CONFIG_SPL_NAND_SUPPORT
#define CONFIG_SPL_NAND_BASE
#define CONFIG_SPL_NAND_DRIVERS
#define CONFIG_SPL_NAND_ECC
* U-Boot general configuration
*/
#define CONFIG_MISC_INIT_R
-#define CONFIG_BOARD_EARLY_INIT_F
#define CONFIG_BOOTFILE "uImage" /* Boot file name */
#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)
#define CONFIG_AUTO_COMPLETE
#define CONFIG_CMDLINE_EDITING
#define CONFIG_SYS_LONGHELP
-#define CONFIG_CRC32_VERIFY
#define CONFIG_MX_CYCLIC
/*
"nand write c0000100 180000 20000\0" \
"\0"
-/*
- * U-Boot commands
- */
-#define CONFIG_CMD_ENV
-#define CONFIG_CMD_DIAG
-#define CONFIG_CMD_SAVES
-
#ifdef CONFIG_CMD_BDI
#define CONFIG_CLOCKS
#endif
#ifndef CONFIG_DRIVER_TI_EMAC
#endif
-#define CONFIG_CMD_NAND
-#define CONFIG_CMD_NAND_TRIMFFS
-
-#define CONFIG_CMD_MTDPARTS
#define CONFIG_MTD_DEVICE
#define CONFIG_MTD_PARTITIONS
-#define CONFIG_LZO
-#define CONFIG_RBTREE
-#define CONFIG_CMD_UBI
-#define CONFIG_CMD_UBIFS
#define MTDIDS_NAME_STR "davinci_nand.0"
#define MTDIDS_DEFAULT "nand0=" MTDIDS_NAME_STR
/* defines for SPL */
#define CONFIG_SPL_FRAMEWORK
-#define CONFIG_SPL_BOARD_INIT
#define CONFIG_SYS_SPL_MALLOC_START (CONFIG_SYS_TEXT_BASE - \
CONFIG_SYS_MALLOC_LEN)
#define CONFIG_SYS_SPL_MALLOC_SIZE CONFIG_SYS_MALLOC_LEN
-#define CONFIG_SPL_SERIAL_SUPPORT
-#define CONFIG_SPL_LIBGENERIC_SUPPORT
-#define CONFIG_SPL_LDSCRIPT "board/$(BOARDDIR)/u-boot-spl-ipam390.lds"
#define CONFIG_SPL_STACK 0x8001ff00
#define CONFIG_SPL_TEXT_BASE 0x80000000
#define CONFIG_SPL_MAX_SIZE 0x20000
GENERATED_GBL_DATA_SIZE)
/* add FALCON boot mode */
-#define CONFIG_CMD_SPL
-#define CONFIG_SPL_OS_BOOT
#define CONFIG_SYS_NAND_SPL_KERNEL_OFFS 0x00200000
#define CONFIG_SYS_SPL_ARGS_ADDR LINUX_BOOT_PARAM_ADDR
-#define CONFIG_CMD_SPL_NAND_OFS 0x00180000
-#define CONFIG_CMD_SPL_WRITE_SIZE 0x400
/* GPIO support */
#define CONFIG_DA8XX_GPIO
#define CONFIG_IPAM390_GPIO_LED_RED ((16 * 7) + 11)
#define CONFIG_IPAM390_GPIO_LED_GREEN ((16 * 7) + 12)
+#include <asm/arch/hardware.h>
+
#endif /* __CONFIG_H */