#define CONFIG_SYS_OSCIN_FREQ 24000000
#define CONFIG_SYS_TIMERBASE DAVINCI_TIMER0_BASE
#define CONFIG_SYS_HZ_CLOCK clk_get(DAVINCI_AUXCLK_CLKID)
-#define CONFIG_SYS_DA850_PLL_INIT
-#define CONFIG_SYS_DA850_DDR_INIT
#define CONFIG_SYS_TEXT_BASE 0xc1080000
/*
#define CONFIG_SYS_NS16550_COM1 DAVINCI_UART0_BASE /* Base address of UART0 */
#define CONFIG_SYS_NS16550_CLK clk_get(DAVINCI_UART2_CLKID)
#define CONFIG_CONS_INDEX 1 /* use UART0 for console */
-#define CONFIG_BAUDRATE 115200 /* Default baud rate */
/*
* Flash & Environment
*/
#define CONFIG_NAND_DAVINCI
-#define CONFIG_SYS_NO_FLASH
#define CONFIG_ENV_IS_IN_NAND /* U-Boot env in NAND Flash */
#define CONFIG_ENV_OFFSET 0x0 /* Block 0--not used by bootcode */
#define CONFIG_ENV_SIZE (128 << 10)
#define CONFIG_SYS_NAND_ECCSIZE 512
#define CONFIG_SYS_NAND_ECCBYTES 10
#define CONFIG_SYS_NAND_OOBSIZE 64
-#define CONFIG_SPL_NAND_SUPPORT
#define CONFIG_SPL_NAND_BASE
#define CONFIG_SPL_NAND_DRIVERS
#define CONFIG_SPL_NAND_ECC
* U-Boot general configuration
*/
#define CONFIG_MISC_INIT_R
-#define CONFIG_BOARD_EARLY_INIT_F
#define CONFIG_BOOTFILE "uImage" /* Boot file name */
#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)
#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Args Buffer Size */
#define CONFIG_SYS_LOAD_ADDR (PHYS_SDRAM_1 + 0x700000)
-#define CONFIG_VERSION_VARIABLE
#define CONFIG_AUTO_COMPLETE
#define CONFIG_CMDLINE_EDITING
#define CONFIG_SYS_LONGHELP
* U-Boot commands
*/
#define CONFIG_CMD_ENV
-#define CONFIG_CMD_DIAG
#define CONFIG_CMD_SAVES
#ifdef CONFIG_CMD_BDI
#define CONFIG_MTD_PARTITIONS
#define CONFIG_LZO
#define CONFIG_RBTREE
-#define CONFIG_CMD_UBI
#define CONFIG_CMD_UBIFS
#define MTDIDS_NAME_STR "davinci_nand.0"
/* defines for SPL */
#define CONFIG_SPL_FRAMEWORK
-#define CONFIG_SPL_BOARD_INIT
#define CONFIG_SYS_SPL_MALLOC_START (CONFIG_SYS_TEXT_BASE - \
CONFIG_SYS_MALLOC_LEN)
#define CONFIG_SYS_SPL_MALLOC_SIZE CONFIG_SYS_MALLOC_LEN
-#define CONFIG_SPL_SERIAL_SUPPORT
-#define CONFIG_SPL_LIBCOMMON_SUPPORT
-#define CONFIG_SPL_LIBGENERIC_SUPPORT
#define CONFIG_SPL_LDSCRIPT "board/$(BOARDDIR)/u-boot-spl-ipam390.lds"
#define CONFIG_SPL_STACK 0x8001ff00
#define CONFIG_SPL_TEXT_BASE 0x80000000
/* add FALCON boot mode */
#define CONFIG_CMD_SPL
-#define CONFIG_SPL_OS_BOOT
#define CONFIG_SYS_NAND_SPL_KERNEL_OFFS 0x00200000
#define CONFIG_SYS_SPL_ARGS_ADDR LINUX_BOOT_PARAM_ADDR
#define CONFIG_CMD_SPL_NAND_OFS 0x00180000
#define CONFIG_CMD_SPL_WRITE_SIZE 0x400
/* GPIO support */
-#define CONFIG_SPL_GPIO_SUPPORT
#define CONFIG_DA8XX_GPIO
#define CONFIG_IPAM390_GPIO_BOOTMODE ((16 * 7) + 14)