+/* SPDX-License-Identifier: GPL-2.0+ */
/*
* (C) Copyright 2012
* Linaro
* Linus Walleij <linus.walleij@linaro.org>
* Common ARM Integrator configuration settings
- *
- * SPDX-License-Identifier: GPL-2.0+
*/
-#define CONFIG_SYS_TEXT_BASE 0x01000000
-#define CONFIG_SYS_MEMTEST_START 0x100000
-#define CONFIG_SYS_MEMTEST_END 0x10000000
#define CONFIG_SYS_TIMERBASE 0x13000100 /* Timer1 */
-#define CONFIG_SYS_LOAD_ADDR 0x7fc0 /* default load address */
-#define CONFIG_SYS_LONGHELP
-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size*/
-#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 128*1024) /* Size of malloc() pool */
-
-/* Serial port PL010/PL011 through the device model */
-#define CONFIG_PL01X_SERIAL
-#define CONFIG_CONS_INDEX 0
-
-#define CONFIG_CMDLINE_TAG /* enable passing of ATAGs */
-#define CONFIG_SETUP_MEMORY_TAGS
-#define CONFIG_MISC_INIT_R /* call misc_init_r during start up */
-
-/*
- * There are various dependencies on the core module (CM) fitted
- * Users should refer to their CM user guide
- */
-#include "armcoremodule.h"
-
-/*
- * Initialize and remap the core module, use SPD to detect memory size
- * If CONFIG_SKIP_LOWLEVEL_INIT is not defined &
- * the core module has a CM_INIT register
- * then the U-Boot initialisation code will
- * e.g. ARM Boot Monitor or pre-loader is repeated once
- * (to re-initialise any existing CM_INIT settings to safe values).
- *
- * This is usually not the desired behaviour since the platform
- * will either reboot into the ARM monitor (or pre-loader)
- * or continuously cycle thru it without U-Boot running,
- * depending upon the setting of Integrator/CP switch S2-4.
- *
- * However it may be needed if Integrator/CP switch S2-1
- * is set OFF to boot direct into U-Boot.
- * In that case comment out the line below.
- */
-#define CONFIG_CM_INIT
-#define CONFIG_CM_REMAP
-#define CONFIG_CM_SPD_DETECT
/*
* The ARM boot monitor initializes the board.
* image to run at reset/power up
* e.g. whether the ARM Boot Monitor runs before U-Boot
*/
-/* #define CONFIG_SKIP_LOWLEVEL_INIT */
/*
* The ARM boot monitor does not relocate U-Boot.
/*
* Physical Memory Map
*/
-#define CONFIG_NR_DRAM_BANKS 1 /* we have 1 bank of DRAM */
#define PHYS_SDRAM_1 0x00000000 /* SDRAM Bank #1 */
#define PHYS_SDRAM_1_SIZE 0x08000000 /* 128 MB */
#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1
-#define CONFIG_SYS_INIT_RAM_SIZE PHYS_SDRAM_1_SIZE
-#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_SDRAM_BASE + \
- CONFIG_SYS_INIT_RAM_SIZE - \
- GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_ADDR CONFIG_SYS_GBL_DATA_OFFSET
/*
* FLASH and environment organization
* - SIB block
* - U-Boot environment
*/
-#define CONFIG_SYS_FLASH_CFI 1
-#define CONFIG_FLASH_CFI_DRIVER 1
#define CONFIG_SYS_FLASH_BASE 0x24000000
-#define CONFIG_SYS_MAX_FLASH_BANKS 1
/* Timeout values in ticks */
-#define CONFIG_SYS_FLASH_ERASE_TOUT (2 * CONFIG_SYS_HZ) /* Erase Timeout */
-#define CONFIG_SYS_FLASH_WRITE_TOUT (2 * CONFIG_SYS_HZ) /* Write Timeout */
-#define CONFIG_SYS_FLASH_PROTECTION /* The devices have real protection */
-#define CONFIG_SYS_FLASH_EMPTY_INFO /* flinfo indicates empty blocks */