#ifndef __CONFIG_H
#define __CONFIG_H
-#define DEBUG 1
-
-/*
- * If we are developing, we might want to start U-Boot from ram
- * so we MUST NOT initialize critical regs like mem-timing ...
- */
-#define CONFIG_INIT_CRITICAL /* undef for developing */
-
/*
* High Level Configuration Options
* (easy to change)
*/
-#define CONFIG_PXA250 1 /* This is an PXA250 CPU */
+#define CONFIG_PXA250 1 /* This is an PXA250 CPU */
#define CONFIG_INNOKOM 1 /* on an Auerswald Innokom board */
#undef CONFIG_USE_IRQ /* we don't need IRQ/FIQ stuff */
#define CONFIG_BAUDRATE 19200
#define CONFIG_MISC_INIT_R 1 /* we have a misc_init_r() function */
-#define CONFIG_COMMANDS (CONFIG_CMD_DFL|CFG_CMD_I2C|CFG_CMD_EEPROM|CFG_CMD_NET|CFG_CMD_JFFS2|CFG_CMD_DHCP)
-/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
-#include <cmd_confdefs.h>
+
+/*
+ * BOOTP options
+ */
+#define CONFIG_BOOTP_BOOTFILESIZE
+#define CONFIG_BOOTP_BOOTPATH
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_HOSTNAME
+
+
+/*
+ * Command line configuration.
+ */
+
+#define CONFIG_CMD_ASKENV
+#define CONFIG_CMD_BDI
+#define CONFIG_CMD_CACHE
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_ECHO
+#define CONFIG_CMD_ENV
+#define CONFIG_CMD_FLASH
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_IMI
+#define CONFIG_CMD_LOADB
+#define CONFIG_CMD_MEMORY
+#define CONFIG_CMD_NET
+#define CONFIG_CMD_RUN
+
#define CONFIG_BOOTDELAY 3
/* #define CONFIG_BOOTARGS "root=/dev/nfs ip=bootp console=ttyS0,19200" */
#define CONFIG_CMDLINE_TAG 1
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
-#define CONFIG_KGDB_BAUDRATE 19200 /* speed to run kgdb serial port */
-#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
-#endif
-
/*
* Miscellaneous configurable options
*/
/*
- * Size of malloc() pool; this lives below the uppermost 128 KiB which are
- * used for the RAM copy of the uboot code
- *
+ * Size of malloc() pool
*/
#define CFG_MALLOC_LEN (256*1024)
+#define CFG_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */
#define CFG_LONGHELP /* undef to save memory */
#define CFG_PROMPT "uboot> " /* Monitor Command Prompt */
#define CFG_MONITOR_LEN 0x20000 /* 128 KiB */
- /* valid baudrates */
+ /* valid baudrates */
#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
/*
* I2C bus
*/
-#define CONFIG_HARD_I2C 1
-#define CFG_I2C_SPEED 50000
-#define CFG_I2C_SLAVE 0xfe
+#define CONFIG_HARD_I2C 1
+#define CFG_I2C_SPEED 50000
+#define CFG_I2C_SLAVE 0xfe
-#define CFG_ENV_IS_IN_EEPROM 1
+#define CONFIG_ENV_IS_IN_EEPROM 1
-#define CFG_ENV_OFFSET 0x00 /* environment starts here */
-#define CFG_ENV_SIZE 1024 /* 1 KiB */
+#define CONFIG_ENV_OFFSET 0x00 /* environment starts here */
+#define CONFIG_ENV_SIZE 1024 /* 1 KiB */
#define CFG_I2C_EEPROM_ADDR 0x50 /* A0 = 0 (hardwired) */
#define CFG_EEPROM_PAGE_WRITE_BITS 5 /* 5 bits = 32 octets */
#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 15 /* between stop and start */
#define CONFIG_SMC91111_BASE 0x14000000 /* chip select 5 */
#undef CONFIG_SMC_USE_32_BIT /* 16 bit bus access */
#undef CONFIG_SMC_91111_EXT_PHY /* we use internal phy */
+#define CONFIG_SMC_AUTONEG_TIMEOUT 10 /* timeout 10 seconds */
#undef CONFIG_SHOW_ACTIVITY
#define CONFIG_NET_RETRY_COUNT 10 /* # of retries */
#define CFG_FLASH_BASE PHYS_FLASH_1
-
/*
- * JFFS2 Partitions
+ * JFFS2 partitions
+ *
*/
-#define CFG_JFFS_CUSTOM_PART 1 /* see board/innokom/flash.c */
-#define CONFIG_MTD_INNOKOM_16MB 1 /* development flash */
-#undef CONFIG_MTD_INNOKOM_64MB /* production flash */
+/* development flash */
+#define CONFIG_MTD_INNOKOM_16MB 1
+#undef CONFIG_MTD_INNOKOM_64MB
+
+/* production flash */
+/*
+#define CONFIG_MTD_INNOKOM_64MB 1
+#undef CONFIG_MTD_INNOKOM_16MB
+*/
+/* No command line, one static partition, whole device */
+#undef CONFIG_JFFS2_CMDLINE
+#define CONFIG_JFFS2_DEV "nor0"
+#define CONFIG_JFFS2_PART_SIZE 0xFFFFFFFF
+#define CONFIG_JFFS2_PART_OFFSET 0x00000000
+
+/* mtdparts command line support */
+/* Note: fake mtd_id used, no linux mtd map file */
+/*
+#define CONFIG_JFFS2_CMDLINE
+#define MTDIDS_DEFAULT "nor0=innokom-0"
+*/
+
+/* development flash */
+/*
+#define MTDPARTS_DEFAULT "mtdparts=innokom-0:256k(uboot),768k(kernel),8m(user),7m(data)"
+*/
+
+/* production flash */
+/*
+#define MTDPARTS_DEFAULT "mtdparts=innokom-0:256k(uboot),768k(kernel),16256k(user1),16256k(user2),32m(data)"
+*/
/*
- * GPIO settings; see BDI2000 config file for details
+ * GPIO settings
*
* GP15 == nCS1 is 1
* GP24 == SFRM is 1
* [32:26] 0 - reserved
* [25] 0 - K2FREE: not free running
* [24] 0 - K1FREE: not free running
- * [23] 0 - K0FREE: not free running
+ * [23] 1 - K0FREE: not free running
* [22] 0 - SLFRSH: self refresh disabled
* [21] 0 - reserved
* [20] 0 - APD: no auto power down
* [16] 1 - K1RUN: enable SDCLK1
* [15] 1 - E1PIN: SDRAM clock enable
* [14] 1 - K0DB2: SDCLK0 is MemClk
- * [13] 1 - K0RUN: disable SDCLK0
+ * [13] 0 - K0RUN: disable SDCLK0
* [12] 1 - E0PIN: disable SDCKE0
* [11:00] 000000011000 - (64ms/8192)*MemClkFreq/32 = 24
*/
-#define CFG_MDREFR_VAL 0x0001F018
+#define CFG_MDREFR_VAL 0x0081D018
/* MDMRS: Mode Register Set Configuration Register
*
projects / platform / kernel / u-boot.git / blobdiff