#undef CONFIG_USE_IRQ /* we don't need IRQ/FIQ stuff */
/* for timer/console/ethernet */
+
+#define CONFIG_SYS_TEXT_BASE 0x0
+
+/* we will never enable dcache, because we have to setup MMU first */
+#define CONFIG_SYS_DCACHE_OFF
+
/*
* Hardware drivers
*/
/*
* select serial console configuration
*/
+#define CONFIG_PXA_SERIAL
#define CONFIG_FFUART 1 /* we use FFUART on CSB226 */
/* allow to overwrite serial and ethaddr */
* Size of malloc() pool
*/
#define CONFIG_SYS_MALLOC_LEN (256*1024)
-#define CONFIG_SYS_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */
#define CONFIG_SYS_LONGHELP /* undef to save memory */
#define CONFIG_SYS_PROMPT "uboot> " /* Monitor Command Prompt */
#define CONFIG_SYS_MEMTEST_START 0xa0400000 /* memtest works on */
#define CONFIG_SYS_MEMTEST_END 0xa0800000 /* 4 ... 8 MB in DRAM */
-#undef CONFIG_SYS_CLKS_IN_HZ /* everything, incl board info, in Hz */
-
#define CONFIG_SYS_LOAD_ADDR 0xa3000000 /* load kernel to this address */
-#define CONFIG_SYS_HZ 3686400 /* incrementer freq: 3.6864 MHz */
+#define CONFIG_SYS_HZ 1000
/* RS: the oscillator is actually 3680130?? */
#define CONFIG_SYS_CPUSPEED 0x141 /* set core clock to 200/200/100 MHz */
/*
* I2C bus
*/
+#define CONFIG_I2C_MV 1
+#define CONFIG_MV_I2C_REG 0x40301680
#define CONFIG_HARD_I2C 1
#define CONFIG_SYS_I2C_SPEED 50000
#define CONFIG_SYS_I2C_SLAVE 0xfe
/*
* SMSC91C111 Network Card
*/
-#define CONFIG_DRIVER_SMC91111 1
+#define CONFIG_SMC91111 1
#define CONFIG_SMC91111_BASE 0x14000000 /* chip select 5 */
#undef CONFIG_SMC_USE_32_BIT /* 16 bit bus access */
#undef CONFIG_SMC_91111_EXT_PHY /* we use internal phy */
#define CONFIG_SYS_FLASH_BASE PHYS_FLASH_1
+#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1
+#define CONFIG_SYS_INIT_SP_ADDR (GENERATED_GBL_DATA_SIZE + PHYS_SDRAM_1)
+
/*
* JFFS2 partitions
*
*/
/* No command line, one static partition, whole device */
-#undef CONFIG_JFFS2_CMDLINE
+#undef CONFIG_CMD_MTDPARTS
#define CONFIG_JFFS2_DEV "nor0"
#define CONFIG_JFFS2_PART_SIZE 0xFFFFFFFF
#define CONFIG_JFFS2_PART_OFFSET 0x00000000
/* mtdparts command line support */
/* Note: fake mtd_id used, no linux mtd map file */
/*
-#define CONFIG_JFFS2_CMDLINE
+#define CONFIG_CMD_MTDPARTS
#define MTDIDS_DEFAULT "nor0=innokom-0"
*/
*/
#define CONFIG_SYS_PSSR_VAL 0x37
+#define CONFIG_SYS_CCCR CCCR_L27|CCCR_M2|CCCR_N10
+#define CONFIG_SYS_CKEN 0x0
+
/*
* Memory settings
*
#define CONFIG_SYS_MCIO0_VAL 0x00000000
#define CONFIG_SYS_MCIO1_VAL 0x00000000
+#define CONFIG_SYS_FLYCNFG_VAL 0x00000000
+#define CONFIG_SYS_SXCNFG_VAL 0x00000000
+
/*
#define CSB226_USER_LED0 0x00000008
#define CSB226_USER_LED1 0x00000010