#define __CONFIG_H
/*
- * If we are developing, we might want to start U-Boot from ram
- * so we MUST NOT initialize critical regs like mem-timing ...
- */
-#define CONFIG_INIT_CRITICAL /* undef for developing */
-
-/*
* High Level Configuration Options
* (easy to change)
*/
#define CONFIG_BAUDRATE 19200
#define CONFIG_MISC_INIT_R 1 /* we have a misc_init_r() function */
-#define CONFIG_COMMANDS (CFG_CMD_BDI|CFG_CMD_LOADB|CFG_CMD_IMI|CFG_CMD_FLASH|CFG_CMD_MEMORY|CFG_CMD_NET|CFG_CMD_ENV|CFG_CMD_RUN|CFG_CMD_ASKENV|CFG_CMD_ECHO|CFG_CMD_I2C|CFG_CMD_DHCP|CFG_CMD_CACHE)
-/* CONFIG_CMD_DFL|CFG_CMD_I2C|CFG_CMD_EEPROM|CFG_CMD_NET|CFG_CMD_JFFS2|CFG_CMD_DHCP) */
-/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
-#include <cmd_confdefs.h>
+
+/*
+ * BOOTP options
+ */
+#define CONFIG_BOOTP_BOOTFILESIZE
+#define CONFIG_BOOTP_BOOTPATH
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_HOSTNAME
+
+
+/*
+ * Command line configuration.
+ */
+
+#define CONFIG_CMD_ASKENV
+#define CONFIG_CMD_BDI
+#define CONFIG_CMD_CACHE
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_ECHO
+#define CONFIG_CMD_ENV
+#define CONFIG_CMD_FLASH
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_IMI
+#define CONFIG_CMD_LOADB
+#define CONFIG_CMD_MEMORY
+#define CONFIG_CMD_NET
+#define CONFIG_CMD_RUN
+
#define CONFIG_BOOTDELAY 3
/* #define CONFIG_BOOTARGS "root=/dev/nfs ip=bootp console=ttyS0,19200" */
*/
/*
- * Size of malloc() pool; this lives below the uppermost 128 KiB which are
- * used for the RAM copy of the uboot code
- *
+ * Size of malloc() pool
*/
#define CFG_MALLOC_LEN (256*1024)
+#define CFG_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */
#define CFG_LONGHELP /* undef to save memory */
#define CFG_PROMPT "uboot> " /* Monitor Command Prompt */
#define CONFIG_SMC91111_BASE 0x14000000 /* chip select 5 */
#undef CONFIG_SMC_USE_32_BIT /* 16 bit bus access */
#undef CONFIG_SMC_91111_EXT_PHY /* we use internal phy */
+#define CONFIG_SMC_AUTONEG_TIMEOUT 10 /* timeout 10 seconds */
#undef CONFIG_SHOW_ACTIVITY
#define CONFIG_NET_RETRY_COUNT 10 /* # of retries */
#define CFG_FLASH_BASE PHYS_FLASH_1
-
/*
- * JFFS2 Partitions
+ * JFFS2 partitions
+ *
*/
-#define CFG_JFFS_CUSTOM_PART 1 /* see board/innokom/flash.c */
-#define CONFIG_MTD_INNOKOM_16MB 1 /* development flash */
-#undef CONFIG_MTD_INNOKOM_64MB /* production flash */
+/* development flash */
+#define CONFIG_MTD_INNOKOM_16MB 1
+#undef CONFIG_MTD_INNOKOM_64MB
+
+/* production flash */
+/*
+#define CONFIG_MTD_INNOKOM_64MB 1
+#undef CONFIG_MTD_INNOKOM_16MB
+*/
+/* No command line, one static partition, whole device */
+#undef CONFIG_JFFS2_CMDLINE
+#define CONFIG_JFFS2_DEV "nor0"
+#define CONFIG_JFFS2_PART_SIZE 0xFFFFFFFF
+#define CONFIG_JFFS2_PART_OFFSET 0x00000000
+
+/* mtdparts command line support */
+/* Note: fake mtd_id used, no linux mtd map file */
+/*
+#define CONFIG_JFFS2_CMDLINE
+#define MTDIDS_DEFAULT "nor0=innokom-0"
+*/
+
+/* development flash */
+/*
+#define MTDPARTS_DEFAULT "mtdparts=innokom-0:256k(uboot),768k(kernel),8m(user),7m(data)"
+*/
+
+/* production flash */
+/*
+#define MTDPARTS_DEFAULT "mtdparts=innokom-0:256k(uboot),768k(kernel),16256k(user1),16256k(user2),32m(data)"
+*/
/*
* GPIO settings